Universal Tool UT8002 Specifications

Manufacturer/Supplier Product Type RPM
Cycles Per Min
Model No/Nos Serial No
Product Nett Weight
lbs
Kg
Recommended Use Of
Balancer Or Support
Recommended Hose Bore
Size - Minimum
Recommended Max.
Hose Length
Ins M/M Ft M
No
Page No 1
3/8 and 1/2 Square Drive
Ratchet Wrenches
UT8002 - 3/8 SQ
UT8012 - 1/2 SQ
2.64
1.20 3/8 10 30 10
170
Includes - Foreseen Use, Work Stations, Putting Into Service,
Operating, Dismantling, Assembly and Safety Rules
Operator Instructions Important
Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
Universal Air Tool Company Limited
Unit 8
Lane End Industrial Park
High Wycombe
Bucks
HP14 3BY
Work Stations
The tool should only be used as a handheld hand operated tool.
It is always recommended that the
tool is used when standing on the
solid floor. It can be used in other
positions but before any such use, the
operator must be in a secure position
having a firm grip and footing and be
aware that when loosening fasteners
the tool can move quite quickly away
from the fastener being undone. An
allowance must always be made for
this rearward movement so as to
avoid the possibility of hand/arm/
body entrapment.
Foreseen Use Of The Tool
The tool is designed to be used only for the purpose of driving,
tightening and loosening of threaded fasteners, usually nuts and
bolts, when fitted with a suitable drive socket.
It is allowed to use suitable extension bars, universal joints and
socket adaptors between the square output drive of the ratchet
wrench and the female square drive of the socket.
Do not use the tool for any other purpose than that specified
without consulting the manufacturer or the manufacturer's
authorised supplier. To do so may be dangerous.
Never use the ratchet wrench as a hammer to dislodge or
straighten cross threaded fasteners. Never attempt to modify
the tool for other uses and never modify the tool even to be
used as a ratchet wrench.
Putting Into Service
Air Supply
Use a clean lubricated air supply that will give a measured air
pressure at the tool of 90 p.s.i./6.3 bar when the tool is running
with the trigger fully depressed. Use recommended hose size
and length. It is recommended that the tool is connected to the
air supply as shown in figure 1. Do not connect the tool to the
air line system without incorporating an easy to reach and
operate air shut off valve. The air supply should be lubricated. It
is strongly recommended that an air filter, regulator, lubricator
(FRL) is used as shown in Figure 1 as this will supply clean,
lubricated air at the correct pressure to the tool. Details of such
equipment can be obtained from your supplier. If such
equipment is not used then the tool should be lubricated by
shutting off the air supply to the tool, depressurising the line by
pressing the trigger on the tool. Disconnect the air line and pour
into the intake bushing a teaspoonful (5ml) of a suitable
T
el No Fax No(01494) 883300 (01494) 883237
Noise Level S/Pressure 84.0 (8002) 86.0 (8012) dB(A)
T
est Method Tested in accordance with Pneurop
test code PN8NTC1 and ISO Standard 3744
S/Power 95.0 (8002) 96.0 (8012) dB(A)
V
ibration Level
T
est Method Tested in accordance with ISO
standards 8662 Parts 1 & 7
2.9 (8002) 2.6 (8012) Metres / Sec²
Personal Safety Equipment
Use - Safety Glasses Yes
Use - Safety Gloves
Use - Safety Boots
Use - Breathing Masks
Use - Ear Protectors
Air Pressure
Recommended Working
6.3 bar 90 PSI
Recommended Minimum n/a bar n/a PSI
Maximum
7.0 bar 100 PSI

Page No 2
Safety Rules For A Ratchet Wrench
1) Read all the instructions before using this tool. All operators
must be fully trained in its use and aware of these safety rules.
2) Do not exceed the maximum working air pressure.
3) Use personal safety equipment.
4) Use only compressed air at the recommended conditions.
5) If the tool appears to malfunction remove from use
immediately and arrange for service and repair.
6) If the tool is used with a balancer or other support device
ensure that it is fixed securely.
7) Always keep hands away from the working attachment fitted
to the tool.
8) The tool is not electrically insulated. Never use the tool if there
is any chance of it coming into contact with live electricity.
9) Always when using the tool adopt a firm footing and/or
position and grip the tool firmly to be able to counteract any
forces or reaction forces that may be generated whilst using the
tool.
10) Use only correct spare parts. Do not improvise or make
temporary repairs.
11) Do not lock, tape, wire, etc. the on/off valve in the run
position. The trigger/lever etc. must always be free to return to
the 'off' position when it is released.
