Uplus Lighting 7X40 B EYE User manual

User manual
7X40 B EYE
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions…………………………………………………………………………………3
Technical Specifications……………………………………………………………………………4
Control Menu ………………………………………………………………………………………5-6
DMX Channels …………………………………………………………………………………7-11
Dimension ……………………………………………………………………………………12
Lumen data ……………………………………………………………………………………12
Trouble Shooting……………………………………………………………………………………13
Fixture Cleaning………………………………………………………… …………………………13
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also
receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power requirements of the
unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its
base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than this Unit
surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its operation. Turn off
the power and allow about 15 minutes for the unit to cool down before replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized
technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself. In
the unlikely event your unit may require service, please contact your nearest dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid
vibration and slipping while operating. And make sure that the structure to which you are attaching the unit is
secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can
hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of
people.

4
2.Technical Specifications
Input Voltage: 100-240V, 50/60Hz
Power consumption: 300W
Power supply: 350W
Single LED power: 40W
Light source: 7x40W RGBW 4IN LED
Beam angle: 4-60°
Adjustable color temperature
DMX Channel: 23/35/51CH
Operate mode: DMX512, AUTO master/slave, Voice control，RDM
Electronic dimmer:0～100% linear
Linear CTO color temperature adjustment: 2500-8000K
Three phase silent motor fast and stable
Fast operation speed and noiseless operation
Fixture size: 338*256*449.5mm

5
3.Control Menu
First interface
Description
Explain
Address
001 - 512
Button up and down: Change the address code of
this light, for example, if the channel value is 23CH,
then the address code of this light is 1, and the
address code of the next light is 24; Left and right
buttons: Each time the address code of this light
increases by 1 or the address code decreases by 1
Signal
ON/OFF
DMX signal
Channel
21CH/23CH/35CH
Mode
DMX512/Auto1/auto2/so
und
Current operating mode of the LED
TEMP
20℃
Current temperature of the LED
**℃
Abnormal temperature display
Reset
information
Display reset status
1) Normal
2) Exception: Reset the specific content of the
exception. View the information options on the
setting interface
Menu
Description
Explain
Address
address：001 - 512
Same interface menu structure operation
Adjust
Enter password
LED calibration
ON/OFF
ON/OFF
Change Language
Normal
Normal
Screen does not display in reverse
Invert
Screen inversion display
Auto
The system can automatically rotate the screen
according to the direction of gravity
Setup
Setup
Enter the settings interface
Main Menu
Secondary menu
tertiary menu/parameters
Address
001 - 512
System settings
Run mode
DMX/sound/auto1/auto2
Channel
23CH/35CH/51CH
Pan def Pos
000
Tilt def Pos
127
Invert pan
on/off
Invert Tilt
on/off
Swap pan/tilt
on/off
Fast dimming
on/off
KEEP Signal
on/off/auto

6
Encoder Correct
on/off
Hall correct
ON/OFF
Back lighting time
15s/30s/LOGO/OFF
Curve
Curve1/Curve2/
Curve3/Curve4
Load default
OK/Cancel
Adjust
Enter password
xxxx
TEST
Current channel mode
Channel
0-255
Reset
Motor ON/OFF
Reset Head
Reset XY
Reset ALL
Info
Error message
Display specific information content
DMX data
Display specific testing content for DMX
Sensor info
Display specific information of optocoupler and Hall
Version
Display version number and RDM code
Usage time
xxxxH

7
4.DMX Channels
23CH
CH
Function
DMX value
Description
1
X
0-255
X rotate
2
X fine
0-255
X-axis fine adjustment
3
Y
0-255
Y rotate
4
Y fine
0-255
Y-axis fine adjustment
5
XY speed
0-255
Fast-slow
6
zoom
0-255
Angle From large to small
7
rotating
0-127
0-60 degree
128-188
Antiwise fast-slow
189-193
Stop
194-255
Forward slow-fast
8
dimmer
0-255
Linear dimming from dark to light
9
strobe
0-3
OFF
4-103
Synchronous strobe speed from slow to fast (1HZ-25HZ)
104-107
Open
108-207
Split the strobe speed from slow to fast (1HZ-25HZ)
208-212
Open
213-225
Low speed random strobe
226-238
Medium speed random strobe
239-251
High speed random strobe
252-255
Open
10
R
0-255
From dark-bright
11
G
0-255
From dark-bright
12
B
0-255
From dark-bright
13
W
0-255
From dark-bright
14
CT
0-255
Linear CT control
15
Color Macro
0-255
Inner color gradual change
16
Static
effects
0-255
5 no. One effect
17
Dynamic
effects
0-255
5 no. One effect
18
Dynamic
effects
Speed
0-127
Forward from fast-slow
128-255
Reverse from slow-fast
19
Background
R
0-255
Dark-bright

