Uniden DECT1363 Series User manual

DECT1363 base
with cordless
handset Battery
cover
Not pictured:
Rechargeable battery
(BT-1007)
AC adapter (PS-0035)
Telephone cord
-
-
-
If any items are missing or damaged, contact our Customer Care Line
immediately. Never use damaged products!
Need help? Get answers 24/7 at our website: www.uniden.com.
If You... Contact Uniden’s... Phone Number
have a question or problem Customer Care Line* 817-858-2929 or
800-297-1023
need a replacement part or an
accessory Parts Department* 800-554-3988
need special assistance due to
a disability Accessibility Help Line 800-874-9314 (voice or TTY)
* During regular business hours, Central Standard Time; see our website for
detailed business hours.


DECT1363 Series User's Guide
What's in the box?
© 2009 Uniden America Corp. Printed in Vietnam
Ft. Worth, Texas UNZZ01108BZ(0)

2

When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric shock and
injury to persons, including the following:
This unit is NOT waterproof. DO NOT expose it to rain/moisture.
Do not use this product near water, for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
Do not use a telephone to report a gas leak in the vicinity of the leak.
Use only the power cord and batteries indicated in this manual. Do
not dispose of batteries in a fire. They may explode. Check with local
codes for possible special disposal instructions.
Do not place the handset in any charging cradle without the battery
installed and the battery cover securely in place.


Dispose of used batteries according to the instructions. Do not open

product.
For more details, see the Important Information section.






What’s in the manual?
............................ 3
Installing Your Phone.................. 3
Geng to Know Your Phone ...... 4
Using the Menu .......................... 6
Using Your Phone ........................ 8
Basics .......................................... 8
Using the Phonebook ............... 10
Finding the Handset.................. 11
............... 11
Chain Dialing............................. 11
Using a Voice Mail Service........ 11
 .............. 12
Solving Problems ...................... 12
AC Adapter and Baery
Informaon ............................ 15
Compliance Informaon........... 16
Warranty (1 Year, Limited) ....... 19

3
GETTING STARTED

Charge the Baery
Unpack the handset, battery pack,
and battery cover. If you need to
remove the battery cover, press in
on the notch and slide the cover
down and off.
Line up the battery connector with the jack inside the handset.
(The battery connector will only fit one way.)
Push the connector in until it clicks into place; tug gently on the
wires to make sure the battery pack is securely connected.
Replace the battery cover and slide it into place.
Connect the AC adapter to the
AC IN 8V
jack on the base. Set the
plug into the notch.
Plug the other end of the adapter into a standard 120V AC outlet.
Place the handset in the base with the display facing forward. The
display on the handset should light up; if it doesn’t, reseat the
handset or try plugging the AC adapter into a different outlet.

Connect the Telephone Cord
Use the telephone cord to connect the
TEL LINE
jack on the base to a
standard telephone wall jack.
Test the Connecon
Pick up the handset from the cradle and press Talk . You should
hear a dial tone, and the display should say Talk.
If you don't hear a dial tone or the display says Check Tel Line,
check the connection between the base and the phone jack.
Make a quick test call. (Press End to hang up.)
If you keep hearing a dial tone, try changing to pulse dialing mode.
1.
2.
3.
4.
5.
6.
7.

1.

2.


4
If there is a lot of noise, see page 13 for tips on avoiding
interference.
Changing from Tone to Pulse Dialing
Your phone communicates with the telephone network in two ways:
tone dialing or pulse dialing. Most telephone companies use tone
dialing. If your phone company uses pulse dialing, you will need to
change your phone’s dial mode.
From the handset, open the menu and select Global Setup. (See
page 6 for details on using the menu.)
Select Dial Mode, then select Pulse. The phone sounds a
confirmation tone.
If you use pulse dialing and you need to send DTMF tones during a call
(if you're using an automated response system, for example), press
*
to temporarily switch to tone dialing. When the call ends, the phone
automatically returns to pulse dialing mode.


