Universal Remote Control Easy Clicker UR3-SR3 User manual

Universal Remote Control, Inc.
www.universalremote.com
UR3-SR3
Operating Manual
For Easy Clicker

1
This remote control is designed to operate
most Digital and Analog Cable Boxes, as well
as TVs, and a DVD player.
Introduction
Install two
AAA alkaline batteries
as shown here
1
Before you program or operate the remote
control, you must install two new AAA alkaline
batteries.
STEP1 Remove the battery compartment cover
from the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
Replacing Batteries
2

2
A. Quick Set-Up Method
A. Quick Set-Up Method
STEP1 Turn on the component you want to
program. To program your TV, turn on the TV.
Button Functions
3
Programming the Remote Control.
4
*Note : In this section, when you are instructed to
press a [DEVICE] button, that means you
should press either the CBL, TV, or DVD
button, depending on which device you are
programming the remote to operate.

STEP2 Press and hold the [DEVICE] key for 5
seconds until the Device LED will blink
once and stays on. Continue to hold the
[DEVICE] key and press the number key
assigned to your brand in the Quick Set-
up Code Table and release both [DEVICE]
key and the number key to save the
code. The Device LED will blink twice to
confirm that the code is stored.
STEP3 Point the remote control at the
component.
STEP4 Press the [DEVICE] button. If it turns off,
it is programmed for your component. If it
does not turn off, use the Pre-
Programmed 3-Digit code Method or
Scanning Method.
Repeat the steps above for all components (CBL,
TV, DVD).
B. Quick Set-up Code Tables
B. Quick Set-up Code Tables
3
Quick Number Manufacturer/Brand
CBL
0 PACE DTA
1 SA/CISCO, SAMSUNG, PACE DIGITAL
2 MOTOROLA DIGITAL
3 MOTOROLA DTA
4 EVOLUTION DTA
5 CISCO IPTV
6 ADB IPTV
7 TECHNICOLOR
8 AMINO 140/540 IPTV
9 MOTOROLA IPTV

4
C. Manual Programming
C. Manual Programming
The remote control can be programmed by entering
a three-digit code number that corresponds to
particular brands and models of equipment. The
three-digit code numbers are listed in the code
tables sections of this instruction manual.
STEP1 Turn on the equipment that you want the
remote control to operate Cable Box, TV
and DVD.
STEP2 Press the [DEVICE] button and the
DVD
0 HITACHI
1 SONY
2 PHILIPS
3 SAMSUNG
4 PHILIPS MAGNAVOX
5 PANASONIC
6LG
7JVC
8 DENON
9 PIONEER
Quick Number Manufacturer/Brand
Quick Number Manufacturer/Brand
TV
0 SANYO
1 SONY
2 SAMSUNG
3LG
4 TOSHIBA
5 PANASONIC
6 PHILIPS
7 HITACHI
8SHARP
9 VIZIO

[OK/SEL] button simultaneously for three
seconds. The corresponding device LED
will turn on indicating that it is ready to be
programmed. The LED will remain on for
20 seconds. The next step must be
entered while the LED is on.
STEP3 Point the remote control toward the
equipment and enter the three-digit code
number assigned to your brand from the
code tables. If there are more than one
three-digit number listed for your brand,
try one code number at a time until your
equipment turns off.
*Note : You can verify that you have selected the
correct code by pressing the [MUTE]
button. The equipment should turn on or
off.
STEP4 Store the three-digit code by pressing the
same [DEVICE] button once again. The
device LED will blink twice to confirm that
the code has been stored.
*Note : Try all the functions on the remote
control. If any of the functions do not
operate as they should, repeat the
instructions from Step 2 using the next
three-digit code number from the same
brand list.
D. Auto Search Method
D. Auto Search Method
If none of the three digit code numbers assigned to
your brand of equipment works, or the code table
does not list your brand, you can use the Auto
Search Method to find the correct three-digit code
number for your equipment by following steps:
5

6
STEP1 Turn on the equipment that you want the
remote control to operate (Cable Box, TV,
or DVD).
STEP2 Press the [DEVICE] button and the
[OK/SEL] button simultaneously for three
seconds. The device LED will turn on
indicating that it is ready to be
programmed. The LED will remain on for
20 seconds. The next step must be
entered while the LED is on.
STEP3
Press the [CH5] or [CH6] button one at a
time or keep it pressed. The remote will
emit a series of Power ON/OFF code
signals. Release the [CH5] or [CH6]
button as soon as the equipment turns off.
*Note : You can verify that you selected the
correct code by pressing the [MUTE]
button. The equipment should turn On or
Off.
STEP4 Press the same [DEVICE] button to store
the code. The Device LED will blink twice
to confirm that the code has been stored.
E.
E. To find the Three-Digit Code that Was To find the Three-Digit Code that Was
Programmed using the Auto Search Method
Programmed using the Auto Search Method
STEP1 Press the appropriate [DEVICE] button
and the [OK/SEL] button simultaneously
for three seconds. The device LED will
turn on for 20 seconds. The next step
must be performed while the LED is on.
STEP2 Press the [INFO] button. The device LED
will blink a number of times indicating the
number of each digit for the code. Each
digit is separated by a one second

interval of the LED being off.
Example : One blink, then three blinks, then eight
blinks indicates the code number 138.
*Note : Ten blinks indicates the number 0.
F.
F.
Programming a Second TV to the DVD Button
Programming a Second TV to the DVD Button
STEP1 Press the [DVD] button and the [OK/SEL]
button simultaneously for 3 seconds. The
DVD LED will turn on for 20 seconds. The
next step must be performed while the
LED is on.
STEP2 Press the [TV] button.
STEP3 Point the remote control toward the TV and
enter the three-digit code for your TV from
the TV codes table.
STEP4 Store the three-digit code by pressing the
[DVD] button. The device LED will blink
twice to confirm that the code has been
stored.
G. Programming for Advanced Functions.
G. Programming for Advanced Functions.
In the CABLE device mode, the A,B,C,D and blank
macro buttons can be programmed to act as a
'Macro' or Favorite Channel button. This allows
you to program up to five 2-digit channels, four 3-
digit channels or three 4-digit channels that can
be accessed with ONE button press.
*Note : The A,B,C and D buttons are not
programmable if you have a Digital
Cable Box made by Pace, Pioneer or
Scientific-Atlanta.
STEP1 Press the [CBL] button to select the CBL
mode.
7

STEP2 Press the [MACRO] button and [OK/SEL]
button simultaneously for 3 seconds. The
[CBL] button will turn on for 20 seconds.
STEP3 Enter the 2, 3 or 4-digit code for the
channel you want programmed first (for
example, 007) using the Number Pad,
then press the [STOP] button. Then enter
the code for the next channel (for
example, 050), then press the [STOP]
button. Repeat this process for the third
channel. The [CBL] button will blink once
for each channel entered.
STEP4 Press the [CH
5 ] button to store the
channels that were selected. The [CBL]
button will blink twice to confirm the
storage of commands.
To access the programmed channels, press
the [MACRO] button once. This will bring up
the first channel. Press once again and it
will bring up the second channel. Press
again and it will bring up the third channel.
To erase the Macro programming and return to
the original function:
STEP1 Press the [CBL] button to select the
CABLE mode.
STEP2 Press a [MACRO] button and the
[OK/SEL] button simultaneously for 3
seconds. The CBL device LED will turn on
for 20 seconds. The next step must be
performed while the LED is on.
STEP3 Press the [CH
5
] button to erase the
functions stored in the button. The CBL
8