Uplus Lighting 37X15Z User manual

User manual
37X15Z WASH
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………4-5
DMX Channels ……………………………………………………………………………………6-12
Trouble Shooting…………………………………………………………………………………12
Fixture Cleaning………………………………………………………… ………………………13
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Power supply: 110-240V, 50/60HZ
Power consumption: 560W
Light source:37*15W 4in1 RGBW LED
DMX Channel: 24/36/48 CH
Zoom angle: 5°-60°
Horizontal scanning: 540° (16bit precision scanning) Electronic error correction
Vertical scanning: 270° (16bit precision scanning) Electronic error correction
Strobe: 1-25 times/S or random strobe
Dimming: 0-100% linear adjustment
Dimension: 42*33*26 cm, NW:13.5 kgs
Led ring control effect
3.Control Menu
Menu Operation
On the base of the control panel offers a number of features, such as setting DMX fixture address,
switch the lamp, run the test program, the mode selection.
Main Menu
Second
Third
Fourth
Dmx Address
000 - 512
Run Mode
Dmx512
0-255

5
Slow
Fast
Sound
Manual
Invert
Pan
Yes/No
Tilt
Yes/No
Display Set
Invert word
Yes/No
English/Chinese
LCD Backlight on
Yes
No
Manual Set
Pan
000 - 255
Panmico
000 - 255
Pan fining adjust
Tilt
000 - 255
TiltMICO
000 - 255
Tilt fining adjust
ZOOM
000 - 255
DIM
000 - 255
STROBE
000 - 255
DIM_R
000 - 255
DIM_G
000 - 255
DIM_B
000 - 255
DIM_W
000 - 255
Sound Sence
0-100
Sound Sensitivity adjust
System Set
Version information
Vxxx
Pan reset
Normal/wrong
Tilt Reset
Normal/wrong
Default settings
Code settings
Password:↓↓↑↑
Pan_INIT
Pan fine adjust
TILT_INIT
Tilt fine adjust
ZOOM_INIT
Zoom adjust
SET_R
RED color set
SET_G
Green color set
SET_B
Blue color set
SET_W
White color set
Reset

6
4. DMX Channels
48 CH Mode
CH
Function
DMX value
Description
1
Pan
0-255
0~540 adjust
2
Pan fine
0-255
16bit adjust
3
Tilt
0-255
0~270
4
Tilt fine
0-255
16bit 可调
5
Speed of pan/tilt
0-255
From fast to slow
6
Zoom
0-255
Zoom from small to big
7
Dimming
0-255
0-100% dark to bright
8
Strobe
0-9
No function
10-154
Synchronous strobe speed from slow to fast
（1HZ~25HZ）
155-204
Random strobe
205-255
Full strobe
9
LED1R Dimming
0-255
Zone 1 Red dimming from dark to bright
10
LED1GDimming
0-255
Zone 1 G dimming from dark to bright
11
LED1BDimming
0-255
Zone 1 B dimming from dark to bright
12
LED1WDimming
0-255
Zone 1 W dimming from dark to bright
13
LED2RDimming
0-255
Zone 2 Red dimming from dark to bright
14
LED2GDimming
0-255
Zone 2 G dimming from dark to bright
15
LED2BDimming
0-255
Zone 2 B dimming from dark to bright
16
LED2WDimming
0-255
Zone 2 W dimming from dark to bright
●
●
●
●
●
●
●
●
●
●
●
●
29
LED 6R Dimming
0-255
Zone 6 Red dimming from dark to bright
30
LED 6G Dimming
0-255
Zone 6 G dimming from dark to bright
31
LED 6B Dimming
0-255
Zone 6 B dimming from dark to bright
32
LED 6W Dimming
0-255
Zone 6 W dimming from dark to bright
33
LED 7R Dimming
0-255
Zone 7 Red dimming from dark to bright
34
LED 7G Dimming
0-255
Zone 7 G dimming from dark to bright
35
LED 7B Dimming
0-255
Zone 7 B dimming from dark to bright
36
LED 7W Dimming
0-255
Zone 7 W dimming from dark to bright
37
Priority 5:CTO
0-9
No function
10-255
10000K-2500K
38
Priority 4: Build
in color effect
0-9
No function
10-19
Effect 1
20-29
Effect 2
30-39
Effect 3
40-49
Effect 4