1.
2.
Charging
contacts
FIND
Charging
contacts
FIND
Earpiece
Display
STATUS
PHONEBOOK/
LEFT CALLER ID/
RIGHT
UP/DOWN
Microphone
12-key dial pad
MESSAGES/
MUTE-CLEAR
END
TALK/
FLASH
MENU/
SELECT
REDIAL/
PAUSE
Earpiece
Display
STATUS
PHONEBOOK/
LEFT CALLER ID/
RIGHT
UP/DOWN
Microphone
12-key dial pad
MESSAGES/
MUTE-CLEAR
END
TALK/
FLASH
MENU/
SELECT
REDIAL/
PAUSE

5
Base key and how it works
 What it does
Find
In standby: page the handset.-
Handset keys/LEDs and how they work
 What it does
Talk/Flash
In standby: start a telephone call (get a dial tone).
During a call: switch to a waiting call.
-
-
End
During a call: hang up.
In the menu or any list: exit and go to standby.
-
-
Up ( )
In standby: increase the ringer volume.
During a call: increase the audio volume.
In any menu or list: move the cursor up one line.
-
-
-
down ( )
In standby: decrease the ringer volume.
During a call: decrease the audio volume.
In any menu or list: move the cursor down one line.
-
-
-
phonEbook/
lEFT ( )
In standby or during a call: open the phonebook.
In the menu: go back to the previous screen.
During text entry: move the cursor to the left.
-
-
-
CallEr id
/righT
In standby or during a call: open the Caller ID list.
During text entry: move the cursor to the right.
-
-
MEnU/
sElECT
In standby: open the menu.
In the menu or any list: select the highlighted item.
-
-
rEdial/
paUsE
In standby: open the redial list.
While entering a phone number: insert a 2-second
pause.
-
-
MEssagEs/
MUTE-ClEar
( )
In standby: access your voice mail service.
During a call: mute the microphone.
If the phone is ringing: mute the ringer for this call
only.
While entering text: Delete the entered text.
-
-
-
-

6
LED What it means
sTaTUs
On: the battery is charging.
Blinking: there are new messages.
-
-
Reading the Display
This table shows possible status icons and what they mean. Since the
icons appear based on what you're doing with the phone, you won't
ever see all of these icons at the same time.
Icon What it means
The ringer is turned off and will not ring for new calls.
You have a voice message waiting.
The microphone is muted; the caller can't hear you.
T-coil mode is on (see page 13).
The battery is 1) fully charged, 2) half charged, 3) getting
low, or 4) empty.
[Aa] [aA] Enter 1) capital or 2) lower case letters (see page 7).
Using the Menu
If you open the
menu during a call,
use lEFT to back out
of the menu without
hanging up.
If you don't press
any keys for about
thirty seconds, the
handset exits the
menu.


Handset Setup
Day & Time
Global Setup
To open the
menu, press
MENU/SELECT.Press MENU/SELECT
to choose the
highlighted option .
press END
to exit the
menu .
To go back a
screen, press
PHONEBOOK/LEFT
The cursor
shows the
highlighted
option.
To move the
cursor, use
UP & DOWN.
OR
<HANDSET SETUP>
T-coil
Ringer Tones
Handset Setup
Day & Time
Global Setup
To open the
menu, press
MENU/SELECT.Press MENU/SELECT
to choose the
highlighted option .
press END
to exit the
menu .
To go back a
screen, press
PHONEBOOK/LEFT
The cursor
shows the
highlighted
option.
To move the
cursor, use
UP & DOWN.
OR
<HANDSET SETUP>
T-coil
Ringer Tones

