Universal Electronics ATLAS CABLE 4-DEVICE User manual

ATLAS CABLE 4-DEVICE
Universal Remote Control
(Control Remoto Universal)
User’s Guide
(Guía Del Usuario)
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 1

TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features And Functions . . . . . . . . . . . . . . . . . . . . . . . . 4
Key Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programming Device Control . . . . . . . . . . . . . . . . . . . 8
Programming TV/VCR Combo Control. . . . . . . . . . . . 10
Searching For Your Code . . . . . . . . . . . . . . . . . . . . . . 11
Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . . . 12
Programming ID Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programming Channel Control Lock. . . . . . . . . . . . . 14
To De-Activate Channel Control Lock . . . . . . . . . . . . . . . . . 14
To Re-Activate Channel Control Lock . . . . . . . . . . . . . . . . . 14
Using The Master Power Key . . . . . . . . . . . . . . . . . . . 15
To Program The Master Power Key . . . . . . . . . . . . . . . . . . . 15
To Clear The Master Power Key. . . . . . . . . . . . . . . . . . . . . . 15
To Operate The Master Power Key. . . . . . . . . . . . . . . . . . . . 15
Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . . . 16
Using Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Example – Programming A Favorite Channel . . . . . . . . . . 17
To Clear A Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . . 18
To Unlock Volume Control For A Single Device
(Individual Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . 18
To Unlock All Volume Control
(Global Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
To Lock Volume Control To One Mode
(Global Volume Lock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Instructions To The User . . . . . . . . . . . . . . . . . . . . . . . . . 21
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . 21
Guía Del Usuario. . . . . . . . . . . . . . . . . . . . . . . . . . 22
Manufacturer’s Codes . . . . . . . . . . . . . . . . . . . . . . 42
Setup Codes for Audio Amplifiers. . . . . . . . . . . . . . . . . . . . 42
Setup Codes for Audio Receivers . . . . . . . . . . . . . . . . . . . . 42
Setup Codes for Cable Converters . . . . . . . . . . . . . . . . . . . 43
Setup Codes for DVD Players . . . . . . . . . . . . . . . . . . . . . . . 43
Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Setup Codes for TV/VCR Combos . . . . . . . . . . . . . . . . . . . . 48
Setup Codes for VCRs and PVRs . . . . . . . . . . . . . . . . . . . . 48
2
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 2

INTRODUCTION
The Atlas Cable 4-Device Universal Remote Control by
Universal Electronics is our latest generation universal
remote control. Its sophisticated technology allows you to
consolidate all of your original home entertainment remote
controls into one easy-to-use product.Moreover,it’s packed
with advanced features such as:
• Preprogrammed to operate the cable converter
supplied by your cable system provider
• Master Power key for master on/off control of all of
your equipment with a single keystroke
• Macro key for instant tune-in of favorite channels
• Cable ID Lock to lock your remote control for use only
with the cable converter
• Channel Lock to lock channel selection only to the
cable converter
• Volume Lock to lock volume controls to one mode or
individual modes
• Device Key Re-Assignment to remotely control
a second (duplicate) device
• Color-coded keys to quickly locate popular functions
• Code library for popular video and audio devices
Before using the product, you will need to program it to
operate the specific home entertainment devices you wish
to control.Follow the instructions detailed in this manual
to set up your unit and then start enjoying your new
remote control.
3
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 3

FEATURES AND FUNCTIONS
Use the illustration below to locate features on the Atlas
Universal Remote Control and then study the Key Charts (on
the next two pages) to learn how they function.
4
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 4

