UNITY Lasers ELITE 2 PRO User manual

USER MANUAL
ELITE 2 PRO | ELITE 3 PRO
ELITE 5 PRO | ELITE 10 PRO
Notice
AVOID EYE OR SKIN EXPOSURE TO
DIRECT OR SCATTERED LIGHT
CLASS 4 LASER PRODUCT
Manufactured/ Certified by
UNITY Lasers s.r.o.
Odborárska 23
831 02 Bratislava
Slovakia, Europe
Classified per IEC 60825-1 2014
Complies with US FDA CDRH laser safety
standards 21 CFR 1040.10 & 1040.11
and Laser notice 50

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
2
Contents
INTRODUCTION 3
WHAT IS INCLUDED 3
UNPACKING INSTRUCTIONS 3
GENERAL INFORMATION 3
SAFETY NOTES 4
LASER AND SAFETY NOTES 5
PRODUCT SAFETY LABEL LOCATION 7
PRODUCT SAFETY LABELS 8
INTERLOCK CONNECTION DIAGRAM 9
INSTRUCTIONS FOR USING E-STOP SYSTEM 11
THEORY OF OPERATION 12
PROPER USAGE 12
RIGGING 12
OPERATION 13
SAFETY TESTS 15
E-STOP FUNCTION 15
INTERLOCK RESET FUNCTION (POWER) 15
KEY SWITCH FUNCTION 15
MODEL SPECIFICATIONS 16
ILDA PINOUT SPECIFICATION 28
TECHNICAL INFORMATION –MAINTENANCE AND SERVICE 29
MAINTENANCE 29
SERVICE 32

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
3
INTRODUCTION
Thank you for purchasing your purchase. To optimize the performance of your laser, please read these
operating instructions carefully and familiarize yourself with the basic operations of this system. These
instructions contain important safety information regarding the use and maintenance of this system as well.
Please keep this manual with the unit, for future reference. If you sell this product to another user, be sure
that they also receive this document.
Notice
We are constantly striving to improve the quality of our products. As such, the content of this
manual may be changed without notice.
We have tried our best to guarantee the accuracy of this manual. If you have any questions or find
any errors, please contact us directly to help address this.
WHAT IS INCLUDED
NAME
PCS
Remark
Elite Pro Laser
1
Control cable ILDA 10m
1
Power cord AC 1,5m
1
Keys for Projector key switch
2
Keys for E-stop box
2
E-stop Box
1
E-stop box connecting cable 10m
1
Remote interlock bypass 3pin
1
User guide
1
UNPACKING INSTRUCTIONS
Open the package and carefully unpack everything inside.
Ensure all parts are present and in good condition.
Do not use any equipment that appears to be damaged.
If any parts are missing or damaged then please immediately notify your carrier or local distributor.
GENERAL INFORMATION
The following chapters explain important information about lasers in general, basic laser safety and
some tips about how to use this device correctly. Please read this information as it contains critical
information you must be aware of, prior to using this system.

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
4
SAFETY NOTES
WARNING! This projector is a Class 4 laser product. It must never be used for audience-scanning
applications. The output beam of the projector must always be at least 3 meters above the floor in the
audience. See the Operating Instructions section for further information.
Please read the following notes carefully! They include important safety information about the
installation, usage, and maintenance of this product.
Keep this User Manual for future consultation. If you sell this product to another user, be sure that they also receive this
document.
Always make sure that the voltage of the outlet to which you are connecting this product is within the range stated on
the decal or rear panel of the product.
This product is not designed for use outdoors in adverse weather conditions. To prevent risk of fire or shock, do not
expose this product to rain or moisture.
Always disconnect this product from the power source before cleaning it or replacing the fuse.
Make sure to replace the fuse with another of the same type and rating.
If mounting it overhead, always secure this product to a fastening device using a safety chain or cable.
In the event of a serious operating problem, stop using the projector immediately. Never try to repair the unit except in
a controlled environment under trained supervision. Repairs carried out by unskilled people can lead to damage or
malfunction of the unit, as well as exposure to dangerous laser light.
Never connect this product to a dimmer pack.
Make sure the power cord is not crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Never carry a product from the power cord or any moving part. Always use the hanging/mounting bracket or the
handles.
Always avoid eye or skin exposure to direct or scattered light from this product.
Lasers can be hazardous and have unique safety considerations. Permanent eye injury and blindness is possible if lasers
are used incorrectly. Pay close attention to each safety REMARK and WARNING statement in this user manual. Read all
instructions carefully BEFORE operating this device.
Never intentionally expose yourself or others to direct laser light.
This laser product can potentially cause instant eye injury or blindness if laser light directly strikes the eyes.
It is illegal and dangerous to shine this laser into audience areas, where the audience or other personnel could get direct
laser beams or bright reflections into their eyes.
It is a US Federal offense to shine any laser at aircraft.
No service allowed by customer. There are no user serviceable parts inside the unit. Do not attempt any repairs
yourself.
Service is only to be handled by the factory or authorized factory trained technicians.
Product is not to be modified by the customer.
Caution –use of controls or adjustments or performance of procedures other than those specified herein may result
in hazardous radiation exposure.