7
Handset Setup Menu
T-coil Turn on T-coil mode to reduce noise on some hearing
aids (for more details, see page 13).
Ringer Tones
Choose the handset's ring tone. As you highlight each
ring tone, the phone plays a sample. When you hear
the tone you want, press MEnU/sElECT .
AutoTalk Have the handset answer a call when you pick it up
from the cradle (without pressing any buttons).
Any Key
Answer
Have the handset answer a call when you press any
key on the 12-key dialpad.
Handset
Language Change the display language.
Key Touch Tone Have the keypad sound a tone when you press a key.
Day & Time Menu
Use this menu to set the clock manually. (If you have Caller ID, the
phone sets the day and time from the CID data.) Select the day of week,
then use the number keypad to enter the hour and minutes in HHMM
format (e.g., enter 0345 for 3:45). Use Up or down to select AM/PM.
Global Setup Menu
Dial Mode Change the way your phone communicates with the
telephone network (see page 4).
Edit Voice
Mail
Program your voice mail access number so you can get
messages by pressing one button (see page 11).
VMWI Reset Reset your Visual Message Waiting Indicator to bring it
back in sync with your voice mail service.
Entering Text on Your Phone
Use the 12-key dial pad when you want to enter text into your phone
(a name in the phonebook, etc.).
The phone defaults to a capital letter for the first letter and any
letter after a space; otherwise, it uses small letters.


8
To switch to all capital letters, press * . The phone defaults to all
capital letters first (e. g. ABCabc2) until you enter a blank space or
press
*
again. (Any time you want to change case, just press
*
.)
If two letters in a row use the same number key, enter the first letter
and wait a few seconds (or press righT ); the cursor will move to the
next space. Enter the next letter.
Press # to enter a blank space.
To change a letter, move the cursor to that letter and press ClEar to
erase the letter. Then, enter the new letter.
To erase the entire entry, press and hold ClEar .
Press 0 to cycle through all available symbols and punctuation.
USING YOUR PHONE
Basics
To do this... Do this...
make a call Dial the number, then press Talk/Flash .
answer a call Press Talk/Flash .
hang up Press End or put the handset in the cradle.
mute the microphone
during a call
Press MEssagEs/MUTE-ClEar . Press again to
turn the microphone back on.
mute the ringer for this
call only
While the phone is ringing, press MEssagEs/
MUTE-ClEar .
Changing the Volume
Anytime you are listening to the earpiece, press Up to increase the
volume and down to decrease it.
To set the ringer volume: when the phone is in standby, press Up to
increase the ringer volume and down to decrease it. If you turn the
ringer volume all the way down, the ringer turns off.







9
Using the Caller ID and Redial Lists
Caller ID (CID) is a service available from your telephone provider
that shows the phone number (and sometimes the caller’s name) of
incoming calls. Contact your telephone provider for more information.
 
When a call comes in, the phone displays the
number and name (if available) of the caller.
The phone saves the information for the last
30 received calls to the CID list.
When it’s in standby, the handset shows how
many calls came in since the last time you
checked the CID list.
-
-
-
The handset
remembers the
last 5 numbers
you dialed on it.
-
To… 
Open the CID list Press CallEr id/righT .
Open the redial list
rEdial/paUsE.
Scroll through the
lists
Press down to scroll from newest to oldest.
Press Up to scroll from oldest to newest.
Dial a number from
the lists
Highlight the number you want and press
Talk/Flash .*
Close the lists Press phonEbook/lEFT .
* If the number is a toll or long distance call, but there's no 1at the front of
the CID record, press
*
to add the 1before dialing.
To select a number, highlight the number and press MEnU/sElECT . The
phone gives you the following options:
Delete Entry Erase the number from the list.
Store Into Pb Add the number to the phonebook. The handset prompts
you to edit the name and number.
Delete All (CID list only) Erase all numbers from the list.

10
Using Call Waing
Call Waiting, a service available from your telephone provider, lets you
receive calls while you are on another call. Caller ID on Call Waiting
(CIDCW) service displays Caller ID information for a waiting call.
If you get a Call Waiting call, the phone sounds a tone and displays any
CID information received from the waiting call. Press Talk/Flash to
switch between the current call and the waiting call; each time you
switch, there is a short pause before you're connected to the other call.