Key Charts
Use SETUP for all programming
sequences.
Press POWER once to turn on or off
a home entertainment device.
Press AUD,VCR,TV,orCBL once
to select a home entertainment
device to control. Each device key
has an embedded LED (red light)
that blinks upon selection and
indicates that the remote control is
working and is sending signals.
Use GUIDE to display the program
guide.
Press MENU once to display the
available interactive services.
or
Press LOCK once to lock or unlock
channels for parental control of
viewing.
Use INFO to display the current
channel and program information.
Use SETTINGS/MENU to access
additional cable features (see your
cable converter’s manual).
Use PAGE+ (or PAGE-) to page up
(or page down) through menu
screens and the program guide.
Use the Cursor keys to move the
cursor in the program guide and
menu screens and to navigate
within the interactive service.
Use SELECT to choose options,PPV
events, and to tune programs from
the program guide.
continued on the next page...
5
or
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 5

FEATURES AND FUNCTIONS
Key Charts (continued)
After programming, press MACRO
once to run a macro (see Using
Macros on page 17).
Use EXIT to exit out of your cable
converter’s menu and guide.
Use A,B,orCto access additional
cable features (see your cable
converter’s manual).
Use DAY+ (or DAY-) to move a day
forward (or back) on your cable
converter’s program guide.
Use VOL+ (or VOL-) to raise (or
lower) the audio volume.
Press LAST once to recall the last
channel. For PVRs, use LAST to
select live or recorded video.
Use FAV to cycle through your
favorite channels stored in your
cable converter.
Press MUTE once to turn the sound
off or on.
Use CH+ (or CH-) to select the
next higher (or lower) channel.
For DVD players,use these keys to
skip forward (or reverse) through
chapters. For amplifiers/receivers,
use these keys to select the next
higher (or lower) preset station.
Use the keypad (1~9,0,,and)
to directly select channels (e.g.,09).
Press ENTER once after entering
channel numbers on some TVs.
For amplifiers/receivers, use the
keypad to select inputs 1 through 10.
Use BYPASS to view other video
sources (A or B) instead of cable.
6
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 6

Use TV/VCR to switch the TV input
to view video or TV programs. For
amplifiers/receivers,use this key to
select input or output.
In all modes except CBL, use these
keys to control aVCR, DVD player,
or PVR.To record in the VCR
mode, press REC twice.
In the CBL mode,use these keys
except REC to control VOD (Video
On Demand), if available.
INSTALLING BATTERIES
1. On the back of the remote control, push the tab
and lift off the battery cover.
continued on next page...
7
❶
❸
❷
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 7

INSTALLING BATTERIES (continued)
2. Obtain two (2) new AA alkaline batteries.
Match the + and – marks with those in the
battery case, then insert the new batteries.
3. Align the cover’s keys with the case’s holes and
press the cover back into place.The tab should
click when the cover is locked.
4. Test the unit by pressing POWER and any mode
key (e.g., TV). If batteries are inserted correctly,
the selected mode key will blink once.
NOTE: When batteries need replacement, the remote control will
cease to operate. Replace the batteries and the unit will be restored
to its full functionality, complete with your favorite settings.
PROGRAMMING DEVICE CONTROL
The Atlas Universal Remote Control is preprogrammed to
operate the cable converter provided by your cable system,
an RCA TV, an RCAVCR, and a Pioneer audio receiver.
To control devices other than the default brands,perform
the following steps; otherwise skip this section:
NOTES: To control a DVD player, program the VCR key. To control
a PVR, program the VCR key. To control a stereo amplifier or
receiver, program the AUD key. For TV/VCR Combo control, skip
this section and perform the instructions on page 10.
If you have another brand of cable converter and interactive
service you would like to control, you’ll first need to unlock the
cable ID Lock before changing the converter code – see
“Programming ID Lock” on page 13.
1. Turn on a device and, if applicable, insert video
media, (e.g., cassette or disc).
NOTE: Please read steps 2 to 4 completely before pro-
ceeding. Highlight or write down the codes and device
you wish to program before moving on to step 2.
2. On the remote control,press a device key once
(e.g., AUD,VCR,TV,orCBL). Press and hold
SETUP until the selected mode key blinks
twice, then release SETUP.
3. Use the Manufacturer’s Codes (starting on
page 42) to locate the the type of device and
brand name and then enter the first four-digit
code for your device.If performed correctly, the
selected mode key will blink twice.
8
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 8

