Unitronics Vision OPLC V130-33-B1 User manual

Unitronics 1
Vision™ OPLC™ V130-33-B1
Installation Guide
The Unitronics V130-33-B1 offers the following features:
I/O configurations can be added via Expansion Modules.
Available by separate order: Ethernet, additional RS232/RS485, CANbus.
General Description
V130 OPLCs are micro-OPLCs, rugged programmable logic controllers that comprise:
Built-in operating panel containing a 2.4” screen and a keypad
Communications 1built-in serial port: RS232/RS485
Optional—the user may order and install
one or both of the following modules:
-RS232/RS485/Ethernet
-CANbus
Communication Function Blocks include:
SMS, GPRS, MODBUS serial/IP. Protocol
FB enables PLC to communicate with
almost any external device, via serial or
Ethernet communications
I/O Options V130 supports digital, high-speed, analog,
weight and temperature measurement
I/Os via:
I/O Expansion Modules
Local or remote I/Os may be added
via expansion port or CANbus.
Information Mode This mode enables you to:
View & Edit operand values, COM port settings, RTC and screen
contrast/brightness settings
Stop, initialize, and reset the PLC
To enter Information Mode, press the <i> button for several seconds.
Programming
Software,
&Utilities
The Unitronics Setup CD contains VisiLogic software and other utilities.
VisiLogic
Easily configure hardware and write both HMI and Ladder control
applications; the Function Block library simplifies complex tasks
such as PID. Write your application, and then download it to the
controller via the programming cable included in the kit.
Utilities
Includes UniOPC server, Remote Access for remote programming
and diagnostics, and DataXport for run-time data logging.
To learn how to use and program the controller, as well as use utilities such
as Remote Access, refer to the VisiLogic Help system.
Removable
Memory Storage
Micro SD card: store datalogs, Alarms, Trends, Data Tables; export to Excel;
backup Ladder, HMI & OS and use this data to ‘clone’ PLCs.
For more data, refer to the SD topics in the VisiLogic Help system.
Data Tables Data tables enable you to set recipe parameters and create datalogs.

V130-33-B1 Installation Guide
2Unitronics
Additional product documentation is in the Technical Library, located at www.unitronics.com,and on
the Unitronics’ Setup CD.
Technical support is available at the site, and from [email protected]om.
Standard Kit Contents
Vision controller Mounting brackets (x2)
Power supply connector Rubber seal
Battery (installed) Unitronics’ Setup CD
Programming cable + RS232 adapter
Danger Symbols
When any of the following symbols appear, read the associated information carefully.
Symbol Meaning Description
Danger The identified danger causes physical and property damage.
Warning The identified danger could cause physical and property damage.
Caution Caution Use caution.
Before using this product, the user must read and understand this document.
All examples and diagrams are intended to aid understanding, and do not guarantee operation.
Unitronics accepts no responsibility for actual use of this product based on these examples.
Please dispose of this product according to local and national standards and regulations.
Only qualified service personnel should open this device or carry out repairs.
Failure to comply with appropriate safety guidelines can cause severe injury or property damage.
Do not attempt to use this device with parameters that exceed permissible levels.
To avoid damaging the system, do not connect/disconnect the device when power is on.
Environmental Considerations
Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,
moisture or rain, excessive heat, regular impact shocks or excessive vibration, in accordance
with the standards given in the product’s technical specification sheet.
Ventilation: 10mm space required between controller’s top/bottom edges & enclosure walls.
Do not place in water or let water leak onto the unit.
Do not allow debris to fall inside the unit during installation.
Install at maximum distance from high-voltage cables and power equipment.

Vision™ OPLC™
Unitronics 3
Mounting
Dimensions
Panel Mounting
Before you begin, note that the mounting
panel cannot be more than 5 mm thick.
1. Make a panel cut-out measuring
92x92 mm (3.622”x3.622”).
2. Slide the controller into the cut-out,
ensuring that the rubber seal is in place.
3. Push the 2 mounting brackets into their
slots on the sides of the controller as
shown in the figure to the right.
4. Tighten the bracket screws against the
panel. Hold the bracket securely against
the unit while tightening the screw.
5. When properly mounted, the controller
is squarely situated in the panel cut-out
as shown in the figure to the right.