The phone can store up to 30 entries in its phonebook.
To... Press...
Open/close the phonebook
phonEbook/lEFT.
Scroll through the entries
down (to scroll through the phonebook
from A to Z) or Up (to scroll from Z to A).
Jump to entries that start
with a certain letter
the number key corresponding to the
letter you want.
Dial an entry
Up or down to find the entry you want to
dial, then press Talk/Flash .
Phonebook Menu Opons
Open the phonebook with the phone in standby, then press MEnU/
sElECT to open the phonebook menu. Choose one of these options:
Create New Add an entry to your phonebook. The phone prompts you
to enter a name and number.
Delete All Erase all the entries in the phonebook.
If you need the phone to pause before sending the next set of digits,
press rEdial/paUsE to insert a 2-second pause. The pause shows as a
P in the display.
You can insert as many pauses as you need, but each pause counts
as one of your 20 digits.



11
Phonebook Entry Opons
With the phone in standby, open the phonebook and find the entry
you want. Press MEnU/sElECT to open the individual phonebook entry
menu. The phone prompts you to edit or delete the entry.

With the phone in standby, press Find on the base. The handset will
beep in a 3-beep pattern for 1 minute or until you press Find again.
You can also end the page by pressing any key from the found handset.


If you often have to enter a series of digits or a code number during a
call, you can save that code number to a phonebook entry and use the
phonebook to send the code number.
Enter the code number (up to 20 digits) into the phonebook just
like a regular phonebook entry. Be sure to enter the code number
into the phonebook exactly as you would enter it during a call.
When you hear the prompt that tells you to enter the number,
open the phonebook and find the entry that contains your code
number. Press MEnU/sElECT to transmit the code. The phone
transmits the code number entered in the previous step. If you
change your mind, use phonEbook/lEFT to close the phonebook.

If you subscribe to a voice mail service, your phone can notify you
when you have a new message and give you one-touch access to your
voice mailbox.
To Program Your Access Number
The voice mail company will provide you with the access number.
With the phone in standby, open the menu and select Global Setup.
1.
2.
1.

12
Select Edit Voice Mail.
Enter the access number (up to 20 digits) that your voice mail
provider gave you. Be sure to enter the number exactly as you
would dial it.
When you’re finished, press MEnU/sElECT .
To access your mailbox, just press MEssagEs/MUTE-ClEar when the
phone is in standby. The phone dials the access number exactly as you
entered it.
New Message Nocaon
This feature supports Frequency-Shift Keying (FSK) message
notification. Contact your voice mail provider for more information.
When you have new messages, the voice message icon appears in
the display, and the
STATuS
light on the handset blinks.
After you listen to your messages, the voice message icon turns off.
If it doesn’t, you can reset it: With the phone in standby, open the
menu and select Global Setup; select VMWI Reset, then select Yes.


If you have any trouble with your phone, try these simple steps first. If
you need help, call our Customer Care line listed on the front cover.
If… Try…
I can’t make or receive
calls.
Checking the telephone cord connection.
Disconnecting the base AC adapter. Wait
a few minutes, then reconnect it.
Making sure the base is plugged in.
-
-
-
The handset won’t ring. Making sure the ringer is turned on.-
The handset is not
working.
Charging the battery for 15-20 hours.
Checking the battery connection.
-
-
2.
3.
4.




13
If… Try…
The handset won’t
display CID information.
Letting calls ring twice before answering.
Making sure your CID service is active.
-
-
I hear a beeping during
a call.
The battery is getting low. Check the
handset for a low battery alert. Finish
your conversation and return the handset
to the cradle as soon as possible.
-
Weak or Hard To Hear Audio
If a caller’s voice sounds weak or soft,
the signal might be blocked by large
metal objects or walls; you might
also be too far from the base or the
handset’s battery may be weak.
Try moving around while you’re
on a call or moving closer to
the base to see if the sound gets
louder.
Make sure the handset’s battery is
fully charged.
Try adjusting the earpiece volume.
Noise or �tac on the Lineoise or �tac on the Line
Interference is the most common cause of noise or static on a cordless
phone. Here are some common sources of interference:
electrical appliances, especially microwave ovens
computer equipment, especially wireless LAN equipment and DSL
modems
radio-based wireless devices, such as room monitors, wireless
controllers, or wireless headphones or speakers
fluorescent light fixtures (especially if giving off a buzzing noise)
other services that use your phone line, like alarm systems,
intercom systems, or broadband Internet service