12) Always shut off the air supply to the tool, and depress the
trigger/lever etc. to exhaust air from the feed hose before fitting,
adjusting or removing the working attachment.
13) Check hose and fittings regularly for wear. Replace if
necessary. Do not carry the tool by its hose and ensure the hand
is remote from the on/off control when carrying the tool with
the air supply connected.
14) Take care against entanglement of moving parts of the tool
with clothing, ties, hair, cleaning rags, etc. This will cause the
body to be drawn towards the tool and can be very dangerous.
15) It is expected that users will adopt safe working practices
and observe all relevant legal requirements when installing,
using or maintaining the tool.
16) Do not install the tool unless an easily accessible and easily
operable on/off valve is incorporated in the air supply.
17) Take care that the tool exhaust air does not cause a problem
or blows on another person.
18) Never lay a tool down unless the working attachment has
stopped moving.
19) Always ensure that the reverse button is in the selected
position before starting the tool.
20) Do not use sockets with excessive wear to the input and
output drives. Periodically check the square drive on the ratchet
wrench. Make sure the socket, extension is firmly fixed to the
tool.
21) When loosening fasteners first ensure that there is sufficient
clearance behind the tool to avoid hand entrapment. The tool
will move away from the threaded joint as the nut/bolt is
loosened and rides up the thread moving the tool with it.
pneumatic motor lubricating oil preferably incorporating a rust
inhibitor. Reconnect tool to air supply and run tool slowly for a
few seconds to allow air to circulate the oil. If tool is used
frequently lubricate on daily basis and if tool starts to slow or
lose power.
It is recommended that the air pressure at the tool whilst the
tool is running is 90 p.s.i./6.3 bar. The tool can run at lower and
higher pressures with the maximum permitted working air
pressure of 100 p.s.i./7.0 bar.
Operating
Fit securely to the tool the socket or attachment required to
perform the operation. Ensure that the reverse button situated
on the opposite side to the square drive output shaft is in the
correct position for tightening or loosening the fastener.
The nut/bolt can then be run down the thread using the power
drive of the tool. When the tool stops the handle of the tool can
be used as a ratchet lever and operated to give the required
tightness of the joint.
For loosening a joint the tool can be used in the reverse
sequence.
Dismantling & Assembly Instructions
Disconnect tool from air supply.
Grip motor housing with bushing (1) in a vise fitted with soft
jaws. With a snap ring plier, remove the retaining ring (52). By
using a adjustable wrench, unscrew the air hose assembly (53),
inlet bushing (50) and inlet bushing (12) then separate o-ring
(14), connecting ring (51), muffler (13) and o-ring (14). Unscrew
valve screw (11) and remove o-ring (10), (9), air regulator (8),
spring (7), throttle pin (6), o-ring (5), (4). Use a proper steel bar,
tap out pin (3) and remove throttle lever (2) from motor housing
with bushing (1). Release housing with bushing (1) from vise,
slide off comfort grip (48) from housing with bushing (1) then
return housing with bushing to vise.
Remove retainer ring (46) and by moving ratchet yoke (34) from
side to side to push out the complete ratchet anvil assembly out
of the ratchet housing (30). Remove the thrust washer (45),
steel balls (44) and springs (43). Rotate reverse button (35) until
a semi-circular groove in it lines up with pin (40). Then, tap out
pin (40) by using a suitable punch, remove ratchet pawl (42) ,
lock pin (37), spring (36) and reverse button (35) from ratchet
anvil (41). Do not try to remove the steel ball from the drive of
ratchet anvil (41) and only remove roll pin (39) from ratchet anvil
(41) when a replacement is required. Remove ratchet yoke (34),
washer (38), drive bushing (33) and crank shaft (32) from
ratchet housing (30). Unscrew lock ring (28) from internal gear
(25) then unscrew ratchet housing (30) (left hand thread) from
lock ring (28). With a suitable punch, tap needle bearing (31),
bushing (29) out of ratchet housing (30) slightly. Remove planet
gear carrier (27) and planet gears (26) from internal gear (25).
