Uplift Desk UDA118 User manual

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
®
Front Clamp Standing Converter Instructions
UDA118
UDA118/R01
Package contents
Main unit
(qty 1)
(g. 1)
Clamp
(qty 1)
Keyboard Tray
(qty 1)
M6x25 bolts
(qty 4)
Allen wrench Tacky friction pads
(optional)
DO NOT activate this lever until step 3. Activating the lever
before this step will release the gas-powered cylinder and
cause the unit to rise quickly.
Step 1
Place the Main unit top-down on a at and stable surface.
Using two people, one person hold the Clamp in place as the
other threads the M6x25 bolts into the Clamp onto the Main unit.
Tighten with the Allen wrench.
Again, don’t squeeze the paddle on the Main unit. It will release
the gas-cylinder and cause it to rise quickly, possibly causing injury.
Step 2
With a friend’s help, ip the assembly over and slide it over the
edge of your desk, so that the Clamp is around the edge of your
desk, with the Main unit on top of your desk. (see gure 1)
The Clamp’s plate can be adjusted up and down to accommodate
desks from .78’’ to 2.9’’ in thickness. Move it up for thinner desktops,
and down for thicker desktops.
Once on the desk, screw the Clamp stoppers tight to secure the unit
to your desk.
Step 3
Keep objects clear of the standing converter for this step.
To raise the converter, squeeze the paddle. It is advised you hold
onto it with two hands as you raise (and lower) the worksurface.
This will allow you to adjust the converter and move it to your
desired positions. Release the paddle to lock into place.
Step 4
Undo the latches on both sides of the Main unit.
When in the unlatched position, slide the Keyboard tray onto the
Main unit.
Flip the latches back up. This will secure and lock the tray onto the unit.
CAUTION
!

Step 5
Once the converter is fully assembled, you can start adding your
devices and accessories to the upper worksurface.
Use the optional Tacky friction pads to increase friction of the
devices on the worksurface. Simply place them under your monitors
or laptops to help prevent movement. Helpful Tip: Tacky friction pads
are reusable. Use water to wipe clean and reapply where needed.
Make sure your things are centered on the upper worksurface. Do not
place items on the edge where they could fall or throw off the bal-
ance of the converter.
Leave enough slack in your cables to allow for the converter to raise
and lower. If cables are too short they can snag and pull items off
your worksurface.
Adjustment Guide
In it’s lowest position, the upper worksurface sits
6.5’’ from the desk surface.
In it’s highest position, the upper worksurface sits
16.7’’ from the desk surface.
When not in use, ip
the tray up to store
it so that it is out of
the way.
The Keyboard tray rests at at 0°.
Flip up the tabs underneath the
tray, and the tray will rest at 8°.
UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Copyright Notice: These instructions are a component of the UPLIFT Front Clamp Standing Converter . These instructions are part of the scope of delivery, even if the item is resold. These instructions are
also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk.
These instructions are subject to United States copyright law.
©
!
!
!
!
!
!
!
CAUTION: Keep hands clear during operation! Do not reach into the mechanism near
the gas spring, or near the supporting bars.
CAUTION: Read all instructions before assembly. Failure to assemble properly may result
in damage or personal injury.
CAUTION: The maximum load capacity of the unit is 33 lbs for the upper worksurface
and 4 lbs for the keyboard tray. Do not overload.
CAUTION: Keep devices centered and away from the edge of the main worksurface,
to prevent them from falling.
CAUTION: Make sure that the wires for your devices have enough slack. This will prevent
your devices from being pulled off the unit workstation when raising the unit.
CAUTION: When relocating the unit, remove all devices to avoid harm or damage,
and adjust the unit to its lowest position.
CAUTION: When moving, move it carefully with two people, to avoid injury and damage
to the product and surroundings.
6.5’’
8°
0°
16.7’’