UNISEM UniTracer L-100 User manual

www.unisem.co.kr | [e-mail] |+82.31.724.2548
UniTracer
[Electronic locking device for container]
USER MANUAL
FOR UniTracer L-100
This guide explains the device UniTracer L-100.
Version 1
September 2017

www.unisem.co.kr | [e-mail] |+82.31.724.2548
Table of Contents
1. Precautions concerning pre-service..........................................................................................................................3
1.1 Precautions ..................................................................................................................................................................3
1.2 Device package configuration..........................................................................................................................3
1.4 Device installation and sealing method .....................................................................................................6
1.5 How to unseal and retrieve the device.......................................................................................................8
2. How to use the device......................................................................................................................................................9
2.1 Device operating process....................................................................................................................................9
2.2 Insertion of the USIM......................................................................................................................................... 10
2.3 Check battery remaining volume ................................................................................................................ 11
3. Device maintenance ........................................................................................................................................................ 12
3.1 Wire replacement method............................................................................................................................... 12
3.2 USIM replacement method ............................................................................................................................. 12
3.3 How to deal with battery charging/discharging and replacement.......................................... 12
3.4 Device reset method........................................................................................................................................... 12
3.5 APN and NFC setting method....................................................................................................................... 13
4. Trouble Shooting............................................................................................................................................................... 20
4.1 Device debugging method.............................................................................................................................. 20
4.3 Log data analysis method................................................................................................................................ 33
5. Device FAQ ........................................................................................................................................................................... 35

www.unisem.co.kr | [e-mail] |+82.31.724.2548
1. Precautions concerning pre-service
1.1 Precautions
- The battery should be used after full charging. The device connects a 5V 2A adapter to the
USB port using the included USB cable.
- The USIM card should be prepared for local use or roaming in accordance with the purpose
of use.
- Once inserted, it is imperative that the insertion of caution is checked again, because it cannot
be withdrawn again.
- To use an NFC card, you must register the NFC card ID in the L-100 device.
- This device can be operated in at least one Member State of EU without infringing applicable
requirements on the use of radio spectrum.
1.2 Device package configuration
UniTracer L-100 Mini B type USB cable

www.unisem.co.kr | [e-mail] |+82.31.724.2548
- UniTracer L-100 Specification
Item Specifications
Model UniTracer L-100
Temperature -30~+80℃
Humidity 0~99%
Electrical Usage 3.78VDC
CPU 32Bit MPU
Data Storage 1Mbit EEPROM x 2
Data Transmission 792 Times(33 days)
(24 Collections per day, every hour)
Battery Capacity Lithium-Ion
6,000mAh(Rechargeable)
Sensor Open/Close of door, Location,
Detect cutting
GPS GPS
Certifications KC/CE/IP66
Weight 1.5Kg
(Inclusive 500g battery)
Size 75(W) x 140(H) x 40(D)mm
Lock Method Sensor Wire Seal
Identification NFC(ISO 14443 Type A)
Diagnostic Port USB Port
DC Power Input 5V/2A
GSM UL Frequency Band GSM 900 : 880.2 ~ 914.8MHz
DCS 1800 : 1710.2 ~ 1784.8MHz
GSM DL Frequency Band GSM 900 : 925.2 ~ 959.8MHz
DCS 1800 : 1805.2 ~ 1879.8MHz
WCDMA UL Frequency Band 1Band : 1922.4 ~ 1977.6 MHz
8Band : 882.4 ~ 912.6 MHz
WCDMA DL Frequency Band 1Band : 2112.4 ~ 2167.6 MHz
8Band : 927.4 ~ 957.6 MHz
NFC transmit / receive
frequency range 13.56 MHz
GPS receive
frequency range 1559MHz ~ 1610MHz

www.unisem.co.kr | [e-mail] |+82.31.724.2548
1.3 Component parts of the device
⑤Operation Switch
①Lock Wire Cable
②Left Wire Segment
⑥USIM Port
⑦mini B type USB
Port
③Right Wire Segment
④NFC Antenna
⑧Reset Switch

www.unisem.co.kr | [e-mail] |+82.31.724.2548
No. Part Name Description Remarks
1 Lock Wire Cable 30cm, 100cm optional
2 Left Wire Segment The left wire segment is fixed.
3 Right Wire Segment You can hold and open and close the right
wire segment.
4 NFC Antenna Where to tag the NFC card
5 Operation Switch -
Blinking green light for GPS
communication
-
Blinking blue light for WCDMA/GSM
communication
6 USIM Port Port that inserts USIM card
7 mini B type USB Port Port that charges the device and analyzes
the device log
8 Reset Switch Switch to reset the device
1.4 Device installation and sealing method
- With the wire open, wire the device to the container lock and fasten the device.
- When connecting the wire to the device, be sure to push it all the way to prevent the connection
failure.
- Confirm the lock by touching the NFC card registered in the NFC antenna section within
5 seconds after wire tightening.
- Attach the magnet on the back of the L-100 to the flat surface (steel material) of the container
and tighten the device to the container.
- When attaching the L-100 to a container, etc., be sure to install the L-100 in the following
direction to obtain optimal GPS reception.

www.unisem.co.kr | [e-mail] |+82.31.724.2548
<Figure. Device installation Position>
<Figure. actual device installation example>
Skyward
GPS Antenna
- GPS reception rate is the best
when the GPS antenna is pointing
in the sky.

www.unisem.co.kr | [e-mail] |+82.31.724.2548
1.5 How to unseal and retrieve the device
1) The operation switch is not lit when the device is operating. At this time, when the
operation switch is pressed, the NFC antenna lights in blue. (The light is kept in blue for 5
seconds.)
2) Attach the registered NFC card before the blue light on the NFC antenna turns off. (The
blue light is on for 5 seconds.) When the touch is completed, the buzzer sounds and the
NFC antenna turns off. At this time, pull the right wire segment after press it slightly inwards.
When the wire is disconnected, a green light blinks to receive the GPS(to send the device's
open signal). When the green light is off, a blue light will come on for the data
communication. The blue light turns off when data transmission is completed.

www.unisem.co.kr | [e-mail] |+82.31.724.2548
3) Device retrieve method
- Hold the eSeal device with the magnet attached to the container with both hands firmly and
remove it safely.
- Retrieve the device with opened wire device.
2. How to use the device
2.1 Device operating process
1) When the wire is tightened, the NFC card authentication is performed first.
- The LED of the NFC antenna flashes together with a beep for 5 seconds.
- The registered NFC card should be touched to the NFC tag within 5 seconds.
- If the NFC card is authenticated, the alarm is stopped and the LED flashes.
※In order to use NFC card, NFC card ID must be registered in L-100 device.
(Refer to '3.5 APN and NFC setting method’.)
2) When the NFC card authentication is completed, GPS is received. (Takes up to 180 seconds)
- At this time, the Operation switch flashes green.
- When the GPS reception is complete, the green light turns off.
3) Once the GPS reception is complete, access the communication network. (Up to 300 seconds).
- At this time, the Operation switch flashes blue.
- When the device is connected to the network and the data transmission is finished, the
blue light turns off.
4) After the Operation switch light is blinking, the device waits until the next operation.

www.unisem.co.kr | [e-mail] |+82.31.724.2548
2.2 Insertion of the USIM
Open the water-proof cover and insert it into the following directions.
(Once engaged, ensure that the correct tightening is achieved and the correct orientation
is achieved.)
<Figure. Device USIM insertion direction>
< Figure. Actual device USIM insertion example>