Do not remove any of the pins from planet gear carrier (27). Use
a special wrench which locates in the teeth of the internal gear
(25), unscrew the internal gear (25) from motor housing with
bushing (1). If this proves to be difficult to unscrew, provide
some local heating to the lock ring (28) and/or internal gear (25)
to soften and break the grip of the thread locking sealant. Pull
out the motor assembly from housing with bushing (1). Grip the
front end plate (22), to avoid the splines of rotor (20) from
damage, use a rubber hammer , slightly tap the splined end of
the rotor (20) through the front end plate (22) and ball bearing
(23) assembly. Take off cylinder (19) and remove rotor blades
(21). With a suitable punch, tap the rear end of rotor (20) slightly
to separate rotor (20) from rear end plate (17). Then, press out
ball bearing (23) from front end plate (22) and ball bearing (16)
from rear end plate (17). Do not remove the steel balls (18) from
front end plate (22) and rear end plate (17) unless replacements
are required.
Reassembly
Clean all parts and examine for wear. Look in particular for wear
and cracks on ratchet pawl (42), ratchet anvil (41) and ratchet
yoke (34). Coat all parts with a pneumatic tool lubricating oil and
grease all bearings, gears, and ratchet mechanism parts with a
molybdenum or lithium based general purpose grease. Before
reassembling the motor, make sure that the faces of rear end
plate (17) and front end plate (22) that abuts cylinder (19) are flat
and free from burrs. If necessary, lap on a flat, very fine grade of
abrasive paper. Reassemble in the reverse order. When refitting
the complete motor assembly to the housing with bushing (1),
make sure that the assembly is clamped tightly together and the
rotor spins freely, ensure the steel ball (18) in the side of front
end plate (22) locates in the slot in motor housing with bushing
(1).

UT8002
UT8012
3/8 SQ Drive Ratchet Wrench
1/2 SQ Drive Ratchet Wrench
Page No 3
Oct 2003 Ver 1.0
Ref No Part No Description
1 RL60201P Motor Housing
w/ Bushing
2 RL80512C1 Throttle Lever
3 RL805132 Pin
4 RL80504 O-Ring
5 RL80505 O-Ring
6 RL80506 Throttle Pin
7 RL80507 Spring
8 RL13004 Air Regulator
9 RL80509 O-Ring
10 RL80510 O-Ring
11 RL80511 Valve Plug
12 RL602121B Air Inlet
13 RL80416 Muffler
14 RL80515 O-Ring (2)
16 RL80417 Ball Bearing
17 RL80418 Rear End Plate
18 RL80421 Steel Ball (3)
19 RL80422 Cylinder
20 RL60220 Rotor
21 RL80420 Rotor Blade (4)
22 RL60222 Front End Plate
23 RL80524 Ball Bearing
25 RL60225 Internal Gear
26 RL60226 Planet Gear (3)
27 RL60227 Planet Gear Carrier
28 RL60228 Lock Ring
29 RL60229 Bushing
Ref No Part No Description
30 RL602301 Ratchet Housing
31 RL60231 Needle Bearing
32 RL60232 Crank Shaft
33 RL60233 Drive Bushing
34 RL60234 Ratchet Yoke
35 RL60235 Reverse Button
36 RL60236 Spring
37 RL60237 Lock Pin
38 RL60238 Washer
39 RL60239 Roll Pin
40 RL60240 Pin
41
RL60241 Ratchet Anvil
(3/8" Drive)
RL60341 Ratchet Anvil
(1/2" Drive)
42 RL60242 Ratchet Pawl
43 RL60243 Spring (2)
44 RL60244 Steel Ball (2)
45
RL60245 Thrust Washer
(3/8" Drive)
RL60345 Thrust Washer
(1/2" Drive)
46 RL60246 Retaining Ring
48 RL60248V Comfort Grip
50 RL804141BS Air Inlet
51 RL60251 Connecting Ring
52 RLCR101 Retaining Ring
53 RL602531 Air Hose Assembly
XL60203 Nameplate

Distributor
Notes
Page No 4
A
ccessories
Declaration of Conformity
Universal Air Tool Company Limited
Unit 8, Lane End Industrial Park, High Wycombe, Bucks, HP14 3BY, England
declare under our sole responsibility that the product
Models UT8002/UT8012 Ratchet Wrenches, Serial Number
to which this declaration relates is in conformity with the following standard(s) or other normative document(s)
EN792 (Draft), EN292 Parts 1 & 2, ISO 8662 Parts 1 & 7, Pneurop PN8NTC1
following the provisions of 89/392/EEC as amended by 91/368/EEC & 93/44/EEC Directives
Place and date of issue Name and signature or equivalent marking of authorised person
Lane End D.H.Moppett (Man. Director)
This document may not be copied wholly or in part by anyone without the consent of the Directors of Universal Air Tool Company Limited
©Copyright of Universal Air Tool Company Limited, established in the United Kingdom, 1994
Designed & Written in the U.K.