Universal Furniture 507-634 User manual

INSTRUCTION SHEET
507-634/635
DINING SIDE/ARM CHAIR
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts
that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the assistance of
one or more persons in order to prevent personal injury and to insure parts are not damaged during the assembly
process. If dirty, clean finished parts with mild dishwashing liquid and water solution applied on damp cloth. Cloth
should not be excessively wet. Polish finish with soft cloth and an industry recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain
residue and rough surfaces and also check for staples or nails left after removing the packaging material. The
manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for packaging
carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to the
furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Chair Back
1 pc
B
Seat Frame
1 pc
C
Front Leg
2 pcs
D
Left Arm
1 pc
E
Right Arm
1 pc
1 pc
Assembly Procedure:
Caution: Please do not over-tighten bolts during assembly.
Note: First read the chair leveling instructions. This is an additional assembly instruction sheet found
inside the carton.
Step 1: Place all chair parts on a soft and smooth surface.
Step 2: Take off plastic cover on upholstery seat. Attach Chair Back (A) to back rail of Seat Frame (B)
using ---#3(bolt + spring washer + flat washer), Tighten with wrench (4).
Step3: Attach rear corner blocks of Seat Frame (B) to back post using ---#1(bolt + spring washer + flat
washer), Tighten with wrench (4).
Step4: Attach front corner blocks of Seat Frame (B) to Front Leg (C) using ---#2(bolt + spring washer
+ flat washer). Tighten with wrench (4).
Step5:
（
Only for Arm Chair
）
Attach the Left Arm (D) & Right Arm (E) to Seat Frame (B) using ---
#5(bolt + spring washer + flat washer), Tighten with wrench (4). Attach end of Left Arm (D) &
Right Arm (E) to Chair Back (A) using ---#6(bolt + spring washer + flat washer) by Allen
wrench (7). Then, attach wooden plugs (8) into the end of Left Arm (D) & Right Arm (E).
Step6: After making sure all bolts are attached and hand tightened, turn the chair over.
Step7: Level the chair following “Chair Leveling Instruction”. This is an additional assembly instruction
sheet found inside the carton.
Step 8: Make sure the chair is level and tighten all bolts completely using the wrench supplied.

INSTRUCTION SHEET
507-634/635
DINING SIDE/ARM CHAIR
Hardware List
2
4
3
1
NO
4pcs
1pc
Qty.
6
For Both
Side
Chair&
Arm Chair
4pcs
2pcs
Only
Arm Chair
Bolt+Spring Washer+Flat Washer
--
1/4" Dia
1-3/4" L
5
Wrench
Bolt+Spring Washer+Flat Washer
--
1/4" Dia
3" L
1-1/2" L
2-1/4" L
Bolt+Spring Washer+Flat Washer
-- 1/4" Dia
Bolt+Spring Washer+Flat Washer
--
1/4" Dia
7Allen Wrench
Wooden Plug
1pc
2pcs
2pcs
8
1-1/2" L
Bolt+Spring Washer+Flat Washer
--
1/4" Dia
2pcs
Assembly is now complete.
7