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
5
LASER AND SAFETY NOTES
STOP AND READ ALL THE LASER SAFETY NOTES BELOW
Laser Light is different from any other light sources with which you may be familiar. The light from this
product can cause eye and skin injury if not set up and used properly. Laser light is thousands of times
more concentrated than light from any other kind of light source. This concentration of light can cause
instant eye injuries, primarily by burning the retina (the light sensitive portion at the back of the eye). Even
if you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your audience. Even
very small amounts of laser light are potentially hazardous even at long distances. Laser eye injuries can
happen quicker than you can blink. It is incorrect to think that because these laser entertainment products
use high speed scanned laser beams, that an individual laser beam is safe for eye exposure. It is also
incorrect to assume that because the laser light is moving, it is safe. This is not true.
Since eye injuries can occur instantly, it is critical to prevent the possibility of any direct eye exposure. It is
not legal to aim this laser projector into areas where people can be exposed. This is true even if it is aimed
below people’s faces, such as on a dance floor.
Do not operate the laser without first reading and understanding all safety and technical data in this
manual.
Always set up and install all laser effects so that all laser light is at least 3 meters (9.8 feet) above the
floor on which people can stand. See the “Proper Usage” section later in this manual.
After set up, and prior to public use, test the laser to ensure proper function. Do not use if any
defect is detected.
Laser Light - Avoid Eye or Skin Exposure to Direct or Scattered Light.
Do not point lasers at people or animals.
Never look into the laser aperture or laser beams.
Do not point lasers in areas where people can potentially be exposed, such as uncontrolled
balconies, etc.
Do not point lasers at highly reflective surfaces, such as windows, mirrors and shiny metal objects.
Even laser reflections can be hazardous.
Never point a laser at aircraft, as this is a US Federal offense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use the laser if the housing is damaged, open, or if the optics appear damaged in any way.
Never leave this device running unattended.
In the United States, this laser product may not be purchased, sold, rented, leased or loaned for
use unless the recipient possesses a valid Class 4 laser light show variance from the US FDA CDRH.
This product must always be operated by a skilled and well-trained operator who is familiar with the
data included in this manual. Note that use of this projector in the United States also requires a
valid Class 4 laser light show variance from the CDRH as stated above.
The legal requirements for using laser entertainment products vary from country to country. The
user is responsible for the legal requirements at the location/country of use.
Always use appropriate lighting safety cables when hanging this projector overhead.

