Universal Remote Control Easy Clicker UR3-SR3 User manual

Universal Remote Control, Inc.
www.universalremote.com
UR3-SR3
Operating Manual
For Easy Clicker

1
This remote control is designed to operate
most Digital and Analog Cable Boxes, as well
as TVs, and a DVD player.
Introduction
Install two
AAA alkaline batteries
as shown here
1
Before you program or operate the remote
control, you must install two new AAA alkaline
batteries.
STEP1 Remove the battery compartment cover
from the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
Replacing Batteries
2

2
A. Quick Set-Up Method
A. Quick Set-Up Method
STEP1 Turn on the component you want to
program. To program your TV, turn on the TV.
Button Functions
3
Programming the Remote Control.
4
*Note : In this section, when you are instructed to
press a [DEVICE] button, that means you
should press either the CBL, TV, or DVD
button, depending on which device you are
programming the remote to operate.

STEP2 Press and hold the [DEVICE] key for 5
seconds until the Device LED will blink
once and stays on. Continue to hold the
[DEVICE] key and press the number key
assigned to your brand in the Quick Set-
up Code Table and release both [DEVICE]
key and the number key to save the
code. The Device LED will blink twice to
confirm that the code is stored.
STEP3 Point the remote control at the
component.
STEP4 Press the [DEVICE] button. If it turns off,
it is programmed for your component. If it
does not turn off, use the Pre-
Programmed 3-Digit code Method or
Scanning Method.
Repeat the steps above for all components (CBL,
TV, DVD).
B. Quick Set-up Code Tables
B. Quick Set-up Code Tables
3
Quick Number Manufacturer/Brand
CBL
0 PACE DTA
1 SA/CISCO, SAMSUNG, PACE DIGITAL
2 MOTOROLA DIGITAL
3 MOTOROLA DTA
4 EVOLUTION DTA
5 CISCO IPTV
6 ADB IPTV
7 TECHNICOLOR
8 AMINO 140/540 IPTV
9 MOTOROLA IPTV

4
C. Manual Programming
C. Manual Programming
The remote control can be programmed by entering
a three-digit code number that corresponds to
particular brands and models of equipment. The
three-digit code numbers are listed in the code
tables sections of this instruction manual.
STEP1 Turn on the equipment that you want the
remote control to operate Cable Box, TV
and DVD.
STEP2 Press the [DEVICE] button and the
DVD
0 HITACHI
1 SONY
2 PHILIPS
3 SAMSUNG
4 PHILIPS MAGNAVOX
5 PANASONIC
6LG
7JVC
8 DENON
9 PIONEER
Quick Number Manufacturer/Brand
Quick Number Manufacturer/Brand
TV
0 SANYO
1 SONY
2 SAMSUNG
3LG
4 TOSHIBA
5 PANASONIC
6 PHILIPS
7 HITACHI
8SHARP
9 VIZIO

[OK/SEL] button simultaneously for three
seconds. The corresponding device LED
will turn on indicating that it is ready to be
programmed. The LED will remain on for
20 seconds. The next step must be
entered while the LED is on.
STEP3 Point the remote control toward the
equipment and enter the three-digit code
number assigned to your brand from the
code tables. If there are more than one
three-digit number listed for your brand,
try one code number at a time until your
equipment turns off.
*Note : You can verify that you have selected the
correct code by pressing the [MUTE]
button. The equipment should turn on or
off.
STEP4 Store the three-digit code by pressing the
same [DEVICE] button once again. The
device LED will blink twice to confirm that
the code has been stored.
*Note : Try all the functions on the remote
control. If any of the functions do not
operate as they should, repeat the
instructions from Step 2 using the next
three-digit code number from the same
brand list.
D. Auto Search Method
D. Auto Search Method
If none of the three digit code numbers assigned to
your brand of equipment works, or the code table
does not list your brand, you can use the Auto
Search Method to find the correct three-digit code
number for your equipment by following steps:
5