NOTE: If the selected mode key emits a long blink, the
code is invalid. Repeat steps 2 and 3 and try entering
the same code again.
4. Aim the remote control at the device and press
POWER once. The device should turn off. If it
does not,repeat steps 2 to 3, trying each code
for your brand until you find one that works.
If it still does not work, try searching for the
code (see Searching For Your Code on page 11).
NOTE: If the device does not have a POWER key, press
the (Play) key.
5. Repeat steps 1 through 4 for each device you
want the the remote control to control. For
future reference, write down each working
device code in the following boxes:
AUD
Audio Device ____________________
VCR
TV
CBL
9
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 9

PROGRAMMING TV/VCR COMBO CONTROL
If you own a TV/VCR Combo,perform the following
instructions to control this device:
1. Turn on your TV/VCR Combo and insert a
video cassette.
2. On the remote control, press VCR once.
Press and hold SETUP until the VCR key
blinks twice, then release SETUP.
3. Use the Setup Codes For TV/VCR Combos (on
page 48) to locate the brand name and then
enter the first four-digit code for your TV/VCR
Combo. If you perform this procedure correctly,
the VCR key will blink twice.
NOTE: If the VCR key did not blink twice after enter-
ing the code’s last digit, then repeat steps 2 to 3 and
try entering the same code again.
If you’ve located a TV/VCR setup code that
works your TV/VCR Combo and a separate TV
code is also listed,you’ll need to program this
code into the remote control to access volume
control (see Programming Device Control on
page 8).
4. Aim the remote control at your TV/VCR
Combo and press POWER once. The device
should turn off. If it does not respond,repeat
steps 2 and 3 (starting on the previous page),
trying each code listed for your brand until you
find one that works.If it still does not work, try
searching for the code (see Searching For Your
Code on the next page).
5. For future reference,write down each working
device code in the boxes below:
TV/VCR
TV (if used)
10
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 10

11
SEARCHING FOR YOUR CODE
If your home entertainment device does not respond to
the Atlas Universal Remote Control after trying all of the
codes listed for your brand, or if your brand is not listed
at all,try searching for your code.
NOTE: To search for a code in the CBL mode, you’ll first need to
unlock the cable ID Lock – see “Programming ID Lock” on
page 13.
For example, to search for a code for your TV:
1. Turn on your TV.
2. On the remote control, press TV once.
Then press and hold SETUP until the
TV key blinks twice, then release SETUP.
3. Enter 9- 9- 1.TheTV key will blink twice.
4. Aim the remote control at the the TV and slowly
alternate between pressing POWER and TV.
Stop when the TV turns off.
NOTE: In the search mode, the remote control will
send IR codes from its library to the selected
device, starting with the most popular code first.
5. Press SETUP once to lock in the code. The TV
key will blink twice.
6. To search for the codes of your other devices,
repeat steps 1 through 5,but substitute the
appropriate key (i.e.,AUD,VCR,orCBL) for
the (Audio,VCR, or Cable) device you are
searching for.
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 11

12
CHECKING THE CODES
If you have set up the Atlas Universal Remote Control
using the Searching For Your Code procedure (on the
previous page), you may need to find out which four-digit
code is operating your equipment.For example,to find
out which code is operating your TV:
1. On the remote control, press TV once.
Then press and hold SETUP until the
TV key blinks twice, then release SETUP.
2. Enter 9- 9- 0.TheTV key will blink twice.
3. To view the code for the first digit,press 1once.
Wait 3 seconds and count the number of times
the TV key blinks (e.g., 3 blinks = 3) and write
down the number in the leftmost TV Code box
(see below).
NOTE: If a code digit is “0”, the selected mode key will
not blink.
4. Repeat step 3 three more times for remaining
digits. Use 2for the second digit,3for the third
digit, and 4for the fourth digit. Finish writing
down the code in the TV Code boxes below.
5. To check for other device codes,repeat steps 1
through 4,but substitute the appropriate key
(i.e., AUD,VCR,orCBL) for the (Audio,VCR, or
Cable) device you are checking.Write down the
codes in the appropriate boxes below.
AUD
Audio Device ____________________
VCR
TV
CBL
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 12

