Universe Future ZWG2000AG User manual

Universe Future Technology Co.,LTD
Introduction of Gateway
Introduction
of
Gateway
ZWG2000AG

Universe Future Technology Co.,LTD
2
Introduction of Gateway
Catalogue
Catalogue........................................................................................................................................... 2
1 Description................................................................................................................................... 3
2 Diagram........................................................................................................................................... 4
3 Specification............................................................................................................................... 5
4 LED Status..................................................................................................................................... 6
5 Installation................................................................................................................................. 7
6 Operation....................................................................................................................................... 7
6.1 Power on/off.....................................................................................................................7
6.2 Web Setting....................................................................................................................... 7
6.3 Base Information.............................................................................................................8
6.4 Network Information.......................................................................................................8
6.5 Network Settings.............................................................................................................9
6.6 Z-Wave Reset...................................................................................................................10
6.7 Password Modify.............................................................................................................10
6.8 Z-Wave device information.........................................................................................11
6.9 Inclusion.........................................................................................................................11
6.10 Exclusion.......................................................................................................................12
6.11 Remove fail device.....................................................................................................13
6.12 Replace fail device...................................................................................................14
6.13 Rebuilt Router.............................................................................................................15
6.14 Learn Mode.....................................................................................................................15
6.15 Shift............................................................................................................................... 16
6.16 Refresh Frequency Settings.................................................................................... 17
6.17 System Time Settings.................................................................................................17
6.18 Log File.........................................................................................................................18
6.19 IP Reset.........................................................................................................................18
6.20 Password Reset.............................................................................................................19
7 Router Settings.........................................................................................................................19
8 APP................................................................................................................................................. 20
9 Quick Manual............................................................................................................................... 20
10 Glossary..................................................................................................................................... 22
Release Record............................................................................................................................... 22

Universe Future Technology Co.,LTD
3
Introduction of Gateway
1 Description
Thanks for Purchasing Universe Future Technology Co,.LTD products.
Gateway(ZWG2000AG) which based on z-wave technology is professionally designed
for Internet of Things.It work like a bridge between the internet and the appliance
or the office device,user can remotely control the Light,Curtain Motor,Air
Condition,TV,Projector and so on,via the APP which designed and worked with
gateway,it also can deal with the data which received from sensor ,to support the
smart control.Meanwhile our gateway integrated security system,user can remotely
monitor online via the IP camera,when alarm happen,our system can send message to
user in the first time.Our gateway adopt z-wave technology which is bidirectional
communication,that make it possible to know the status of device anytime,wireless
communication is convenience for constructing,no need wiring.Humanized logic and
User Interface designed make user feel very comfortable when using our products.
Products that are Z-Wave certified can be used and communicate with other Z-Wave
certified devices.
Feature：
• ARM9-S™ ARM® Thumb® Processor running at up to 400 MHz,high quality assurance.
• Modular Design for Hardware,easy for future update and modify.
• Simple Linux kernel for Software system,easy for maintain and APP
Update.
• Support multiple communication protocol：Z-wave,TCP/IP,UPNP,DDNS,
HTTP,DNS.
• Redundant design for the communication between the gateway and control
terminal,make the alarm message send in time.
• Support web for configuration,convenience for setting and modify.
• Internal log file design,safer for fault analyses.
• Separating Reset mode design，user can chose to reset only password or
HomeID or Gateway IP.
• Support Encipher Transmit Mode and non-Encipher Transmit Mode.
• Support TSL between the gateway and terminal.

Universe Future Technology Co.,LTD
4
Introduction of Gateway
2 Diagram
Figure 2-1: Gateway
Figure: 2-2 Front
Figure:2-3 Right
Figure: 2-4 Back
1
2
3
4
5
6
7
8
10
9
11
15
13
14
12

Universe Future Technology Co.,LTD
5
Introduction of Gateway
Table 2-1
No. Name Function
1 Power Button and Power LED Power on/off、Power status
2 Download LED Data download status
3 Inclusion/Exclusion LED Inclusion/Exclusion status
4 Z-Wave LED Radio status
5 WAN LED WAN Link status
6 LAN LED LAN Link status
7 Z-Wave Logo Z-Wave Logo
8 Product Name Product Name
9 Inclusion/Exclusion Button Inclusion/Exclusion operation button
10 Power Plug Power plug
11 Reset Button Reset IP and password
12 USB Manual update new version
13 Mini USB ISP
14 Ethernet Port Network interface
15 Antenna Antenna for wireless
3 Specification
Table 3-1
Items Specification
CPU ARM9 (400 M[email protected] Inclusion/Exclusion 10%)+ ZM3102
DRAM 128M
Flash 256M
Voltage 5DCV
Current 0.5A
Consumption <2.5w
Frequency
Range ≤30m(inside)，100m（outside）
Node 232
Protocol TCP/IP、UPNP、DDNS、HTTP、DNS、Z-Wave
Temperature 10-45℃
Humidity 10%-70%RH
Power Adapter（5V 1.5A）
Weight 350g
Dimension 165mm*165mm*30mm
908.4MHz

