Universal Remote Control Star Light SL-7000 User manual

OPERATING MANUAL
Universal
Remote
Control
Model: SL-7000

Thank you for purchasing the Star Light universal remote control.
This unit was desingned to fully complement your home entertainment
system. Any comments or questions about this product should be
directed to Universal Remote Control, Inc., New Rochelle, NY 10801.
You can also call our toll-free Customer Service Line at
1-800-901-0800 for any assistance.
Please read this instruction manual carefully.
The Star Light universal remote control has many advanced features
that can add enjoyment and convenience during its use. Keep these
instructions for future reference.
2

Table of Contents
Introduction ...............................................................
4
Battery Installation ...................................................
5
Programming the Remote
.........................................
6 7
A. Quick Set-Up
C. Standard Set-Up
Advanced Features
......................................................
8 12
A. Code Number Recall
B. Storing Multi-Commands/Favorite Channels to emory Buttons
C. Assigning Device Codes to other Device Buttons
D. Punch-Through TV Volume Control
E. Punch-Through VCR Control
Satellite key pad Information
.........................................
13
Hidden Buttons
..........................................................
13
Glossary .................................................................... 13
Warranty and Specifications
...........................................
14
Three Digit Code Lists .................................................. 15 30
A. TV Codes
B. VCR Codes
C. CATV Codes
D. SAT Codes
E. Audio Codes
F. Aux Codes
Satellite Functions by code
............................................. 31~44
Page
3

INTRODUCTION
The Star Light universal remote control can replace or consolidate up to six (6)
of your remote controls. It is already preprogrammed, so there is no need to
have your original remote. The Star Light universal remote works with virtually
all IR (Infrared) equipment, including : TV' s, VCR's, Cable Boxes, Satellite
Receivers, Compact Disc Players, A/V Receivers, Cassette Decks, and many other
audio /video components.
4

Battery Installation
The Star Light remote control is powered by four AAA batteries(included). Please
be sure to match the (+) and (-) on the batteries to the (+) and (-) marking inside
the battery compartment.
Battery Compartment Cover Removal
To remove the battery compartment, located on the rear of the remote, press down
and push forward toward the top of the remote control.
To close the battery compartment cover, slide the cover straight back until it clicks
into place.
Diagram for opening and closing of the battery cover is shown below.
Note :
When changing batteries, please replace the new batteries within ten minuites.
Otherwise, resetting of your codes may be required.
5

Programming the Remote
A. Quick Set-Up:
Step 1: Turn on the device (TV, VCR,CABLE BOX, SATELLITE RECEIVER,etc .)
you wish to operate.
Step 2: On the remote control, press the corresponding DEVICE button
(TV, VCR, CATV , SAT, etc.) and MUTE button simultaneously.
Note: SET will appear in the LCD.
Step 3: Point the remote control toward the device. Punch in the first three digit
code number assigned to your brand from the brand code lists located on
pp.(15 30).The device will turn off when the correct code has been selected.
Step 4: Once the device turns off, press the corresponding DEVICE button again
to store the code.
Note: LCD will flash PASS indicating that the code has been
stored.
Step 5: Test the remote control functions with the code that was just stored.
If any of the buttons do not perform as they should, please repeat from
Step 2 using the next three digit code number for your brand of equipment.
6

Programming the Remote,( Continued )
7
C. Standard Set-Up:
Step 1: Turn on the device ( TV, VCR, Cable Box, Satellite Receiver, etc. ) that you
wish to operate.
Step 2: On the Star Light universal remote control, press the corresponding
DEVICE button (TV, VCR,CATV, SAT,Audio,or Aux) and the MUTE
button simultaneously.
Note: SET will appear in the LCD.
Step 3: Locate the three digit code number for your brand of equipment from the
code lists found on pp. (15 31). Example: TV codes-Sony 001,003,etc.
Note: If the brand list contains more than one code number,
select the first code listed.
Step 4: Point the remote control at the devise turned on in Step1and press in the
three digit code number selected in Step 3.
Note: SET # # # will appear in the LCD.
Your device will turn off when the correct code has been selected. If the
device fails to turn off, go back to Step 3 and select the next three digit
code for your equipment, and press in the code number.
Note: Repeat the above step until the device turns off. When
the device turns off proceed to Step 5.
Step 5: Press the DEVICE button (TV, VCR, CATV, SAT, Audio, Aux) on the
remote control to store the three digit code that turned off your equipment.
Note: PASS will flash in the LCD indicating that the code has
been stored.
Step 6: Test the remote control functions with the code just stored.
Example: Power, Channel Up, Volume Up, etc. If any of the buttons do not
perform as they should, please repeat from Step 2using the next three digit
code until the right code is found.
Step 7: To program other devices into the corresponding Device button of the
remote control, repeat the above steps with the respective devices and Device buttons.