13
PROGRAMMING ID LOCK
The Atlas Universal Remote Control is preprogrammed
and locked at the factory to operate a Scientific Atlanta
cable converter.
However, if you have another brand or model of cable
converter and interactive service that you would like to
control, then you’ll need to perform the following steps to
unlock the cable ID Lock,enter in a new manufacturer’s
code,and lock the ID Lock again.
1. Turn on the cable converter.
2. On the remote control, press CBL once.
Then press and hold SETUP until the
CBL key blinks twice, then release SETUP.
3. Enter 9- 8- 2.TheCBL key will blink
four times.
4. Perform the instructions in Programming
Device Control on page 8 to program device
control for the desired cable converter and
interactive service. Upon completion, perform
the remaining steps (5 and 6 on this page) to
again lock the ID lock.
5. On the remote control, press CBL once.
Then press and hold SETUP until the
CBL key blinks twice, then release SETUP.
6. Enter 9- 8- 2.TheCBL key will blink twice.
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 13

14
PROGRAMMING CHANNEL CONTROL LOCK
By default,the remote control’s channel-control capabilities
are locked to the cable converter. The affected keys* are
0~9,CH+,CH-,ENTER,andLAST.This will guarantee that
you do not inadvertently change a channel on your TV or
VCR. However, you can de-activate this feature to allow full
access to these keys in the TV and VCR modes.
*NOTE: This feature does not affect the AUD mode.
To De-Activate Channel Control Lock:
1. On the remote control, press CBL once.
Then press and hold SETUP until the
CBL key blinks twice, then release SETUP.
2. Enter 9-7- 3.TheCBL key will blink two times.
3. Press CH- once. The CBL key will blink
four times.
4. Now, the remote control will provide TV and
VCR channel-control capabilities while in the
TV or VCR mode.
To Re-Activate Channel Control Lock:
1. On the remote control, press CBL once.
Then press and hold SETUP until the
CBL key blinks twice, then release SETUP.
2. Enter 9-7- 3.TheCBL key will blink two times.
3. Press CH+ once. The CBL key will blink twice.
4. Now, regardless of what mode you select
(i.e., TV,VCR,orCBL), only the channel
control capability of your cable converter will
be accessible.
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 14

15
USING THE MASTER POWER KEY
The Atlas Universal Remote Control has a unique feature
that allows you to sequentially turn on or off all of your
home entertainment devices with a single key press.
NOTE: MASTER POWER only works in the CBL mode. If it is not
programmed, only the cable converter will turn on or off. In any
other mode, pressing MASTER POWER once will turn on or off the
selected device.
To Program The Master Power Key:
1. On the remote control,press and hold SETUP
until the last-selected device key blinks twice,
then release SETUP.
2. Enter 9- 9- 5. The last-selected device key will
blink twice. Then press POWER once.
3. For the first device you want in the power on
sequence,press a device key (e.g.,CBL) once
and then press POWER once.
4. Repeat step 3 up to three more times to add the
second,third,andfourthdevice,asdesired.
5. To save the settings and exit the program,press
CBL once. Next,press and hold SETUP until the
CBL key blinks twice, then release SETUP.
To Clear The Master Power Key:
1. Perform steps 1 and 2 in the above section.
2. To clear the settings and exit the program,press
and hold SETUP until the CBL key blinks twice,
then release SETUP.
To Operate The Master Power Key:
1. After programming, point the remote control
at the devices.Press CBL once.
2. Press MASTER POWER once to sequentially turn
on or off all home entertainment devices.
3. You will see the devices turn on or off
according to the programmed sequence.
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 15