7
50-59
Effect 5
60-69
Effect 6
70-79
Effect 7
80-89
Effect 8
90-99
Effect 9
100-109
Effect 10
110-119
Effect 11
120-129
Effect 12
130-139
Effect 13
140-149
Effect 14
150-159
Effect 15
160-169
Effect 16
170-179
Effect 17
180-189
Effect 18
190-199
Effect 19
200-209
Effect 20
210-224
Color jump change(build-in effect)
225-239
Color pulse change (build-in effect)
240-255
Color fade change (build-in effect)
39
Priority 3: Static
pattern effect
0-9
No function
10-19
Effect 1
20-29
Effect 2
30-39
Effect 3
40-49
Effect 4
50-59
Effect 5
60-69
Effect 6
70-79
Effect 7
80-89
Effect 8
90-99
Effect 9
100-109
Effect 10
110-119
Effect 11
120-129
Effect 12
130-139
Effect 13
140-149
Effect 14
150-159
Effect 15
160-169
Effect 16
170-179
Effect 17
180-189
Effect 18
190-199
Effect 19
200-209
Effect 20
210-255
Static pattern effect (build-in effect)
40
Priority 2: dynamic
effect
0-9
No function
10-255
Per 12 DMX value one effect, total 20 types
effect
41
Back light R
0-255
0~255 control(39CH,40CH)back light

8
42
Back light G
0-255
0~255 control(39CH,40CH)back light
43
Back light B
0-255
0~255 control(39CH,40CH)back light
44
Back light W
0-255
0~255 control(39CH,40CH)back light
45
Adjust effect direction
0-127
Dynamic pattern Positive direction
128-255
Dynamic pattern opposite direction
46
Effect speed
0-255
from fast to slow
47
Priority 1:Marco
function
0-9
No function
10-99
Auto run 1
100-199
Auto run 2
200-255
Sound mode
48
Reset
0-239
No function
240-250
reset,valid in 3S
251-255
No function
36 CH Mode
CH
Function
DMX value
Description
1
Pan
0-255
0~540 adjust
2
Pan fine
0-255
16bit adjust
3
Tilt
0-255
0~270
4
Tilt fine
0-255
16bit 可调
5
Speed of pan/tilt
0-255
From fast to slow
6
Zoom
0-255
Zoom from small to big
7
Dimming
0-255
0-100% dark to bright
8
Strobe
0-9
No function
10-154
Synchronous strobe speed from slow to fast
（1HZ~25HZ）
155-204
Random strobe
205-255
Full strobe
9
LED1R Dimming
0-255
Zone 1 Red dimming from dark to bright
10
LED1G Dimming
0-255
Zone 1 G dimming from dark to bright
11
LED1B Dimming
0-255
Zone 1 B dimming from dark to bright
12
LED1W Dimming
0-255
Zone 1 W dimming from dark to bright
13
LED2R Dimming
0-255
Zone 2 Red dimming from dark to bright
14
LED2G Dimming
0-255
Zone 2 G dimming from dark to bright
15
LED2B Dimming
0-255
Zone 2 B dimming from dark to bright
16
LED2W Dimming
0-255
Zone 2 W dimming from dark to bright
17
LED3R Dimming
0-255
Zone 3 Red dimming from dark to bright
18
LED3G Dimming
0-255
Zone 3 G dimming from dark to bright
19
LED3B Dimming
0-255
Zone 3 B dimming from dark to bright
20
LED3W Dimming
0-255
Zone 3 W dimming from dark to bright
21
LED4R Dimming
0-255
Zone 4 Red dimming from dark to bright

9
22
LED4 G Dimming
0-255
Zone 4 G dimming from dark to bright
23
LED4 B Dimming
0-255
Zone 4 B dimming from dark to bright
24
LED4 W Dimming
0-255
Zone 4 W dimming from dark to bright
25
Priority 5:CTO
0-9
No function
10-255
10000K-2500K
26
Priority 4: Build
in color effect
0-9
No function
10-19
Effect 1
20-29
Effect 2
30-39
Effect 3
40-49
Effect 4
50-59
Effect 5
60-69
Effect 6
70-79
Effect 7
80-89
Effect 8
90-99
Effect 9
100-109
Effect 10
110-119
Effect 11
120-129
Effect 12
130-139
Effect 13
140-149
Effect 14
150-159
Effect 15
160-169
Effect 16
170-179
Effect 17
180-189
Effect 18
190-199
Effect 19
200-209
Effect 20
210-224
Color jump change(build-in effect)
225-239
Color pulse change (build-in effect)
240-255
Color fade change (build-in effect)
27
Priority 3: Static
pattern effect
0-9
No function
10-19
Effect 1
20-29
Effect 2
30-39
Effect 3
40-49
Effect 4
50-59
Effect 5
60-69
Effect 6
70-79
Effect 7
80-89
Effect 8
90-99
Effect 9
100-109
Effect 10
110-119
Effect 11
120-129
Effect 12
130-139
Effect 13
140-149
Effect 14
150-159
Effect 15
160-169
Effect 16