V130-33-B1 Installation Guide
4Unitronics
DIN-rail Mounting
1. Snap the controller onto the DIN
rail as shown in the figure to the
right.
2. When properly mounted, the
controller is squarely situated on
the DIN-rail as shown in the figure
to the right.
Wiring
Do not touch live wires.
Install an external circuit breaker. Guard against short-circuiting in external wiring.
Use appropriate circuit protection devices.
Unused pins should not be connected. Ignoring this directive may damage the device.
Double-check all wiring before turning on the power supply.
Caution
To avoid damaging the wire, do not exceed a maximum torque of 0.5 N·m (5 kgf·cm).
Do not use tin, solder, or any substance on s
tripped wire that might cause the wire strand
to break.
Install at maximum distance from high-voltage cables and power equipment.
Wiring Procedure
Use crimp terminals for wiring; use 26-12 AWG wire (0.13 mm 2–3.31 mm2):
1. Strip the wire to a length of 7±0.5mm (0.250–0.300 inches).
2. Unscrew the terminal to its widest position before inserting a wire.
3. Insert the wire completely into the terminal to ensure a proper connection.
4. Tighten enough to keep the wire from pulling free.
Input or output cables should not be run through the same multi-core cable or share the same wire.
Allow for voltage drop and noise interference with input lines used over an extended distance. Use
wire that is properly sized for the load.
The controller and I/O signals must be connected to the same 0V signal.

Vision™ OPLC™
Unitronics 5
Power Supply
The controller requires an external 12VDC or 24VDC power supply.
Anon-isolated power supply can be used if a 0V signal is connected to the chassis.
Install an external circuit breaker. Guard against short-
circuiting in external wiring.
Double-check all wiring before turning on the
power supply.
Do not connect either the ‘Neutral or ‘Line’ signal of the
110/220VAC to device’s 0V pin.
In the event of voltage fluctuations or non-conformity to
voltage power supply specifications, connect the device
to a regulated power supply.
Earthing the Power Supply
To maximize system performance, avoid electromagnetic interference by:
Mounting the controller on a metal panel.
Earthing the controller’s power supply: connect one end of a 14 AWG wire to the chassis
signal; connect the other end to the panel.
Note: If possible, the wire used to earth the power supply should not exceed 10 cm in length.
However, it is recommended to earth the controller in all cases.
Communication Port
Turn off power before making communications connections.
Caution
Signals are related to the controller’s 0V; the same 0V is used by the power supply.
Always use the appropriate port adapters.
The serial port is not isolated. If the controller is used with a non-isolated external
device, avoid potential voltage that exceeds ± 10V.
Port 1 is type RJ-11 and may be set to either RS232 or RS485 via jumper as shown below.
By factory default, the port is set to RS232, termination ON.
Use RS232 to download programs from a PC, and to communicate with serial devices
and applications, such as SCADA.
Use RS485 to create a multi-drop network containing up to 32 devices.

V130-33-B1 Installation Guide
6Unitronics
Pinouts
The pinouts below show the PLC port signals.
To connect a PC to a port that is set to RS485, remove the RS485 connector, and connect the PC to
the PLC via the programming cable. Note that this is possible only if flow control signals are not used
(which is the standard case).
RS232 RS485** Controller Port
Pin # Description Pin # Description
1* DTR signal 1 A signal (+)
20V reference 2 (RS232 signal)
3TXD signal 3 (RS232 signal)
4RXD signal 4 (RS232 signal)
50V reference 5 (RS232 signal)
6* DSR signal 6 B signal (-)
Pin #1
*Standard programming cables do not provide connection points for pins 1 and 6.
**When a port is adapted to RS485, Pin 1 (DTR) is used for signal A,
and Pin 6 (DSR) signal is used for signal B.
RS232 to RS485 Jumper Settings
The figure to the right shows the jumper
factory default settings, RS232, RS485
termination ON.
Note that in order:
To change the communication
setting to RS485, both
communication standard
jumpers must be moved.
To change the RS485
termination, both termination
jumpers must be moved.
To access the jumpers, you must open the
controller according to the instructions
beginning on page 7.

Vision™ OPLC™
Opening the Controller
Before performing these actions, touch a grounded object to discharge any electrostatic
charge.
Avoid touching the PCB board directly. Hold the PCB board by its connectors.
1. Turn off the power supply, disconnect, and dismount the controller.
2. The back cover of the controller comprises 4 screws, located in the corners. Remove the screws,
and pull off the back cover.
Changing Communication Settings
1. To access the communication
jumpers, hold the Power Supply
PCB by its edges and steadily pull
the board off.
2. Locate the jumpers, and then
change the settings as required.
Jumper settings are shown on
page 6.
Closing the Controller
1. Gently replace the board. Make
certain that the pins fit correctly
into their matching receptacle.
Do not force the board into place;
doing so may damage the
controller.
2. Replace the back cover of the
controller and fasten the corner
screws.
Note: You must replace the back cover securely before powering up the controller.
Samara
tel. [phone]
[email protected]
Yekaterinburg
tel. [phone]
[email protected]
St. Petersburg
tel. [phone]
[email protected]
Moscow
tel. [phone]
[email protected]
Helsinki
tel. [phone]
automation@klinkmann.
Vilnius
tel. [phone]
[email protected]
Riga
tel. [phone]
[email protected]
Мinsk
tel. [phone]
[email protected]
Tallinn
tel. [phone]
[email protected]
Кiev
tel. [phone]
[email protected].ua