6
STEP1 Turn on the equipment that you want the
remote control to operate (Cable Box, TV,
or DVD).
STEP2 Press the [DEVICE] button and the
[OK/SEL] button simultaneously for three
seconds. The device LED will turn on
indicating that it is ready to be
programmed. The LED will remain on for
20 seconds. The next step must be
entered while the LED is on.
STEP3
Press the [CH5] or [CH6] button one at a
time or keep it pressed. The remote will
emit a series of Power ON/OFF code
signals. Release the [CH5] or [CH6]
button as soon as the equipment turns off.
*Note : You can verify that you selected the
correct code by pressing the [MUTE]
button. The equipment should turn On or
Off.
STEP4 Press the same [DEVICE] button to store
the code. The Device LED will blink twice
to confirm that the code has been stored.
E.
E. To find the Three-Digit Code that Was To find the Three-Digit Code that Was
Programmed using the Auto Search Method
Programmed using the Auto Search Method
STEP1 Press the appropriate [DEVICE] button
and the [OK/SEL] button simultaneously
for three seconds. The device LED will
turn on for 20 seconds. The next step
must be performed while the LED is on.
STEP2 Press the [INFO] button. The device LED
will blink a number of times indicating the
number of each digit for the code. Each
digit is separated by a one second

interval of the LED being off.
Example : One blink, then three blinks, then eight
blinks indicates the code number 138.
*Note : Ten blinks indicates the number 0.
F.
F.
Programming a Second TV to the DVD Button
Programming a Second TV to the DVD Button
STEP1 Press the [DVD] button and the [OK/SEL]
button simultaneously for 3 seconds. The
DVD LED will turn on for 20 seconds. The
next step must be performed while the
LED is on.
STEP2 Press the [TV] button.
STEP3 Point the remote control toward the TV and
enter the three-digit code for your TV from
the TV codes table.
STEP4 Store the three-digit code by pressing the
[DVD] button. The device LED will blink
twice to confirm that the code has been
stored.
G. Programming for Advanced Functions.
G. Programming for Advanced Functions.
In the CABLE device mode, the A,B,C,D and blank
macro buttons can be programmed to act as a
'Macro' or Favorite Channel button. This allows
you to program up to five 2-digit channels, four 3-
digit channels or three 4-digit channels that can
be accessed with ONE button press.
*Note : The A,B,C and D buttons are not
programmable if you have a Digital
Cable Box made by Pace, Pioneer or
Scientific-Atlanta.
STEP1 Press the [CBL] button to select the CBL
mode.
7

STEP2 Press the [MACRO] button and [OK/SEL]
button simultaneously for 3 seconds. The
[CBL] button will turn on for 20 seconds.
STEP3 Enter the 2, 3 or 4-digit code for the
channel you want programmed first (for
example, 007) using the Number Pad,
then press the [STOP] button. Then enter
the code for the next channel (for
example, 050), then press the [STOP]
button. Repeat this process for the third
channel. The [CBL] button will blink once
for each channel entered.
STEP4 Press the [CH
5 ] button to store the
channels that were selected. The [CBL]
button will blink twice to confirm the
storage of commands.
To access the programmed channels, press
the [MACRO] button once. This will bring up
the first channel. Press once again and it
will bring up the second channel. Press
again and it will bring up the third channel.
To erase the Macro programming and return to
the original function:
STEP1 Press the [CBL] button to select the
CABLE mode.
STEP2 Press a [MACRO] button and the
[OK/SEL] button simultaneously for 3
seconds. The CBL device LED will turn on
for 20 seconds. The next step must be
performed while the LED is on.
STEP3 Press the [CH
5
] button to erase the
functions stored in the button. The CBL
8

9
device LED will blink twice to confirm that
the memory button has been erased.
H.
H. Assigning the Volume and Mute keys Assigning the Volume and Mute keys
to a Different Device
to a Different Device
By default, the VOL 5 , VOL 6 and MUTE keys
operate through your TV. If you would like those
keys to operate those functions on a different
device, follow these steps.
STEP1 Press the [OK/SEL] button and [CBL]
button simultaneously for three seconds.
The device LED will turn on for 20
seconds. The next step must be
performed while the LED is on.
STEP2 Press the [VOL
5
] button. The device
LED will blink.
STEP3 Press the [DEVICE] button corresponding
to the device that you would like the
volume and mute buttons to control. The
device LED will blink twice to confirm the
programming.
Example : If you wish to have the volume and
mute keys operate your Cable Box,
press the [CBL] button in Step3.
I.
I. Assigning the Channel keys to a Assigning the Channel keys to a
Different Device
Different Device
By default, the CH
5
, CH
6
, NUMERIC and LAST keys
operate through your Cable Box. If you would like
those keys to operate those functions on a different
device, follow these steps.
STEP1 Press the [OK/SEL] button and [CBL]
button simultaneously for three seconds.
The device LED will turn on for 20