10
170-179
Effect 17
180-189
Effect 18
190-199
Effect 19
200-209
Effect 20
210-255
Static pattern effect (build-in effect)
28
Priority 2: dynamic
effect
0-9
No function
10-255
Per 12 DMX value one effect, total 20 types
effect
29
Back light R
0-255
0~255 control(27CH,28CH)back light
30
Back light G
0-255
0~255 control(27CH,28CH)back light
31
Back light B
0-255
0~255 control(27CH,28CH)back light
32
Back light W
0-255
0~255 control(27CH,28CH)back light
33
Adjust effect direction
0-127
Dynamic pattern Positive direction
128-255
Dynamic pattern opposite direction
34
Effect speed
0-255
from fast to slow
35
Priority 1:Marco
Function
0-9
No function
10-99
Auto run 1
100-199
Auto run 2
200-255
Sound Mode
36
Reset
0-239
No function
240-250
reset,valid in 3S
251-255
No function
24 CH Mode
CH
Function
DMX value
Description
1
Pan
0-255
0~540 adjust
2
Pan fine
0-255
16bit adjust
3
Tilt
0-255
0~270
4
Tilt fine
0-255
16bit 可调
5
Speed of pan/tilt
0-255
From fast to slow
6
Zoom
0-255
Zoom from small to big
7
Dimming
0-255
0-100% dark to bright
8
Strobe
0-9
No function
10-154
Synchronous strobe speed from slow to fast
（1HZ~25HZ）
155-204
Random strobe
205-255
Full strobe
9
R dimming
0-255
From dark to bright
10
G dimming
0-255
From dark to bright
11
B dimming
0-255
From dark to bright
12
W dimming
0-255
From dark to bright
13
Priority 5:
CTO
0-9
No function
10-255
10000K-2500K

11
14
Priority 4: Build
in color effect
0-9
No function
10-19
Effect 1
20-29
Effect 2
30-39
Effect 3
40-49
Effect 4
50-59
Effect 5
60-69
Effect 6
70-79
Effect 7
80-89
Effect 8
90-99
Effect 9
100-109
Effect 10
110-119
Effect 11
120-129
Effect 12
130-139
Effect 13
140-149
Effect 14
150-159
Effect 15
160-169
Effect 16
170-179
Effect 17
180-189
Effect 18
190-199
Effect 19
200-209
Effect 20
210-224
Color jump change(build-in effect)
225-239
Color pulse change (build-in effect)
240-255
Color fade change (build-in effect)
15
Priority 3: Static
pattern effect
0-9
No function
10-19
Effect 1
20-29
Effect 2
30-39
Effect 3
40-49
Effect 4
50-59
Effect 5
60-69
Effect 6
70-79
Effect 7
80-89
Effect 8
90-99
Effect 9
100-109
Effect 10
110-119
Effect 11
120-129
Effect 12
130-139
Effect 13
140-149
Effect 14
150-159
Effect 15
160-169
Effect 16
170-179
Effect 17
180-189
Effect 18
190-199
Effect 19
200-209
Effect 20
210-255
Static pattern effect (build-in effect)

12
16
Priority 2: dynamic
effect
0-9
No function
10-255
Per 12 DMX value one effect, total 20 types
effect
17
Back light R
0-255
0~255 control(15CH,16CH)back light
18
Back light G
0-255
0~255 control(15CH,16CH)back light
19
Back light B
0-255
0~255 control(15CH,16CH)back light
20
Back light W
0-255
0~255 control(15CH,16CH)back light
21
Adjust effect direction
0-127
Dynamic pattern Positive direction
128-255
Dynamic pattern opposite direction
22
Speed of effect
0-255
From fast to slow
23
Priority 1：Marco
function
0-9
NO function
10-99
Auto Run 1
100-199
Auto Run 2
200-255
Sound Mode
24
Reset
0-239
No function
240-250
reset,valid in 3S
251-255
No function
6.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition

13
7.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.