If you have a hearing aid
equipped with a telecoil (T-coil)
feature, the interacon between
the hearing aid & digital cord-
less phones can cause noise
in the handset. If you have a
T-coil hearing aid & you have
problems with noise on the
line, try turning on T-coil mode.
Open the menu. Select Handset
Setup, then select T-coil .
Using T-coil mode can shorten
the handset’s talk me; make
sure to watch the baery status
and keep the baery charged.
•
•

If you have a hearing aid
equipped with a telecoil (T-coil)
feature, the interacon between
the hearing aid & digital cord-
less phones can cause noise
in the handset. If you have a
T-coil hearing aid & you have
problems with noise on the
line, try turning on T-coil mode.
Open the menu. Select Handset
Setup, then select T-coil .
Using T-coil mode can shorten
the handset’s talk me; make
sure to watch the baery status
and keep the baery charged.
•
•

14
 
Check nearby for one of the
common interference sources.
Try moving the handset away
from a suspected source, or try
moving the suspected source so
it’s not between the handset and
the base.
There is always more noise at the
edges of the base's range. If an
Out of Range message displays,
try moving closer to the base.
-
-
-
Check near the base for the
source of interference.
Try moving the base away from
a suspected source, or turn off
the source if possible.
If the base has an adjustable
antenna, try raising the antenna
so it stands straight up.
If you have any service that
uses the phone line, you might
need a filter (see below).
-
-
-
-
Installing a Line Filter or D�L Filter
Sometimes, broadband Internet services that use the telephone line
can interfere with phones. One of these services−DSL−often causes
static on telephones. A DSL filter or telephone line filter usually solves
this problem. The technician who installed your DSL service might
have left some filters for you; if not, call your DSL provider or look in
any electronics store.
Plug the DSL filter into the telephone wall jack and plug your phone’s
base into the filter. Make a test call to make sure the noise is gone.
Liquid Damage
Moisture and liquid can damage your cordless phone.
If the exterior housing of the handset or base is exposed to moisture
or liquid, wipe off the liquid, and use as normal.
If moisture or liquid is inside the plastic housing (i.e. liquid can
be heard in the phone or liquid has entered the handset battery
compartment or vent openings on the base), follow these steps:



15
Handset Base
Remove the battery cover and disconnect
the battery.
Let dry for at least 3 days with the battery
disconnected and the cover off for
ventilation.
After the handset dries, reconnect the
battery and replace the cover. Recharge the
battery fully (15-20 hours) before using.
1.
2.
3.
Disconnect the AC
adapter to cut off
the power.
Disconnect the
telephone cord.
Let dry for at least
3 days before
reconnecting.
1.
2.
3.




Use only the supplied AC
adapters. Be sure to use the
proper adapter for the base &
any chargers.
Do not place the power cord
where it creates a trip hazard
or where it could become
chafed and create a re or electrical hazard.
Do not place the unit in direct sunlight or subject it to high temperatures.
Fully charged, the baery should provide about 10 hours of talk me and about
7 days of standby me. For best results, return the handset to the cradle aer
each call to keep it fully charged.
When the baery gets too low, the handset shows a low baery alert. If you
hear a strange beep during a call, check the display: if you see the low baery
alert, nish your conversaon as quickly as possible and return the handset to
the cradle. If the handset is in standby, none of the keys will operate.
With normal use, the baery should last about one year. Replace the baery
when the talk me becomes short even when the baery is charged. To buy a
replacement baery, call the Parts Department listed on the front cover.