10
seconds. The next step must be
performed while the LED is on.
STEP2 Press the [VOL
6 ] button. The device LED
will blink.
STEP3 Press the [TV] button. The device LED
will blink twice to confirm the
programming.
*Note : If you wish to have the channel keys
operate your Cable Box, press the [CBL]
button instead of the [TV] button in Step 3.
J.
J.
Assigning the DV
Assigning the DVD D– –VOD keys to VOD keys to
control your DVD
control your DVD
By default, the REW, Play, FF, Record, Stop and
Pause keys operate VOD (Video On Demand)
through your Cable Box. If you would like those
keys to operate those functions on your DVD,
press the PLAY button for 3 seconds until the DVD
button lights. To return to your Cable Box control,
press the PLAY key again for 3 seconds until the
CBL button lights.
K.
K. Low Battery Warning Low Battery Warning
When the battery is low (2.3V-2.0V) and needs to be
replaced with fresh batteries, device LED will blink 2
times in sequence whenever a [DEVICE] button is
pressed to turn on equipment.
L.
L. Memory Lock System. Memory Lock System.
This remote control is designed to retain
programmed memory for 10 years — even after
batteries are removed from the remote control.
For additional information about your remote
control, go to www.universalremote.com

1 1
Set-up Code Tables
5
MAKER(BRAND) NAME
CODE No
CONVERTER
CABLE TV
CISCO/SA EXPLORER Series 001 007
8600X 011
8600 021
8540,8570,8590 022
8500 023
IPN Series 051
LogicTV 209
MOTOROLA DCT Series (DVR Model) 002
VIP Series 053
DTA100 206
GENERAL INSTRUMENT DCT Series,DCH Series, CFT2200 008
DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027
JERROLD BMC9012/BMC9022 006
DSR470 005
CFT2000 012
DRZ 024
DL4,DP(V),DQN(V),DPBB 025
DRX 002
Some Model 048
DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027
ADB ADB Series 054 055
ADB5810WX 115
ADB5810W 163
AMINO AmiNET Series 249
A125, A130, A530 256 257
A110 260 261
ARRIS MP2000 172
Frontier 216
AT&T U-VERSE 051
BELL FIBE PVR Slim 205
CINCINNATI BELL ZTE 194
CISCO RNG200 113
IPN Series 051
CIS330, CIS430 156
DIGITAL TRANSPORT ADAPTER50 001
COMCAST RNG200 113
XFINITY 195
CONFLUENT CTG4-HDR 196
DIGEO 2056-MSX 153
DirecTV Genie 238
Sky AP HD / Sky Ap Jr 239
DREAM DM7020S 159
DSTV DSTV [PVR1] 182
DSTV [PVR2] 183
DUNE SMART B1,BE,D1,H1,HE,ME 184
MINI,ULTRA 185

12
MAKER(BRAND) NAME
CODE No
CONVERTER
CABLE TV
ENTONE URC PLUS 155
Kamai 500 210
213
EVOLUTION FTA X0-01 158
EVOLUTION UNIVERSAL SD DTA 189
UNIVERSAL HD DTA 215
HAMLIN CR6000 042
CR6600,6800,CR83 043
CRX5000 044
HOMECAST NC3000C01 176
KAON Mini 208
MOXI MOXI MEDIA CENTER 006
MOXI HD DVR 052
2056-MSX 153
MYRIO Evo Series 054 055
NAGRA DCI-4136M 211
NAGRAVISION HDDTA 201
NBOX ADB-5720SX 181
ABD5720SX 186
NFUSION NUVENIO SD PHOENIX, NUVENIO HD,
SOLARIS, NOVA 192
NOW TV NOWTV 114
NSC IM781R 046
IM781 047
OAK SIGMAONE, P1,P2,P3, SIGMA 2000 037
RTC56,RKDM 038
SIGMA 2001,2002 039
SIGMA 450,500,550 040
PACE 500 Series 001 007
TDC Series 002
DTA Series 113
510 004
DC550DR 214
DC60X 206
IPH8005M 217
PANASONIC 140,145,170,175 030
110,120,130,150,160 031
PIONEER VOYAGER Series 001 007
BA9000 013
BA4100,4200,4500 028
BA-V1000 029
REGENCY ALL MODELS 045
SAMSUNG OCAP MODELS 001 007
130
SEACHANGE ANALOG CONVERTER 190
HD TCM 191
SKY SKY+HD 230
SKY HD 204

