Uplift Desk UDA120~mobile User manual

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
®
UPLIFT Adapt Mobile™Instructions
UDA120~mobile
There are two ways to attach your UPLIFT Adapt Mobile™to your desktop: Clamp assembly, and bolt-thru assembly.
Clamp Assembly - Attach the arm to the back of your desk....
Clamp Step 1
Connect the top clamp (part 3) to the Adapt Mobile™ arm using the three
M6x12mm screws (part A) and the small Allen wrench.
Clamp Step 2
Place the Arm Gasket (part 2) under the arm mount, and the clamp gas-
kets (part 5) to the bottom clamp (part 6).
Clamp Step 3
Connect the bottom clamp assembly (part 6) to the top clamp assembly
by using M6x14mm (part C) and the small Allen wrench.
Clamp Step 4
Turn the knobs counterclockwise to loosen them.
Slide the assembly onto your desk and turn the knobs clockwise to
tighten the clamp to the desk. Make sure that the clamp is secure. If the
clamp is too loose, the unit may wobble or fall.
Snap the Cable cover (part 4) to the back.
Part 1
Adapt Mobile™ arm
Screws
Tools
Part 3
Top Clamp
Part 7
Bolt top clamp Part 12
Tray mount
Part 4
Cable Cover
Part 8
Bolt
Part 13
Mount cover
Part 5
Clamp Gaskets
(qty 2)
Part 9
Bolt gasket
Part 14 - Tray
Part 6
Bottom Clamp
Part 10
Bolt bottom clamp
Part 2
Arm gasket
Part 11
Bolt knob
Part A
M6x12mm screws
(qty 3)
Part B
M6x12mm screws
(qty 8)
Part C
M6x14mm screws
(qty 2)
Allen wrench
(small)
Allen wrench
(large)

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Step 2
Connect the tray mount (part 12) to the Adapt Mobile™ arm using four M6x-
12mm screws (part B) and tighten with the small Allen wrench (part 18).
Afx the mount cover (part 13) as shown.
Step 3
Connect the tray (part 14) to the tray mount (part 12) using four M6x12mm
screws (part B) and tighten with the small Allen wrench.
Bolt-Thru Step 1
Insert the long screw (part 8) into the bolt-thru top clamp (part 7)
Bolt-Thru Step 2
Connect the assembly to the Adapt Mobile™ arm using the three
M6x12mm screws (part A) and the small Allen wrench.
Bolt-Thru Step 3
Place the arm gasket (part 3) under the arm’s mount, and apply the place
the bolt gasket (part 9) onto the bolt bottom clamp (part 10) as shown.
Slide the arm assembly into the hole on your desk.
Bolt-Thru Step 4
Slide the the bolt bottom clamp (part 10) over the screw, then screw on
the bolt-thru knob (part 11) and tighten, to keep the Adapt Mobile™ arm
securely fastened to the desk. Make sure that the clamp is secure. If the
clamp is too loose, the unit may wobble or fall.
Bolt-Thru Assembly - for holes 8.5mm to 70mm

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
The UPLIFT Adapt Mobile allows you to run cables from your tray, down the arm,
and to the back of your desk.
a. Pull the four tabs out of the cable cover on the upper section of the arm
b. Pull up and out on the cable cover on the lower section of the arm
c. Run your cables through the exposed section of the arm. Make sure that there is some
slack in the cables to allow the arm to freely move.
d. Trap the cables under the cable cover on the upper section of the arm and snap it back
into place, and slide the cable cover over the wires in the lower section of the arm
Cord Management
a. b. c. d.
Moving the arm, and counterbalancing
180°
360°
270°
You can adjust the angle and position of your tray by simply moving it to
the position you desire. If you nd that the after you place your laptop on
the tray that it either lifts or drops, then you need to counterbalance your
UPLIFT Adapt Mobile.
With your laptop (or object of identical weight) on the tray, use the
large Allen wrench to adjust the tension adjustment screw located at the
middle joint of the arm. Turn toward the “-” if your arm will not adjust to
a lower position and turn toward the “+” if your arm will not adjust to a
higher position. When the arm stays in place after you’ve adjusted it, your
UPLIFT Adapt Mobile is properly counterbalanced.

®
Adapt Mobile™
by
Copyright Notice: These instructions are a component of the UPLIFT View ™ monitor arm . These instructions are part of the scope of delivery, even if the item is resold.
These instructions are also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published
form without the prior written consent of UPLIFT Desk.
These instructions are subject to United States copyright law.
©
•
•
•
•
•
•
The maximum load capacity of the UPLIFT Adapt
Mobile™is 15.4 lbs. Do not overload.
Leave cables slack in the arm assembly to allow the
arm room to adjust.
Secure all clamps and mounts to a stable desktop
NOT A CHILD’S TOY. Children under 12 must be
supervised by an adult while using UPLIFT Adapt
Mobile.
Failing to follow these assembly instructions
and safety precautions may result in personal injury.
Failing to follow these assembly instructions
and safety precautions voids your warranty
and may result in property damage.
CAUTION
!