Advanced Features
A. Three Digit Code Number Recall:
If you wish to find a code number that has been stored in your remote control,
please use the following steps:
Step 1:
On the remote control, press the DEVICE and MUTE buttons simultaneously.
Note: SET will appear in the LCD.
Step 2: Press the INPUT button. The LCD will flash the three digit code number
for five seconds before returning to its original sate.
B. Storing Multi-Commands/Favorite Channels to Memory Buttons
Memory buttons M1, M2, M3and M4can be set up to store up to six(6) commands
with one button push. Any functions, in any Device mode (except Channel up and
Channel down), can be stored in any one of the four memory buttons.
This will enable you, for example, to turn on the TV and Satellite receiver and select
a preassinged satellite channel with only one button push.
Method of setting up:
Step 1: Press the Device button (TV, VCR, CATV, SAT, AUX, AUDIO) and MUTE
button, simultaneously.
Note: SET will appear in the LCD.
Step 2:
Press one of the memory buttons(M1-M4) that you would like to designate
for multi-command or favorite channel operation.
Note: M (1-4)will appear in the LCD. The memory button
is now ready to be set up.
Step 3: Press up to six commands that you would like to store in the memory button.
Note: Each successive selection will appear as 1~6 in the LCD.
Step 4: Press the Channel(+) button to store your selection.
Note: SAVE will flash twice and the Device mode will appear in the LCD.
Please repeat the above steps for the remaining memory buttons.
8

Example:
Memory button M1in the SAT mode can be set up to do the following functions: to turn on
the Satellite receiver, select channel #18 on the satellite receiver, and then turn on the TV.
Step 1:Press the SAT and MUTE buttons, simultaneously.
Note: SET will appear in the LCD.
Step 2
: Press memory button M1.
Note: M 1will appear in the LCD.
Step 3
: Press the Power buttons (to turn on the satellite receiver).
Note: M 1 1 will appear in the LCD.
Press the # 1button (to select the first digit of channel # 18)
Note: M 1 2 will appear in the LCD.
Press the # 8 button (to select the second digit of channel # 18)
Note: M 1 3 will appear in the LCD.
Press the TV Device button (to select the TV Device mode).
Note: M 1 4 will appear in the LCD.
Press the Power button (to turn on the TV).
Note: M 1 5 will appear in the LCD.
Step 4
: Press the Channel (+)button to store the above commands.
Note: SAVE will flash and the current Device mode will appear.
Now, anytime the memory button M1is pressed while the remote control is in the
SAT mode, the commands to turn on the Satellite receiver, select the Satellite channel
#18 and turn on the TV, will be sent out by the remote control.
Memory buttons can be used in any combination you select.
Note: Any previously stored multi-commands on a memory button will be erased
when new multi-commands are stored to that same memory button.
9

C. Assigning Different Device Codes to other Device Buttons
This feature can be used to program the remote control for more than one TV, VCR,
Satellite Receiver, etc. The three digit code for any device can be stored in any of the
DEVICE buttons. For example: For two VCRs, the first VCR can be stored in the VCR
DEVICE button under normal set up procedures, and the second VCR can be
programmed into the unused CATV or any other DEVICE button.
Step 1: Turn on the device you wish to operate.
Step 2: On the remote control, press the DEVICE button you wish to assign this
device to, and the MUTE button simultaneously.
Note: SET will appear in the LCD.
Step 3: Press the DEVICE BUTTON that corresponds to the actual device you plan
to operate.
Note: SET will appear in the LCD.
Step 4: Select the three digit code number from the code list found on pp.
(15 30) for the device you will be operating
Step 5: Point the remote toward the device, and press in the three digit code
number.
Note: SET # # # will appear in the LCD.
Step 6: The device will turn off when the correct three digit code number has been
selected. Press the DEVICE button selected in Step 2. This will store the three
digit code into that DEVICE button.
Note: PASS will flash in the LCD.
Advanced Features (Continued )
10