Universal Tool UT8942 User manual

UT8942
RIVNUT SETTING TOOL
PLEASE READ AND FOLLOW ALL WARNINGS
Read Operating Instructions
Always become familiar with all the
instructions and warnings before
operating any power tool.
Always Wear Approved
Eye Protection
Impact resistant eye protection
should meet or exceed the
standards as set forth in the United
States ANSI Z87.1, Occupational
and Educational Eye and Face
Protection. Look for the marking
Z87.1 on your eye protection to
insure that it is an approved style.
For further information, ANSI Z87.1,
Occupational and Educational Eye
and Face Protection, is available
from the American National
Standards Institute, Inc., 11 West
42nd Street, New York, NY 10036.
Hearing Protection is
Recommended
Hearing protection should be used
when the noise level exposure
equals or exceeds an 8 hour time-
weighted average sound level of 85
dBA. Process noise, reflective
surfaces, other tools being
operated nearby, all add to the
noise level present in your work
area. If you are unable to determine
your noise level exposure, we
recommend the use of hearing
protection.
Avoid Prolonged Exposure to
Vibration
Tools can vibrate during use.
Prolonged exposure to vibration or
very repetitive hand and arm
movements, can cause injury.
Stop using any tool if discomfort,
tingling feeling or pain occurs. You
should consult your physician
before resuming use of the tool.
90 PSIG Maximum
This tool is designed to operate at
an air pressure of 90 pounds per
square inch gauge pressure (90
PSIG) maximum, at the tool. Use of
higher air pressure can, and may
cause injury. Also, the use of
higher air pressure places the
internal components under loads
and stresses they were not
designed for, causing premature
failure. The air supply should be
clean and dry, preferably
lubricated. For best results, drain
the moisture from your compressor
daily.
Universal Tool
A Division of Florida Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter, Florida 33458
Toll Free 1-800-327-9403
Read these instructions carefully before attempting to install, operate
or service this Florida Pneumatic product. Failure to comply with the
instructions could result in personal injury and/or property damage!
Retain these instructions for future reference.
Safety Instructions
The following instructions are furnished
as general guidelines for use of your
pneumatic tool. They cannot compre-
hensively cover all possible or conceiv-
able uses of the subject tool. For
additional information on the safe use
of air tools, we advise you to obtain a
copy of ANSI B186.1 Safety Code for
Portable Air Tools, available from the
following source:
American National Standards
Institute, Inc.
11 West 42nd Street
New York, NY 10036.
The use of the word “shall” in the
following instructions, indicates that
adherence to the particular require-
ment is necessary to conform to ANSI
B186.1.
Tool Application and Usage
Portable tools shall be used only for
the purposes intended in their design
and within the capacity for which they
were intended and rated. It shall be
the tool owner’s and/or employer’s
responsibility to instruct each operator
in the safe use of the tool. Tools shall
not be used without guards and safety
devices as furnished by the manufac-
turer. Where an air tool is modified or
altered, the modifier shall provide the
safeguards to enable it to be safely used
in the operations intended and to comply
with any applicable provisions as
contained in ANSI B186.1.
Tool Installation
Pressure regulators shall be used to limit
air pressure to the rated pressure where
the supply pressure exceeds the tool’s
rated pressure. Air hoses and lines shall
be relieved of compressed air before
being disconnected or disjointed, unless
there is automatic valve closing protec-
tion at the joint being separated. Syn-
thetic lubricants which can cause
deterioration of elastomer seals shall not
be used in air systems of air tools.
Tool Maintenance
It shall be the tool owner’s and/or
employer’s responsibility to assure that
tools are maintained in a safe operating
condition. Tool maintenance and repair
shall be performed by authorized,
trained, competent personnel. Tools shall
be disconnected from their compressed
air supply before repairs are attempted.
Repairs shall be consistent with the
manufacturer’s recommended proce-
dures. Tool, hoses and fittings shall be
replaced if unsuitable for safe operation.
It shall be the tool owner’s and/or
employer’s responsibility to keep required
rating markings and warnings on the tool
in legible condition.