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
6
LASER EMISSION DATA
Class 4 Laser Projector - Avoid Eye and Skin Exposure to Direct or Scattered Light!
This Laser Product is designated as Class 4 during all procedures of operation.
Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1
Standard “For Safe Use of Lasers”, available from the Laser Institute of America:
www.laserinstitute.org. Many local governments, corporations, agencies, military and others,
require all lasers to be used under the guidelines of ANSI Z136.1.
LASER LIGHT COMPANY LLC.
Laser Classification Class 4
Red Laser Medium AlGaInP, 639 nm, depending on model
Green Laser Medium InGaN, 520-525 nm, depending on model
Blue Laser Medium InGaN, 445 nm to 465 nm depending on model
Beam Diameter <10 mm at aperture
Divergence (each beam) <2 mrad
Maximum total output power 2 - 11,5 W, depending on model
LASER COMPLIANCE STATEMENT
This laser product complies with FDA performance standards for laser products except for
deviations pursuant to Laser Notice No. 50, dated June 24, 2007. This laser device is classified as a
Class 4 demonstration laser product.
No maintenance is required to keep this product in compliance with laser performance standards.

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
7
PRODUCT SAFETY LABEL LOCATION
FRONT PANEL
1. Aperture Label
2. Hazard Warning Symbol
3. Interlocked Housing Label (duplicate label found on underside of top panel)
TOP PANEL
4. Aircraft Warning Label
5. Logotype Danger Label
6. Manufacturer Label
7. Certification Label
See next page for large reproductions of the product labels. All these labels must be intact and legible
prior to using the projector.

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
8
PRODUCT SAFETY LABELS
Logotype Danger Label
Hazard Warning Symbol
Aperture Label
Aircraft Warning Label

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
9
Manufacturer Label
Certification Label
Interlocked Housing Label

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
10
Interlock Connection Diagram

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
11
INSTRUCTIONS FOR USING E-STOP SYSTEM
Connect the ESTOP box to the 3-pin interlock connector on the rear of the laser projector using a 3-PIN XLR
cable.
**Note that the E-Stop box has an available secondary interlock port. The secondary port is to be used to interface a secondary
interlock device (e.x. door switch or pressure sensitive step pad). If a secondary interlock device is NOT used then the secondary
port must have the bypass shunt plug inserted.
The diagram below outlines the pinout configuration for the 3-pin connection from ESTOP BOX to the rear
of the projector.

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
12
Theory of operation
"UNITY Laser projector" is supplied with "E-Stop Box" and "Remote Interlock bypass" including one cable. If
user doesn't need aditional "User E-Stop Switch", "Remote Interlock bypass" should be insterted into
"Remote Interlock Connector" on "E-Stop Box". If the user would like to use aditional "User E-Stop Switch",
"Remote Interlock bypass" should be removed from "User E-Stop Connector" on "E-Stop Box". If the „User
E-Stop switch“ is used, then laser emission is ONLY possible, when it is in CLOSED state, and also all other
safety features are satisfied (e.g. mushroom switch, keyswitches, scanfail safety, ...)
PROPER USAGE
This product is for overhead mounting only. For safety purposes, this projector should be mounted on
steady elevated platforms or sturdy overhead supports using suitable hanging clamps. In all cases, you must
use safety cables.
International laser safety regulations require that laser products must be operated in the fashion illustrated
below, with a minimum of 3 meters (9.8 ft.) of vertical separation between the floor and the lowest laser
light vertically. Additionally, 2.5 meters of horizontal separation is required between laser light and
audience or other public spaces.
The audience area can be passively protected by sliding the aperture cover plate upwards and fixing it in
proper position by the two thumb screws.
RIGGING
Be sure that the structure onto which you are mounting this product can support its weight.
Mount the product securely. You can do this with a screw, a nut, and a bolt. You may also use a
mounting clamp if rigging this product onto a truss. The U-shaped support bracket has three
mounting holes which may be used to secure the clamps to the projector.
When mounting this product overhead, always use a safety cable.
Always consider ease of access to the unit before deciding on a location for this product
3 meters
Projector
Beams

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
13
Caution –use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
This Laser Product is designated as Class 4 during all procedures of operation.
REMINDER: In the United States, this laser product may not be purchased, sold, rented, leased or loaned
for use unless the recipient possesses a valid Class 4 laser light show variance from the US FDA CDRH.
OPERATION
INSTRUCTIONS FOR POWERING ON THE LASER SYSTEM
1. Connect power cable and E-stop.
2. Connect the 3-pin Interlock cable between the E-stop box and projector, pull up the red mushroom switch and
turn on the key switch. Press the start button. Confirm secondary estop port has either the bypass plug installed
or a secondary interlock device attached.
3. Connect the DB25 ILDA cable(s) to the projector. Then connect to any laser software box (for example
Pangolin QuickShow FB3 or FB4 hardware), and then select the pattern on software. Notice; please choose
“Allow laser output” in software.
See the next page for demonstration photos.