This equipment contains a rechargeable Nickel-Cadmium (Ni-Cd) baery.
•
•
•
•
•
•
•
AC
adapter
Part number PS-0035
Input voltage 120V AC, 60 Hz
Output voltage 8V AC @ 300mA
Baery
pack
Part number BT-1007
Capacity 500mAh, 2.4V DC
AC
adapter
Part number PS-0035
Input voltage 120V AC, 60 Hz
Output voltage 8V AC @ 300mA
Baery
pack
Part number BT-1007
Capacity 500mAh, 2.4V DC

16
Cadmium and Nickel are chemicals known to the State of
California to cause cancer.
Do not short-circuit the baery.
The rechargeable Ni-Cd baeries contained in this equipment
may explode if disposed of in a re.
Do not charge the baery used in this equipment in any charger other than the
one designed to charge this baery as specied in the owner's manual. Using
another charger may damage the baery or cause it to explode.
As part of our commitment to protecng our environment and conserving
natural resources, Uniden voluntarily parcipates in an RBRC
®
industry program
to collect and recycle used Ni-Cd baeries within the United States. Please call 1-
800-8-BATTERY for informaon on Ni-Cd baery recycling in your area. (RBRC
®
is
a registered trademark of the Rechargeable Baery Recycling Corporaon.)


products & accessories.





This equipment complies with Part 68 of the FCC rules and the require-
ments adopted by the ACTA. On the boom of this equipment is a label that
contains, among other informaon, a product idener in the format US:
AAAEQ##TXXXX. If requested, this number must be provided to the phone
company.
An applicable Universal Service Order Codes (USOC) cercaon for the jacks
used in this equipment is provided (i.e., RJ11C) in the packaging with each piece
of approved terminal equipment. A plug and jack used to connect this equip-
ment to the premises wiring and telephone network must comply with the ap-
plicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to
be connected to a compable modular jack that is also compliant. See installa-
on instrucons for details.
The REN is used to determine the number of devices that may be connected
to a phone line. Excessive RENs on a phone line may result in devices not
•
•
•
•
•

17
ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed ve (5.0). To be certain of the number of devices
that may be connected to a line, as determined by the total RENs, contact the
telephone provider. The REN for this product is part of the product idener
that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the telephone network, the telephone
company will nofy you in advance that temporary disconnuance of service
may be required. But if advance noce isn't praccal, the telephone company
will nofy the customer as soon as possible. Also, you will be advised of your
right to le a complaint with the FCC if you believe it is necessary. The tele-
phone company may make changes in its facilies, equipment, operaons or
procedures that could aect the operaon of the equipment. If this happens
the telephone company will provide advance noce in order for you to make
necessary modicaons to maintain uninterrupted service.
Please follow instrucons for repairing, if any (e.g. baery replacement sec-
on); otherwise do not substute or repair any parts of the device except as
specied in this manual. Connecon to party line service is subject to state
taris. Contact the state public ulity commission, public service commission
or corporaon commission for informaon. This equipment is hearing aid
compable.
If you experience trouble with this equipment, contact the manufacturer (see
the cover of this manual for contact informaon) or an authorized agent.
If the equipment is causing harm to the telephone network, the telephone
company may request that you disconnect the equipment unl the problem
is resolved.
If your home has wired alarm equipment connected to a phone line, be sure
that installing the system does not disable your alarm equipment. If you have
quesons about what will disable alarm equipment, contact your telephone
company or a qualied installer.
Any changes or modicaons to this product not expressly approved by the
manufacturer or other party responsible for compliance could void your authority
to operate this product.
NOTICE: According to telephone company reports, AC electrical surges, typi-
cally resulng from lightning strikes, are very destrucve to telephone equip-
ment connected to AC power sources. To minimize damage from these types
of surges, a surge arrestor is recommended.