Universe Future Technology Co.,LTD
6
Introduction of Gateway
4 LED Status
Table4-1
LED Status Description
Power Supply LED: On/Blue Power on right now
Ethernet Port LED: On/Orange Ethernet port power on
Ethernet Port LED: On/Green Ethernet port physics link is ok
Ethernet Port LED:Blink/Green Gateway is communicating right now
Down load LED:Blink/Green Gateway is updating new version
Inclusion/Exclusion LED:
Blink/Blue
Gateway is on Exclusion mode
Inclusion/Exclusion LED:Blink/Green Gateway is on Inclusion mode
Inclusion/Exclusion LED:Blink/Blue
and Green
Gateway is rebuilding z-wave router
Inclusion/Exclusion LED:On/Green→Off
IP reset（when holding for 3s）
Inclusion/Exclusion LED:On/Blue→Off Password reset（when holding for 10s）
Download and Inclusion/Exclusion
LED:Blink/green
Gateway is starting
z-wave LED:Blink/Green Gateway is communication with other device
WAN LED:On/Green Gateway link with Internet OK
WAN LED:Blink/Green Gateway is checking the internet status
WAN LED:Off Gateway do not link to Internet
LAN LED:On/Green Physical Link between Gateway and router is ok
LAN LED:Blink/Green Gateway is communicating right now(tcp/ip)
LAN LED:Off Physical Link between Gateway and router is not ok

Universe Future Technology Co.,LTD
7
Introduction of Gateway
5 Installation
The product does not require installation.After breaking package,assembling
antenna,putting gateway on a desk which is 0.8m - 1.0m high,then power on, connecting
to router with network table.
NOTE：
* DO NOT PUT GATEWAY ON THE GROUND OR LOWER PLACE.
* DO NOT USE AC POWER ADAPTER WHICH DO NOT CONFORM TO THE REQUIREMENTS OF PRODUCTS
SPECIFICATION.
* GATEWAY IS A STATIC CONTROLLER WHICH IS NOT PORTABLE,PLEASE DO NOT MOVE IT
AFTER RE-BUILTING ROUTER.
* IT IS BETTER AWAY FROM OTHER RADIO SOURCE.
* RF JIMMING IS NOT PERMIT WHEN USING GATEWAY.
6 Operation
6.1 Power on/off
Power on
Function：power supply,start system
Step：
Step-1：Plug in AC adapter
Step-2：Press power button
（Power LED will turn on with BLUE.After 10s,the Download LED and
Inclusion/Exclusion LED will blink for 13s,then Download LED and
Inclusion/Exclusion LED will turn off,then system is ready）
Power off
Function：power off and shutdown the system
Step：
Step-1：Press power button
（Button will pop-up,then the Power LED will turn on）
6.2 Web Setting
Web Setting
Function：view system setting
Step：
Step-1：Running Browse
Step-2：Input Gateway IP at address field,format is“IP:8080”，for example
“192.168.0.88:8080”,“192.168.0.98”is gateway IP，“8080”is port number.

Universe Future Technology Co.,LTD
8
Introduction of Gateway
（Gateway default IP：192.168.0.88，port：8080，password：888888）
Step-3：Enter （Then screen turn to login page，figure 6.2-1）
Step-4：Input gateway ID in “控制器 ID”field,Input gateway in“密码”field.
Step-5：Click“登陆”
（If ID and password are right ,will turn to web manage page,figure 6.2-2）
Figure 6.2-1 Figure 6.2-2
6.3 Base Information
Base Information
Function：view base information，contain gateway ID、product ID、version
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“基本信息” （figure 6.3-1）
Step-3：Click“控制器基本信息” （figure 6.3-2）
Figure 6.3-1 Figure 6.3-2
6.4 Network Information
Network Information
Function：view network information,contain gateway IP、sub mask、router IP、Time
server IP
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Cilck“基本信息” （figure 6.4-1）

Universe Future Technology Co.,LTD
9
Introduction of Gateway
Step-3：Click“网络信息” （figure 6.4-2）
Figure 6.4-1 Figure 图 6.4-2
6.5 Network Settings
Network Settings
Function：network settings
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“控制器管理” （figure 6.5-1）
Step-3：Click“网络配置” （figure 6.5-2）
Step-4：Input gateway IP、sub mask、router IP and time server IP according to user’
s network environment.(server IP MUST be 202.120.2.101)
Step-5：Click“确认”
Step-6：Power off
Step-6：Power on (切记网关要重启之后新的配置才会生效)
NOTE：
* advice user to remember the network setting information after modifying
* the new setting will be valid ONLY after restarting gateway
Figure 6.5-1 Figure 6.5-2