13
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
CABLE-DVR(TIVO)
CHANNEL MASTER 859
DSTV 836 837 838 839 840
HUGHES 817 821 822 823 824 825 826 827 828
HUMAX 817 818
ICREALTIME 834 816
PHILIPS 790 817 821 822 823 824 825 826 827 828 835
TIVO 790 817 818 821 822 823 824 825 826 827 828 858
TOSHIBA 817
ZUUMMEDIA 855
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
TV
ADMIRAL 072 081 160 161 096
AD NOTAM 672
ADVENT 147
AFFINITY 680
AIWA 141 145
AKAI 070 146 004 148 124 226 104 108 244
AKIO 103
ALARON 028
AMARK 112 127
AMERICA ACTION 043
AMPRO 073 167
ANAM 043 054 056 080 112 131
AOC 058 070 004 112 245
APEX 092
APEX DIGITAL 015 150 037 724
AQUAVISION 097 100 686
AUDIOVOX 076 103 043 035 078 224
AUVIO 689
AVIELO 090 628
AVION 223
SONY DHG-M55CV 003
TECHNICOLOR 365
TELNET RC-RW100 154
THOMPSON DCI1011GEM,DCI1011GEM1,DCI104ICS 365 188
TILEVISION TV19 187
TOCOM 5507 035
5503A 036
TRANSPARENT VIDEO SYSTEMS 4000A 193
WEGENER SMD 515 050
WINDSTREAM KINETIC 212
ZENITH MN2500 032
PM 033
Z-TAC 034
MAKER(BRAND) NAME
CODE No
CONVERTER
CABLE TV

14
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
TV
AXESS 711
BAYSONIC 043
BELL&HOWELL 072
BENQ 234
BRADFORD 043
BROKSONIC 096 170
CAIRN 162
CANDLE 070 002 003 004
CAPEHART 058
CARVER 164
CELEBRITY 001
CETRONIC 043
CIELO 714
Ciil 732
CINERAL 103 120
CITIZEN 070 002 003 004 101 103 127
CLASSIC 043
COBY 640 641 671 236
CONCERTO 004
CONTEC 043 051
CORONADO 127
CRAIG 043 054 028
CROSLEY 164
CROWN 043 127
CURTIS MATHES 070 004 101 011 072 081 120 164 127
CXC 043
DAEWOO 076 103 112 004 127 016 043 044 125 120
DAYTRON 004 127
DELL 041 249
DENON 011
DIGITAL PROJECTION 090
DUMONT 004 073
DWIN 131 132 161
DYNASTY 043
DYNATECH 062
FISHER 007 057
ELECTROBAND 001
ELECTROHOME 024 076 127
ELEMENT 004 110 622 690
EMERSON 005 028 043 048 076 096 155 004 051 151 153
154 127 121
ENVISION 070
EPSON 087 228
ESA 031
FREEMOTION 688
FUJITSU 164 197 028 157 149 066 217
FUNAI 028 043 052 168
FUSION 642

15
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
TV
FUTURETECH 043
GATEWAY 165 031
GE 070 073 130 144 160 161 004 008 009 034 056
074 091 155 081 120
GEM 031
GIBRALTER 004 073
GOLDSTAR 004 106 112 127
GPX 674
GRUNPY 028 043
HAIER 004 116 623 236
HALL MARK 004
HANNSPREE 099
HARLEY DAVIDSON 028
HARMAN KARDON 164
HARVARD 043
HISENSE 198 021 619 630 631 236
HITACHI 011 007 009 004 072 010 012 023 075 158 127
174 243 670
HP 027 039 098
HUMAX 122
HYPERION 242
HYUNDAI 049 067
ILO 055 096
INFINITY 164
INFOCUS 046 215 225 233 726
INKEL 129
INSIGNIA 068 069 078 096 164 168 247
INTEQ 073
JBL 164
JCB 001
JCPENNEY 004 008 024 030 065 070 101 160 156 127
JENSEN 013
JVC 038 001 034 083 195 159 227 639
KENWOOD 070 001
KLEGG 220
KLOSS 002 059
KREISEN 202
KTV 070 043 154 127
LG 004 106 112 127 086 236 648
LODGENET 072
LOEWE 196 164
LOGIK 072
LUXMAN 004
LXI 007 015 052 081 160 164
MAGNAVOX 070 003 004 022 059 060 061 063 064 127 164
094 160 056 028 035 211 205 218 050 138 232
MAJESTIC 072
MARANTZ 164 070 143 169