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
14
INSTRUCTIONS FOR TURNING OFF THE LASER SYSTEM
1. Turn off the key switch; and deactivate via the red mushroom switch on the E-stop box. You can remove the
3-Pin interlock box too, if the laser will be kept for no use. (We recommend having a professional operator to
keep the keys and 3-Pin interlock switch.)
2. Turn off the power to the projector via the power switch.

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
15
SAFETY TESTS
The following tests MUST be performed each time the projector is used.
Before performing these tests, verify that the projector is facing a safe direction (away from all people
and reflective objects) and aimed at a suitable termination surface.
E-STOP FUNCTION
With the projector operating and projecting laser light, press the red E-stop switch. The projector
must shut off immediately.
Fully extend the red E-stop switch, until a yellow collar is visible on the switch stem. The projector
must not emit any laser light.
Press the start button on E-stop box. The projector should now re-start and begin emitting laser
light.
Verify that the emission indicator is now lit.
INTERLOCK RESET FUNCTION (POWER)
With the projector operating and projecting laser light, unplug the AC power cable. The projector
must shut off immediately.
Plug the power cable back in. The projector must not emit any laser light.
Press the start button on the E-stop box. The projector should now re-start and begin emitting laser
light.
Verify that the emission indicator is now lit.
KEY SWITCH FUNCTION
With the projector operating and projecting laser light, turn the key switch on the remote E-stop
control unit to off. The projector must shut off immediately.
Turn the key switch back to on. The projector must not emit any laser light.
Press the start button on the E-stop box. The projector should now re-start and begin emitting laser
light.
Verify that the emission indicator is now lit.
If any of the above tests fail, the projector must be taken out of service and returned to the
manufacturer for repair.

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
16
MODEL SPECIFICATIONS:
Product Specification (Elite 2 PRO)
Type of laser:
full-colour, semiconductor diode laser system
Guaranteed optical output:
2,100mW
Suitable for:
small to medium indoor / outdoor laser shows and laser graphic
displays
Control signal:
Pangolin FB4 - Ethernet, ArtNet, DMX, ILDA out | PC, Lighting
Console, Autoplay
Scanning system:
35,000 points per second @ 8°
Scan angle:
50°
Safety:
fully complies with the latest EN 60825-1, and FDA regulations
Weight:
8 kg
Package Includes:
Heavy duty flight case, power cord, 10m ethernet (rj45) signal cable,
E-STOP box with 10m cable, set of 4 safety keys, remote interlock
bypass, Pangolin QuickShow laser control and creation software is
available for download.
R | G | B [mw]:
500 | 500 | 1000
Beam size [mm]:
5 x 3
Beam divergence:
<1mrad [full angle]
Modulation:
Analog 100 kHz
Power requirements:
100-230V/50Hz
Consumption:
max. 150W
Operation temperature:
10-40 °C
Ingress rating:
IP 20
System features:
All the adjustments such as power output of each colour, X & Y axes
invert, X & Y size and position, etc. are managed by inbuilt FB4
control system. Scanning system protection, daisy chain of
emergency STOP signal for multiple system "one-hit" operation,
internal fuse.
Laser safety features:
Keyed interlock, emission delay, magnetic interlock, scan-fail safety,
mechanical shutter, adjustable aperture masking plate.
Notice:
*Due to Advanced Optical Correction technology used in our laser
systems the optical power output of each laser colour within the
system may slightly differ from the specification of respective laser
module(s) installed. This does not affect the total guaranteed power
output.
Dimensions [cm]:
Length: 238
Width: 246
Height: 175