18

This device complies with part 15 of the FCC rules. Operaon is subject to the
following two condions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interfer-
ence that may cause undesired operaon. Privacy of communicaons may not
be ensured when using this phone.
 Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protecon against
harmful interference in a residenal installaon. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instrucons, may cause harmful interference to radio
communicaons. However, there is no guarantee that interference will
not occur in a parcular installaon. If this equipment does cause harmful
interference to radio or television recepon, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This product complies with FCC radiaon exposure limits under the following
condions:
The base must be placed to allow a minimum of 20 cm (8 inches) between the
antenna and all persons during normal operaon.
The base must not be collocated or operated in conjuncon with any other
antenna or transmier.
The handset is designed for body-worn operaon and meets FCC RF exposure
guidelines when used with any belt clip, carrying case, or other accessory sup-
plied with this product. (All necessary accessories are included in the package;
any addional or oponal accessories are not required for compliance with
the guidelines.) Third party accessories (unless approved by the manufacturer)
should be avoided as these might not comply with FCC RF exposure guidelines.
•
•
•
•
•
•
•

19

Terminal equipment
NOTICE: This equipment meets the applicable Industry Canada TerminalIndustry Canada Terminal
Equipment Technical Specicaons. This is conrmed by the registraon
number. The abbreviaon IC before the registraon number signies that
registraon was performed based on a Declaraon of Conformity indicang
that Industry Canada technical specicaons were met. It does not imply that
Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment
is marked on the equipment itself. The REN assigned to each terminal equip-
ment provides an indicaon of the maximum number of terminals allowed to
be connected to a telephone interface. The terminaon on an interface may
consist of any combinaon of devices subject only to the requirement that the
sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
Radio equipment
The term IC before the radio cercaon number only signies that Industry
Canada technical specicaons were met. Operaon is subject to the follow-
ing two condions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause
undesired operaon of the device. "Privacy of communicaons may not be
ensured when using this telephone".


WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden")
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail
owner, this Uniden Product to be free from defects in materials and crasman-
ship with only the limitaons or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and
be of no further eect 12 months aer the date of original retail sale. The
warranty is invalid if the Product is (A) damaged or not maintained as reason-
able or necessary, (B) modied, altered, or used as part of any conversion
kits, subassemblies, or any conguraons not sold by Uniden, (C) improperly
installed, (D) serviced or repaired by someone other than an authorized
Uniden service center for a defect or malfuncon covered by this warranty,
(E) used in any conjuncon with equipment or parts or as part of any system
not manufactured by Uniden, or (F) installed or programmed by anyone other
than as detailed by the owner's manual for this product.

STATEMENT OF REMEDY: In the event that the product does not conform to
this warranty at any me while this warranty is in eect, warrantor will either,
at its opon, repair or replace the defecve unit and return it to you without
charge for parts, service, or any other cost (except shipping and handling)
incurred by warrantor or its representaves in connecon with the perfor-
mance of this warranty. Warrantor, at its opon, may replace the unit with a
new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE
AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER
EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow this exclusion or limitaon of incidental or conse-
quenal damages so the above limitaon or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specic legal rights, and you may
also have other rights which vary from state to state. This warranty is void
outside the United States of America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, aer follow-
ing the instrucons in the owner's manual you are certain that the Product
is defecve, pack the Product carefully (preferably in its original packaging).
Disconnect the baery from the Product and separately secure the baery
in its own separate packaging within the shipping carton. The Product should
include all parts and accessories originally packaged with the Product. Include
evidence of original purchase and a note describing the defect that has caused
you to return it. The Product should be shipped freight prepaid, by traceable
means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
As an Energy Star
®
Partner, Uniden has determined that this
product meets the Energy Star
®
guidelines for energy eciency.
Energy Star
®
is a U.S. registered mark.
Uniden
®
is a registered trademark of Uniden America Corporaon.
The pictures in this manual are for example only. Your phone may
not look exactly like the pictures.
May be covered under one or more of the following U.S. patents:
7,206,403 7,310,398 7,460,663
Other patents pending.
•
•