Universe Future Technology Co.,LTD
10
Introduction of Gateway
6.6 Z-Wave Reset
Z-Wave Reset
Function ： initialize z-wave environment,clear z-wave node information ，
re-generate HomeID
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“控制器管理” （figure 6.6-1）
Step-3：Click“控制器复位” （figure 6.6-2）
Step-4：Input password in“登陆密码”field
Step-5：Click“确定”
（after about 60s，gateway will reboot automatically）
Figure 6.6-1 Figure 6.6-2
6.7 Password Modify
Password Modify
Function：modify gateway password
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“控制器管理” （figure 6.7-1）
Step-3：Click“修改密码” （figure 6.7-2）
Step-4：input old in“当前密码”field，input new password in“新密码”，input new
password in“确认新密码”field again
Step-5：Click“确定”
(new password will be valid at once,no need to reboot)
NOTE：
* advice user to remember the new password
* for the security,the password should not be too simple

Universe Future Technology Co.,LTD
11
Introduction of Gateway
Figure 6.7-1 Figure 6.7-2
6.8 Z-Wave device information
Z-Wave device information
Function：view Z-Wave device information，contain device ID、device name、device
type、device supporting command、manufacture ID
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“设备管理” （figure 6.8-1）
Figure 6.8-1
6.9 Inclusion
Inclusion
Function：add new device to z-wave network
Method 1
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)

Universe Future Technology Co.,LTD
12
Introduction of Gateway
Step-2：Click“设备管理” （figure 6.9-1）
Step-3：Click“添加设备”
（then Inclusion/Exclusion LED turn green and blink until success or timeout for
fail）
Step-4：Trigger device to send NIF
（the way to send NIF is different because the device design is different.If
gateway received NIF,the Inclusion/Exclusion LED will turn off）
Figure 6.9-1
Method 2
Step：
Step-1：double click slowly Inclusion/Exclusion button
（then Inclusion/Exclusion LED will turn green and blink until success or timeout
for fail）
Step-2：Trigger device to send NIF
（the way to send NIF is different because the device design is different.If
gateway received NIF,the Inclusion/Exclusion LED will turn off）
NOTE：
* SHOULD do Exclusion first before Inclusion,in order to clear the old data in
device
* the distance of two device should be less then 2m when doing Inclusion
* some device can be operated immediately,for example switch,some device need to
do configuration before it can work normally,for example sensor,please refer
to the introduction of device
6.10 Exclusion
Exclusion
Function：delete a device from network,or clear the old data in the device which
have been inclusion into other network
Method 1
Step：

Universe Future Technology Co.,LTD
13
Introduction of Gateway
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“设备管理” （figure 6.10-1）
Step-3：Click“删除设备”
（then Inclusion/Exclusion LED will turn blue and blink until success or timeout
for fail）
Step-4：Trigger new device to send NIF
（the way to send NIF is different because the device design is different.If
gateway received NIF,the Inclusion/Exclusion LED will turn off ）
Figure 6.10-1
Method 2
Step：
Step-1：Press Inclusion/Exclusion button about 5s until Inclusion/Exclusion LED
blink then release
（then Inclusion/Exclusion LED will turn blue and blink until success or timeout
for fail）
Step-2：Trigger new device to send NIF
（the way to send NIF is different because the device design is different.）
NOTE：
* the distance of two device should be less than 2m when doing Exclusion
6.11 Remove fail device
Remove fail device
Function：delete a fail device which is out of control
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“设备管理” （figure 6.11-1）
Step-4：Chose the device to be removed
Step-5：Click“移除失效设备”
NOTE：
* this operation will success ONLY when the fail device can not send ACK to gateway

Universe Future Technology Co.,LTD
14
Introduction of Gateway
Figure 6.11-1
6.12 Replace fail device
Replace fail device
Function：replace the fail device with a new device
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“设备管理” （figure 6.12-1）
Step-4：Chose the device to be replace
Step-5：Click“移除失效设备”
Step-6：Trigger new device to send NIF
（the way to send NIF is different because the device design is different.）
NOTE：
* this operation will success ONLY when the fail device can not send ACK to gateway
* SHOULD do Exclusion first before doing replace fail device,in order to clear
the old data in device
Figure 6.12-1

