Uplift Desk ACC301 User manual

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
®
View™ Monitor Arm Instructions
ACC301
There are two ways to attach your UPLIFT View™ Monitor Arm to your desktop: Clamp and Bolt-thru assembly.
Clamp Step 2
Apply the arm gasket (part 2) under the arm’s mount, and the clamp
gaskets (part 5) to the bottom clamp (part 6).
Clamp Step 1
Connect the top clamp (part 3) to the Adapt View™ arm assembly using
the three M6x12mm screws (part C) and the small Allen wrench (part G).
Clamp Step 3
Connect the bottom clamp assembly (part 6) by using M6x10mm (part D)
and the small Allen wrench (part H). Afx the Clamp gaskets as shown.
Clamp Step 4
Turn the knobs counterclockwise to loosen them.
Slide the assembly onto your desk and turn the knobs clockwise
to tighten the clamp to the desk. Make sure that the clamp is secure.
If the clamp is too loose, the unit may wobble or fall.
Snap the cable cover to the back.
Part 1
UPLIFT View™ arm
Part 4
Cable Cover
Part 3
Top Clamp
Part 7
Bolt top clamp
Part 2
Arm gasket
Part 8
Bolt
Part 5
Clamp Gasket
Part 9
Bolt gasket
Part 6
Bottom Clamp
Part 10
Bolt bottom clamp
Part 11
Bolt knob
Part A
M4x12mm screws
(qty 4)
Part F
Washers
(qty 8)
Part B
M5x12mm screws
(qty 4) Part G
Allen wrench
(small)
Part C
M6x12mm screws
(qty 3) Part H
Allen wrench
(large)
Part D
M6x10mm screws
(qty 2)
Please select the appropriate
mounting holes according
to the thickness of the desk.
Clamp Assembly - Attach the arm to the back of your desk
Screws & Tools

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Step 2
Use two washers (part F) and two screws* and screw them in by hand.
*Most monitors will use the M4x12 (part A) screws, but if those seem
loose to you, use the M5x12 (part B).
Step 3
Place the monitor onto the on the open holes on the Vesa plate.
See Fig. 1 for specic placement.
Fig. 1
Fig. 2
Step 4
Using 2 more washers and screws, screw into the lower two holes on the
Vesa mounting plate. (see Fig 2).
When nsihed, tighten up all screws from this step and step 2.
Bolt-Thru Assembly - for holes 8.5mm to 70mm
Bolt-Thru Step 1
Insert the long screw (part 8) into the bolt top clamp (part 7).
Bolt-Thru Step 2
Connect the assembly to the Adapt View™ arm using the three M6x12mm
screws (part C) and the small Allen wrench (part G).
Bolt-Thru Step 3
Place the arm gasket (part 2) under the arm’s mount, then slide the assem-
bly into the bolt on your desk. Place the bolt gasket (part 9) onto the bolt
bottom clamp (part 10) as shown.
Bolt-Thru Step 4
Slide bolt bottom clamp (part 10) onto the bolt, and screw on the bolt-thru
knob (part 11) and tighten, to keep the Adapt View™ arm securely fastened
to the desk. Make sure that the clamp is secure. If the clamp is too loose,
the unit may wobble or fall.

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
The UPLIFT Adapt View™line allows you to run cables from your tray, down the arm,
and to the back of your desk.
a. Pull the four tabs out of the cable cover on the upper section of the arm
b. Pull up and out on the cable cover on the lower section of the arm
c. Run your cables through the exposed section of the arm. Make sure that there is some
slack in the cables to allow the arm to freely move.
d. Trap the cables under the cable cover on the upper section of the arm and snap it back
into place, and slide the cable cover over the wires in the lower section of the arm
Using Cord Management
a. b.
Moving the arm, and counterbalancing
180°
360°
360°
270°
You can adjust the angle and position of your monitor by simply moving
it to the position you desire. If you nd that after you mount your monitor
that it either lifts or drops, then you need to counterbalance your UPLIFT
Adapt Mobile.
Use the large Allen wrench (part H) to adjust the tension adjustment screw
located at the middle joint of the arm. Turn toward the “-” if your arm will
not adjust to a lower position and turn toward the “+” if your arm will
not adjust to a higher position. When the arm stays in place after you’ve
adjusted it, your UPLIFT Adapt Mobile is properly counterbalanced.

®
Adapt View™ Monitor Arm
by
CAUTION
!
Copyright Notice: These instructions are a component of the UPLIFT View ™ Monitor Arm . These instructions are part of the scope of delivery, even if the item is resold.
These instructions are also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published
form without the prior written consent of UPLIFT Desk.
These instructions are subject to United States copyright law.
©
•
•
•
•
•
•
The maximum load capacity of the UPLIFT Adapt
View™monitor arm is 19.8 lbs. Do not overload.
Leave cables slack in the arm assembly to allow the
arm room to adjust.
Secure all clamps and mounts to a stable desktop
NOT A CHILD’S TOY. Children under 12 must be
supervised by an adult while using UPLIFT Adapt
View™.
Failing to follow these assembly instructions
and safety precautions may result in personal injury.
Failing to follow these assembly instructions
and safety precautions voids your warranty
and may result in property damage.