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
17
Front & Rear panel view (Elite 2 PRO)
NO.
Name
Function
1
Laser aperture
Laser output, do not look directly into this aperture
2
Aperture masking
plate
Can be moved up and down when two locking bolts are loosened. The
masking plate can also be attached to the top of the aperture.
3
Laser emission
When this indicator is lit up the laser system is ready to emit the laser
radiation as soon as it receives instructions from control software.
4
3-Pin Interlock
Laser output is available only when the interlock is connected.
It could be used to connect a laser emergency switch.
5
Key switch
Turn the key switch ON to allow laser output.
6
Power ON/OFF
Power on/off
7
Fuse
Current rating 3.15A, slow acting type.
8
Power in & out
AC100~240V power input and output sockets. With output feature you
can connect the device to one another using the input and output
sockets. They must be the same fixtures. DO NOT mix fixtures.
9
DMX Input/Through
Use these ports to connect DMX control signal or to daisy chain the
DMX signal between multiple laser display systems.
10
FB4 laser control
interface
11
DB25 OUT
DB25 interface out for ILDA mode
12
Safety eyelet
Use this together with appropriate safety wire to secure the system
against unexpected fall.

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
18
Dimension details (Elite 2 PRO)

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
19
Product Specification (Elite 3 PRO)
Type of laser:
full-colour, semiconductor diode laser system
Guaranteed optical output:
3,100mW
Suitable for:
small to medium indoor / outdoor laser shows and laser graphic
displays
Control signal:
Pangolin FB4 - Ethernet, ArtNet, DMX, ILDA out | PC, Lighting
Console, Autoplay
Scanning system:
35,000 points per second @ 8°
Scan angle:
50°
Safety:
fully complies with the latest EN 60825-1, and FDA regulations
Weight:
8 kg
Package Includes:
Heavy duty flight case, power cord, 10m ethernet (rj45) signal cable,
E-STOP box with 10m cable, set of 4 safety keys, remote interlock
bypass, Pangolin QuickShow laser control and creation software is
available for download.
R | G | B [mw]:
650 | 700 | 1750
Beam size [mm]:
2 x 4
Beam divergence:
<1mrad [full angle]
Modulation:
Analog 100kHz
Power requirements:
100-230V/50Hz
Consumption:
max. 150W
Operation temperature:
10-40 °C
Ingress rating:
IP 20
System features:
All the basic system settings and adjustments such as power output
adjustment for each colour, X & Y axes invert, X & Y size and
position, etc. are managed via built-in FB4 control interface, internal
fuse.
Laser safety features:
Keyed interlock, emission delay, magnetic interlock, scan-fail safety,
mechanical shutter, adjustable aperture masking plate.
Notice:
*Due to Advanced Optical Correction technology used in our laser
systems the optical power output of each laser colour within the
system may slightly differ from the specification of respective laser
module(s) installed. This does not affect the total guaranteed power
output.
Dimensions [cm]:
Length: 238
Width: 246
Height: 175

UNITY Lasers s.r.o. Elite Pro series Operation Manual (Revision 2020-7)
20
Front & Rear panel view (Elite 3 PRO)
NO.
Name
Function
1
Laser aperture
Laser output, do not look directly into this aperture
2
Aperture masking
plate
Can be moved up and down when two locking bolts are loosened. The
masking plate can also be attached to the top of the aperture.
3
Laser emission
When this indicator is lit up the laser system is ready to emit the laser
radiation as soon as it receives instructions from control software.
4
3-Pin Interlock
Laser output is available only when the interlock is connected.
It could be used to connect a laser emergency switch.
5
Key switch
Turn the key switch ON to allow laser output.
6
Power ON/OFF
Power on/off
7
Fuse
Current rating 3.15A, slow acting type.
8
Power in & out
AC100~240V power input and output sockets. With output feature you
can connect the device to one another using the input and output
sockets. They must be the same fixtures. DO NOT mix fixtures.
9
DMX Input/Through
Use these ports to connect DMX control signal or to daisy chain the
DMX signal between multiple laser display systems.
10
FB4 laser control
interface
11
DB25 OUT
DB25 interface out for ILDA mode
12
Safety eyelet
Use this together with appropriate safety wire to secure the system
against unexpected fall.