16
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
TV
MATSUI 164
MATSUSHITA 080
MAXENT 165
MEGATRON 004
MEMOREX 004 007 072 028 096
METZ 088
MGA 024 070 004 042
MIDLAND 073
MINERVA 088
MINTEK 077
MINUTZ 008
MITSUBISHI 109 024 042 004 040 146 028 124 081 200 235
MOTOROLA 081
MTC 070 004 062 101
MULTITECH 043
NAD 015 025
NEC 070 130 134 040 056 007 019 024 004 182 140 717
NEXUS 620 078
NIKEI 043
NIKKO 103
NIKO 175
NORCENT 211
NTC 103
NUVISION 084
OLEVIA 219 004 161 144 160
ONKING 043
ONWA 043
OPTIMUS 080
OPTOMA 029 032
OPTONICA 019 081
ORION 096 201 203 204 205 028
PANASONIC 080 034 056 164 190 230 248 237 240 664
PEERLESS-AV 723
PHILCO 070 003 004 024 056 059 060 063 064 127 164
PHILIPS 164 005 038 093 127 070 003 004 059 199 218
161 232 629 727
PIONEER 023 025 135 176 004 018 070 183 191 208 214 182 660
PLANAR 728
POLAROID 026 118 119 006 110
PORTLAND 004 103 127
PRISM 034
PROSCAN 144 160 161 167 236
PROTON 004 058 171 173 193 127 163
PROTRON 102 213 004 115
PROVIEW 110
PROX 092
PYLE HOME 661 662
QUASAR 034 056 239

17
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
TV
RADIO SHACK 004 019 127 043
RCA 160 161 144 156 065 070 004 023 024 056 074
152 081 209 713
REALISTIC 007 019
REVOLUTION HD 220
RUNCO 072 073 130 179 180 181 182 216 194 697
SAMPO 070 004 058 165
SAMSUNG 192 089 004 101 127 133 160 105 070 184 185 515 655
SANSEI 120
SANSUI 096 244 078
SANYO 007 053 057 082 020
SCEPTRE 036 699
SCOTCH 004
SCOTT 004 005 028 043 048 127 113
SEARS 004 007 015 028 030 057 082 094 160 052 164 127
SEIKI 690
SELECO 189
SEMIVOX 043
SEMP 015
SEURA 704
SHARP 081 019 014 028 004 022 127 684 692
SHERWOOD 128
SIGNATURE 072
SOLE 177 178
SONY 001 241 633 126 139
SOUNDESIGN 003 004 028 043
SOYO 163
SPECTRICON 112
SPECTRONIQ 004
SQUAREVIEW 052
SSS 004 043
STARLITE 043
SUNBRITE 633 634 635 236
SUNBRITE TV 238
SUPRE MACY 002
SUPREME 001
SVA 046
SYLVANIA 070 003 059 060 063 064 127 160 164 044 056
168 121 231
SYMPHONIC 052 168
SYNTAX OLEVIA 219 004 161 144 160
TANDY 081
TATUNG 056 062
TCL 705
TECHNICS 034 080
TECHNOL ACE 028
TECHVIEW 246
TECHWOOD 004

18
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
DVD
ADCOM 203
AIWA 210 214
AKAI 239
ALPINE 179
ANTHEM 361
APEX DIGITAL 240 197 247 248 196
ARCAM 165 148 374
AUDIOVOX 075
BOSE 244 245
CAMBRIDGE AUDIO 224 145 360
CARY AUDIO DESIGN 249 149
CLASSE 242
COBY 206
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
TV
TEKNIKA 002 003 004 024 028 043 072 101 103 164 127
TELEFUNKEN 244
TELERENT 072
TERA 172
THOMPSON 166
TILEVISION 663
TMK 004
TNCI 073
TOSHIBA 015 030 007 040 062 101 142 045 137 703
TOTEVISION 127
TRUTECH 212
UNIVERSAL 008 009
UPSTAR 708
VENTURER 236
VIDEO CONCEPTS 146
VIDIKRON 188 164 182
VIDTECH 004
VIEWSONIC 210 211 720
VIORE 055 229
VISCO 110
VIZIO 236 031 624 004 625 675
WARDS 004 064 164 008 009 019 028 060 061 063 072
074 070 127
W Box Technologies 731
WESTINGHOUSE 076 036 221 222 001 280 690 695
WINBOOK 079
YAMAHA 004 070 206 207
YORK 004
YUPITERU 043
ZENITH 011 072 073 095 103 096
ZONDA 112