16
RE-ASSIGNING DEVICE KEYS
The Atlas Universal Remote Control can be set up to
control a second TV or VCR, or any combination of up
to four home entertainment devices. For example, to
have the unit control a TV, a Cable Converter, and two
VCRs, you will need to re-assign the unused AUD key to
operate the second VCR as follows:
1. On the remote control, press VCR once.
Then press and hold SETUP until the
VCR key blinks twice, then release SETUP.
2. Enter 9- 9- 2.TheVCR key will blink twice.
3. Press VCR once, then press AUD once. The
AUD key will blink twice.
4. The AUD key is now ready to be programmed
for your second VCR. See Programming Device
Control on page 8.
To re-assign other device keys,repeat steps 1 to 4 and
substitute the key sequence using the following chart:
To Re-Assign Perform Key Sequence
TV as 2nd VCR key: TV - SETUP - 9- 9- 2- VCR - TV
TV as 2nd Audio key: TV - SETUP - 9- 9- 2- AUD - TV
TV as 2nd Cable key: TV - SETUP - 9- 9- 2- CBL - TV
TV back to TV:TV - SETUP - 9- 9- 2- TV - TV
VCR as 2nd TV key: VCR - SETUP - 9- 9- 2- TV - VCR
VCR as 2nd Audio key: VCR - SETUP -9-9-2-AUD -VCR
VCR as 2nd Cable key: VCR - SETUP -9-9-2-CBL -VCR
VCR back to VCR:VCR - SETUP -9-9-2-VCR - VCR
AUD as 2nd TV key: AUD - SETUP - 9- 9- 2- TV - AUD
AUD as 2nd Cable key: AUD - SETUP -9-9-2-CBL - AUD
AUD back to AUD : AUD - SETUP -9-9-2- AUD - AUD
Upon completion of a re-assignment,the selected mode
key will blink twice to confirm your selection. Then, you’ll
need to program device control (see Programming Device
Control on page 8).
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 16

17
USING MACROS
With programming,the MACRO key on your Atlas Universal
Remote Control can be setup to perform repetitive,time-
consuming operations through the press of a single key.
A macro can be used to control a home theater operation,
to set a favorite channel, or for other multiple functions
you would like to control with one key press (see exam-
ples below). Moreover, the MACRO key can hold up to
three macros with up to 15 key presses each. The macros
are then activated, in the order they were stored, each
time you press this key.
NOTE: If three macros are stored, programming a new macro will
erase the first original macro. Thereafter, each new macro will
overwrite the next original macro.
Example – Programming A Favorite Channel
With so many channels available through your cable
provider, you can program a macro that directly selects a
favorite channel with one key press.For example, let’s
assume your favorite cable programs are on channel 71.
Use the following instructions to program a macro for
direct access of this channel:
1. On the remote control, press CBL once.
Then press and hold SETUP until the
CBL key blinks twice, then release SETUP.
2. Enter 9- 9- 5.TheCBL key will blink twice.
3. Press MACRO once.
4. Press CBL once.
5. Enter the channel number, 7-1.
NOTE: If you have access to over 100 channels, enter
0-7-1. Moreover, if the original remote control
required pressing an Enter key to change the channel,
also press the ENTER key after the channel number
(e.g., 0-7-1-ENTER).
6. Press and hold SETUP until the CBL key blinks
twice, then release SETUP.
Now when you press MACRO, you will instantly see the
cable converter tune to channel 71.
NOTE: To store three channels onto the MACRO key, repeat the six
steps above two more times, substituting a new favorite channel in
step 5 (e.g., 7- 2for channel 72).
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 17

