Universal Forest Products BALAU User manual

6-FT RED BALAU PICNIC TABLE
ASSEMBLY INSTRUCTIONS
Insert four (4) 2-½" carriage bolts into the predrilled seat
crossmember (C) and position so that the bolt heads are on the
ground and the threads are exposed. Be sure to position the
seat crossmember so its outer predrilled holes will be at the top
of the finished assembly. These will be used when assembling
the seat support. Position the legs (E) so that the predrilled
holes align with the bolts and the tops of the legs are level
and straight. Add the washers and secure with the wing nuts.
Repeat step for the second leg assembly (fig. 1).
Place the preassembled table top (A) upside down and position
the legs as shown, making sure the seat crossmember is facing
out. Attach the legs to the table top using four (4) 2-½" carriage
bolts through the predrilled holes and secure with washers and
wing nuts (fig. 2). Repeat step for the second leg assembly.
Once the leg assemblies are attached, tighten carriage bolts
with a wrench.
Step 1
Step 2
Contents
• 1 – Preassembled table top (A)
• 2 – Preassembled seats (B)
• 2 – Predrilled seat crossmembers (C)
• 2 – 24" diagonal braces (D)
• 4 – Predrilled table legs (E)
• 20 – 2-1/2" carriage bolts, washers and wing nuts
• 4 – 1-3/4" wood screws
©2016 Universal Forest Products, Inc. Assembled in the USA with imported fasteners. All rights reserved.
2801 East Beltline NE, Grand Rapids, MI 49525 800.598.9663 8679_2/16
UFPI.com
Items you will need
• Drill or screwdriver with a Phillips head bit
• Adjustable wrench
To maintain the appearance of your table, seal with a finishing oil
every year.
Optional
fig. 2
(4) 2-1/2" carriage
bolts through
crossmember
and legs
Predrilled holes
fig. 1
A
B
C
E
D
(4) 2-1/2"
carriage bolts

THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO REPLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR USE OF
THE PRODUCT MUST BE IN ACCORDANCE WITH ALL LOCAL ZONING AND/OR BUILDING CODES. THE CONSUMER ASSUMES ALL RISKS AND LIABILITY ASSOCIATED WITH THE CONSTRUCTION OR USE
OF THIS PRODUCT. THE CONSUMER OR CONTRACTOR SHOULD TAKE ALL NECESSARY STEPS TO ENSURE THE SAFETY OF EVERYONE INVOLVED IN THE PROJECT, INCLUDING, BUT NOT LIMITED TO,
WEARING THE APPROPRIATE SAFETY EQUIPMENT. EXCEPT AS CONTAINED IN THE WRITTEN LIMITED WARRANTY, THE WARRANTOR DOES NOT PROVIDE ANY OTHER WARRANTY, EITHER EXPRESS
OR IMPLIED, AND SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING CONSEQUENTIAL DAMAGES. FOR DETAILS ON SAFE HANDLING AND WARRANTY INFORMATION, GO TO UFPI.COM / PTINFO.
©2016 Universal Forest Products, Inc. Assembled in the USA with imported fasteners. All rights reserved.
2801 East Beltline NE, Grand Rapids, MI 49525 800.598.9663 8679_2/16
UFPI.com
PICNIC TABLE ASSEMBLY INSTRUCTIONS, CONT.
Position and attach a predrilled diagonal brace (D) between the
seat crossmember and the center table support using the 1-¾"
wood screws. Before attaching the diagonal brace, make sure
the legs are perpendicular to the table top. This will ensure that
the table top is level and the seats can be attached correctly
(fig. 3). Repeat step for the second leg assembly. Turn the table
right side up.
Place the outside edge of the seat support (B) flush with the end
of the seat crossmember. Align the predrilled hole in the seat
crossmember with the predrilled hole in the seat support. Insert
the carriage bolt and secure it using a washer and wing nut (fig. 4).
Repeat step for both ends of each bench.
Ensure all wing nuts and screws are fully tightened.
Step 3
Step 4
Step 5
2-1/2"
carriage bolts
through seat to the
seat crossmember
fig. 4
fig. 3
1-3/4" wood
screws