Universe Future Technology Co.,LTD
15
Introduction of Gateway
6.13 Rebuilt Router
Rebuilt Router
Function：rebuilt router for the gateway
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“ZWAVE 管理” （figure 6.13-1）
Step-3：Click“确定”of“重建路由”
（then Inclusion/Exclusion LED will blink between green and blue until finish）
NOTE：
* this process will take more time if there are more devices in the network,please
wait and do not login gateway,do not power off all device
* SHOULD do this operation after inclusion all devices and have chosen a static
place for gateway
* rebuilt router Only valid for LISTEN device
Figure 6.13-1
6.14 Learn Mode
Learn Mode
Function：make gateway be Inclusion to another network or Exclusion from anothe
network
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：do Z-Wave reset in “控制器管理” （see 6.6 z-wave rest,ignore this step
if there is no device in gateway）
Step-3：Click“ZWAVE 管理” （figure 6.14-1）
Step-4：Click “确定”of Learn Mode
Step-5：Another primary controller do Inclusion

Universe Future Technology Co.,LTD
16
Introduction of Gateway
NOTE：
* SHOULD do exclusion first before doing this operating
* the distance of two device should be less than 2m when doing Learn Mode
Figure 6.14-1
6.15 Shift
Shift
Function：transfer the Inclusion/Exclusion function to secondary controller
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“ZWAVE 管理” （figure 6.15-1）
Step-4：Click“确定”of “控制权交换”
Step-5：Another second controller set Learn Mode
NOTE：
* the distance of two device should be less than 2m when doing shift
Figure 6.15-1

Universe Future Technology Co.,LTD
17
Introduction of Gateway
6.16 Refresh Frequency Settings
Refresh Frequency Settings
Function：set refresh interval
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“ZWAVE 管理” （figure 6.16-1）
Step-4：Input the time in“自动刷新频率”field
Step-5：Click“确定”of“自动刷新频率”
NOTE：
* value range ：0~60, 0 mean do not refresh，default value is 60
* SHOULD set refresh frequency when using first gateway
Figure 6.16-1
6.17 System Time Settings
System Time Settings
Function：set system clock
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“ZWAVE 管理” （figure 6.17-1）
Step-4：Input the time value in“设置时间”field
Step-5：Click“确定”of “设置时间”
NOTE：
* time formate：year-month-day hour:minute:second, for example“2013-11-29
15:56:18”.There is a space between day and hour
* SHOULD set refresh frequency when using first gateway

Universe Future Technology Co.,LTD
18
Introduction of Gateway
Figure 6.17-1
6.18 Log File
Log File
Function：view log of gateway
Step：
Step-1：Login Web manage page(refer to 6.2 web setting)
Step-2：Click“系统日志” （figure 6.18-1）
Figure 6.18-1
6.19 IP Reset
IP Reset
Function：reset gateway IP
Step：
Step-1：Press Reset button for 3s，when Inclusion/Exclusion LED turn green then
release

Universe Future Technology Co.,LTD
19
Introduction of Gateway
（then Inclusion/Exclusion LED turn green，after system reset ok,gateway will
reboot automatically,default IP will be valid）
NOTE：
* default IP：192.168.0.88
Sub mask：255.255.255.0
Router IP：192.168.0.1
* SHOULD set available IP for gateway after reset
6.20 Password Reset
Password Reset
Function：reset password to factory default
Step：
Step-1：Press Reset button for 10s，then release when Inclusion/Exclusion LED turn
blue
（after reset ok,gateway will reboot automatically,default password will be valid）
NOTE：
* default password：888888
* for security,user should chang password immediately
7 Router Settings
This chapter describe how to set the router in order support remotely control.
Because there are so many kinds of router,herein only show a general way, please
refer to your router introduction for more detail.
Step：
Step-1：login router
Step-2：click port mapping
Step-3：add new item,content as bellow:
Name：Gateway（or user defined）
Internal Port：6000
External Port：6000（or user defined）
IP Address：gateway IP
Step-4：Enable UPnP
Step-5：Enable DNS
Server Supplier：（User select refer to router）
Host Name：（User apply the third server supplier）
User Name：（Supplied by the third server supplier）
Password：（Supplied by the third server supplier）
If User want to use DDNS which supplied by UF,please ignore the step-5.UF supply
DDNS for each product

Universe Future Technology Co.,LTD
20
Introduction of Gateway
8 APP
The software of gateway is different for different using.Please refer to your
introduction of software when you download.
9 Quick Manual
Figure7.1
Figure7.1 is a application of gateway .Number is gateway,number 2、3、4、5、6、
7、8、9、10 are devices(we assume that they are switch module).
Environment：
There is WiFi router,its IP is 192.168.0.1,which have been set for internet,any
device can link to internet when insert network cable.
Gateway default IP:192.168.0.88,default password：888888
9.1 Installation
→Installing device2、3、4、5、6、7、8、9、10 on the wall，power on them
9.2 power on gateway
→Remove packages,insert AC adapt then power on,system will be ready after 60s
9.3 Modify gateway IP
→Connecting gateway to PC with network cable,PC local IP should
be:192.168.0.100，default gateway IP:192.168.0.1
→Running IE browse,input 192.168.0.88:8080,then Enter