18
USING MACROS (continued)
To Clear A Macro:
1. On the remote control,press and hold SETUP
until the last-selected device key blinks twice,
then release SETUP.
2. Enter 9- 9- 5. The last-selected device key will
blink twice.
3. Press MACRO once.
4. Press and hold SETUP until the last-selected
device key blinks twice, then release SETUP.
NOTE: A macro will be cleared in the order it was
originally stored.
CHANGING VOLUME LOCK
On the Atlas Universal Remote Control,Global Volume Lock
is set to TV,so you can control TV volume while in the TV,
VCR, or Cable mode. If desired, you can still perform
Individual Volume Unlock on a selected device to set its
volume control for independent operation.
NOTE: If you lock the volume controls to the AUDIO mode, you will
still have control of the audio device’s volume in all other modes
(i.e., TV,VCR,andCBL).
To Unlock Volume Control For A Single Device
(Individual Volume Unlock):
1. Assuming Global Volume Lock is active, select a
mode on the remote control that you want to
unlock (e.g.,CBL) and press it once. Next, press
and hold SETUP until the device key blinks
twice, then release SETUP.
2. Enter 9- 9- 3. The last-selected device key will
blink twice.
3. Press VOL– once. The selected device key will
blink four times.
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 18

19
4. Repeat steps 1 through 3 (of this section) for
each device you want volume to be unlocked.
5. Now, after you select a device that has volume
unlocked (e.g., CBL), pressing VOL+,VOL–,or
MUTE, will control the device’s volume only in
its own mode.
To Unlock All Volume Control
(Global Volume Unlock):
NOTE: Performing these instructions will set independent volume
control for all programmed devices (e.g., TV volume control in
TV mode,VCR volume in VCR mode, etc.).
1. On the remote control,press and hold SETUP
until the last-selected device key blinks twice,
then release SETUP.
2. Enter 9- 9- 3. The last-selected device key will
blink twice.
3. Press VOL+ once.The last-selected device key
will blink four times.
To Lock Volume Control To One Mode
(Global Volume Lock):
NOTE: If you lock the volume controls to the AUDIO mode, you will
still have control of the audio device’s volume in all other modes
(i.e., TV,VCR,andCBL).
1. On the remote control,press and hold SETUP
until the last-selected device key blinks twice,
then release SETUP.
2. Enter 9- 9- 3. The last-selected device key will
blink twice.
3. Select a mode (e.g.,TV) where you want to
globally lock the volume controls.The selected
device key will blink twice.
4. Now, when you press VOL+,VOL–,orMUTE,the
volume of the selected device (e.g.,TV) can be
controlled regardless of mode.
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 19

20
TROUBLESHOOTING
PROBLEM: Mode key does not blink when you press a key.
SOLUTION: Replace the batteries with two (2) new AA
alkaline batteries (see page 7).
PROBLEM: Mode key blinks when you press a key, but home
entertainment device does not respond.
SOLUTION: Make sure you are aiming the remote control at
your home entertainment device and that you
are within 15 feet of the device you are trying
to control.
PROBLEM: The remote control does not control home
entertainment devices or commands are not
performing properly.
SOLUTION: Try all listed codes for the device brand being set
up. Make sure all devices can be operated with
an infrared remote control.
PROBLEM: TV/VCR combo does not respond properly.
SOLUTION: Use the VCR codes for your brand.Some combo
units may require both a TV code and aVCR
code for full operation (see page 10).
PROBLEM: No volume on a second TV.
SOLUTION: Follow instructions in Changing Volume Lock
(see page 18).
PROBLEM: CH+ ,CH– ,andLAST do not work for your
RCA TV.
SOLUTION: Due to RCA design (1983-1987),only the original
remote control will operate these functions.
PROBLEM: Changing channels does not work properly.
SOLUTION: If original remote control required pressing
ENTER to change channels,press ENTER on the
remote control after entering a channel number.
PROBLEM: Tried“Search Method”and still could not find a
working code.
SOLUTION: Try the “Search Method” again after clearing out
the device key as follows: Press and hold SETUP
until mode key blinks twice, then release.Next
enter 9- 9- 2.Then press and release the mode
key to be cleared twice.
PROBLEM: Remote control does not turn on Sony or Sharp
TV/VCR Combo.
SOLUTION: For power on, these products require program-
ming TV codes on the remote control.For Sony,
use TV code 0000 and VCR code 0032.For Sharp,
use TV code 0093 and VCR code 0048.
Atlas Manual rev2 E/Sp 5/8/03 5:18 PM Page 20