UPC 1454A User manual

ASSEMBLY INSTRUCTIONS
PARTS BAG UPC 1454A Icon 48 Pocket Spinner
PARTS LIST
Page 1 of 7
PART Quantity Reference
Push Pin 9(1 extra) A
Long Trusshead Screw 4 B
Connector Bolt 4 C
Short Trusshead Screw 4D
Hex Wrench 1E
Header Clip 1F
PART Quantity Reference
Top Cap 1G
Tower Panel 2H
Spinner Plate 1I
Base 1J
X-Base Lower 1K
X-Base Upper 1L
Racks 48 M
Tower Helper 3N
N
BC
D
Revised 01/12/15
E
TOOLS REQUIRED: #2 Phillips Screwdriver
F
A
U.S. PATENT NO.
8,534,472
G
H
I
J
L
M
K
Finished Display

ASSEMBLY
Insert X-Base Upper (L)
into X-Base Lower (K)
as shown below.
1
Attach Base (J) to
X-Base Assembly (K/L)
using (4) Connector Bolts (C).
2
C
J
L
K
Page 2 of 7
U.S. PATENT NO.
8,534,472

Use Larger
Holes for
attachment
to X-Base.
ASSEMBLY
Page 3 of 7
Spin & align the large
holes in Spinner Plate
and Spinner.
3
4
Align large screw holes on
Spinner Plate Assembly (I) with
one of the four corresponding
holes on the X-Base Assembly.
Spinner Plate
Assembly (I)
(shown
exploded
for reference)
Spinner
Plate
Spinner Plate
Assembly (I).
X-Base
Assembly
Hole 1
Hole 2
Hole 3
Hole 4
Bottom View of Spinner Plate Base (I).
I
I
Hole 2
Hole 3
Hole 1
Hole 1
Hole 2
Hole 3
U.S. PATENT NO.
8,534,472

(finger hole)
(finger hole)
A
Small Hole
(align behind
Large Hole)
Facet with
Large Hole
(align in front
of Small Hole)
ASSEMBLY
A
9
H
Tower Panels (H)
MUST be aligned properly
at facets BEFORE securing
with Push Pins (A).
NOTE:
Push Pins CANNOT be
removed once
inserted into holes!
A. Peel protective masking off
Tower Panels (H) before assembly.
B. Overlap each Tower Panel (H) so the large hole
of facet lies outside the small hole of
opposite panel. (see figure RIGHT)
C. Use Large Finger Holes (see figure RIGHT)
to hold together Tower Panels (H)
tightly while installing Push Pins (A).
D. Join (2) Tower Panels (H) together
using (8) Push Pins (A). (see figure BELOW)
H
(finger
hole)
Page 5 of 7
(finger hole)
close up view
U.S. PATENT NO.
8,534,472
Top of
Tower Panel
(No Slot)
Bottom of
Tower Panel
(With Slot)

Page 6 of 7
H
HOLES
at
and tighten
This step will support Tower Panel
Assembly (H) up for installation to Base
Assembly. Insert (2) Tower Helpers (N)
in-between Spinner Plate Assembly (I) and
Base (J), as shown below.
I J
Base
Assembly
Base
Assembly

Page 7 of 7
ASSEMBLY
G
H
H
Attach Racks (M) by hooking the
tabs into the vertical slots in the
Tower Panels (H).
Lock bottom tongue of Racks (M)
into the horizontal slots on
the Tower Panels (H).
Each vertical slot holds two
Racks (M) side-by-side.
16
Peel masking off Header
Clip (F) and secure to the center
of the Top Cap (
G). Lower
Top Cap (G) on to the top
of the Tower Panel Assembly (H).
15
14
Remove Tower
Helpers (N).
N
U.S. PATENT NO.
8,534,472
F
H
M