FPMC
WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals
known to cause cancer, birth defects or
reproductive harm. Some examples of
these chemicals are:
•Lead from lead-based paints
•Crystalline silica from bricks, cement
and other masonry products
•Arsenic and chromium from chemi-
cally treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals, work in a well-ventilated
area and work with approved safety
equipment such as those dust masks that
are specially designed to filter out
microscopic particles.
Description
Universal Tool Air Riveter Nut Tool is designed to set ribbed rivet nuts, hex body
rivet nuts, and threaded inserts in S.A.E. and metric sizes.

UT8942 UT8942
LOOTGNITTESTUNVIRLOOTGNITTESTUNVIR
Limited Warranty
Universal Tool warrants its tools to be free from defects in material and workmanship for one year from the date of
purchase. This warranty does not apply to tools which have been abused, misused, modified or repaired by
someone other than Universal Tool or its authorized service centers. If a Universal Tool proves defective in
material of workmanship within one year after purchase, return it to any authorized service center or to Universal
Tool, freight prepaid. Please enclose your name, address and adequate proof of purchase date with a brief
description of the defect. Universal Tool will, at its option, repair or replace defective tools, free of charge. Repairs
or replacements are warranted as described above for the remainder of the warranty period. Universal Tool's sole
liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective tool.
There are no other warranties expressed or implied and Universal Tool shall not be liable for incidental, consequential
or special damages, or any other damages, costs or expense of repair or replacement as described above.
Index Part Description NO. Index Part Description NO.
NO. NO.
Req'd
NO. NO.
Req'd
1 9350010 Motor Housing 1 39 9M04007 Bolt M4 1
9M05008 Bolt M5 1
2 9P2514 Spring Pin 1 9M06010 Bolt M6 1
3 925004 Ball Bearing 1 9W08032 Bolt 8-32 1
4 925003 Rear Plate 1 9W10024 Bolt 10-24 1
5 935009 Cylinder 1 9W10032 Bolt 10-32 1
6 925007 Rotor Blade 5 9W14020 Bolt 1/4"-20 1
7 935002A Rotor 1 40 960094 Bushing #4 1
8 925008 Front Plate 1 960095 Bushing #5 1
9 925023 Ball Bearing 1 960096 Bushing #6 1
10 935018B Planet Gear 3 960094 Bushing 6-32 , 8-32 1
11 910445 O-Ring 2 960095 Bushing 10-24, 10-32 1
12 923211 Motor Gasket 1 96009614 Bushing 1/4"-20 1
14 960011A Planet Cage (15T) + Pin 1 41 960063 Washer #3-#6 1
15 925018B Roll Pin 1 960063 Washer 6-32,8-32, 10-24,10-32,1/4"-2
0
1
16 935016 O-Ring 2 42 935012A Internal Gear 1
17 935007 Valve Stem 2 43 935065 Needle Bearing #3-#8 1
18 935006 Sleeve 2 935065 NeedleBearing6-32,8-32,10-24,10-32,1/4"-20,
5/16"-18
1
19 935039 O-Ring 2 48 960004M Nut Anvil #4 1
20 935003 O-Ring 2 960005M Nut Anvil #5 1
21 935005 Throttle Bushing 2 960006M Nut Anvil #6 1
22 935004 Screw 1 960004M Nut Anvil 8-32 1
23 935002 Trigger 1 960005M Nut Anvil 10-24, 10-32 1
24 990016A Bushing 1 96001-4-20 Nut Anvil 1/4"-20 1
25 935015A Housing 1 49 935049 Muffler 1
26 935060 Ball Bearing 1 50 935062 Diffuser Exhaust 1
27 935059 Planet Pin 2 51 935061 Air Inlet Bushing 1
28 990014B Planet Gear (18T) 2 52 935029 Pin 1
31 990010W Planet Cage 1 53 982162 Rubber Sleeve 1
33 935069 Ball Bearing 1 ***ACCESSORIES ***
34 935014F Screw Housing 1 *9350W34 Wrench 34mm 1
37 935076 Spring 1 *9350W38 Wrench 38mm 1
38 9600004 Hexagon Bit #4 1
9600005 Hexagon Bit #5 1 * Not Show n
9600006 Hexagon Bit #6 1
9600832 Hexagon Bit 8-32 1
9601024 Hexagon Bit 10-24 1
9601032 Hexagon Bit 10-32 1
9601420 Hexagon Bit 1/4"-20 1