8
20
Background
G
0-255
Dark-bright
21
Background
B
0-255
Dark-bright
22
Background
W
0-255
Dark-bright
23
reset
0-79
No function
80-99
Curve 1 (5s)
100-119
Curve 2 (5s)
120-139
Curve 3 (5s)
140-159
Curve 4 (5s)
160-179
Slow dimming mode (5s)
180-199
Fast dimming mode (5s)
200-209
Effect motor reset (5s)
210-219
XY motor reset (5s)
220-229
Reset all motors (5s)
35CH
CH
Function
DMX value
Description
1
R
0-255
Red dimmer
2
R Fine
0-255
Red dimmer fine
3
G
0-255
Green dimmer
4
G Fine
0-255
Green dimmer fine
5
B
0-255
Blue dimmer
6
B fine
0-255
Blue dimmer fine
7
W
0-255
White dimmer
8
W Fine
0-255
White dimmer fine
9
CT
0-255
Linear CT control
10
Color Macro
0-255
Color Macro function
11
strobe
0-3
off
4-103
Synchronous strobe slow-fast （1HZ-25HZ）
104-107
on
108-207
Divide strobe from slow-fast （1HZ-25HZ）
208-212
on
213-225
Random strobe in low speed
226-238
Random strobe in middle speed
239-251
Random strobe in high speed
252-255
on
12
dimmer
0-255
Linear dimmer from dark-bright

9
13
Dimmer Fine
0-255
Dimmer fine
14
X
0-255
pan
15
X fine
0-255
Pan fine
16
Y
0-255
tilt
17
Y fine
0-255
Tilt fine
18
function
0-255
reserve
19
reset
0-79
No function
80-99
Curve 1 (5s)
100-119
Curve 2 (5s)
120-139
Curve 3 (5s)
140-159
Curve 4 (5s)
160-179
Slow dimming mode (5s)
180-199
Fast dimming mode (5s)
200-209
Effect motor reset (5s)
210-219
XY motor reset (5s)
220-229
Reset all motors (5s)
20
zoom
0-255
zoom
21
rotating
0-127
0-60 degree
128-188
Antiwise fast-slow
189-193
Stop
194-255
Forward slow-fast
22
pattern
0-255
Pattern rotate
23
Pattern
speed
0-255
Pattern speed
24
Pattern
effect fade
0-255
Pattern effect fade
25
Pattern
effect R
0-255
Pattern effect R
26
Pattern
effect G
0-255
Pattern effect G
27
Pattern
effect B
0-255
Pattern effect B
28
Pattern
effect W
0-255
Pattern effect W
29
Pattern
dimmer
0-255
Pattern 0-100% dimmer
30
Background
dimmer
0-255
Background 0-100% dimmer
31
Pattern
Transition
0-255
Pattern change control
32
Pattern
angle
0-255
Pattern translation

10
51CH
CH
Function
DMX value
description
1
X
0-255
pan
2
X fine
0-255
Pan fine
3
Y
0-255
tilt
4
Y fine
0-255
Tilt fine
5
XY speed
0-255
Fast-slow
6
zoom
0-255
Small-big
7
rotating
0-127
0-60 degree
128-188
Antiwise fast-slow
189-193
Stop
194-255
Forward slow-fast
8
dimmer
0-255
Dark-bright
9
strobe
0-3
off
4-103
Synchronous strobe slow-fast （1HZ-25HZ）
104-107
on
108-207
Divide strobe from slow-fast （1HZ-25HZ）
208-212
on
213-225
Random strobe in low speed
226-238
Random strobe in middle speed
239-251
Random strobe in high speed
252-255
on
10
R dimmer
0-255
11
G dimmer
0-255
12
B dimmer
0-255
13
W dimmer
0-255
14
CT
0-255
Linear CT control
15
Wash
0-255
16
Static effect
0-255
5 no. One effect
17
Dynamic effect
0-255
5 no. One effect
adjustment
33
Prospect
strobe
0-255
Prospect strobe（with 11 chs）
34
Background
strobe
0-255
Background strobe（with 11 chs）
35
Background
selection
0-255
Background selection

11
18
Dynamic effect
speed
0-127
Forward fast-slow
128-255
Reverse slow-fast
19
Background R
0-255
Dark-bright
20
Background G
0-255
Dark-bright
21
Background B
0-255
Dark-bright
22
Background W
0-255
Dark-bright
19
reset
0-79
No function
80-99
Curve 1 (5s)
100-119
Curve 2 (5s)
120-139
Curve 3 (5s)
140-159
Curve 4 (5s)
160-179
Slow dimming mode (5s)
180-199
Fast dimming mode (5s)
200-209
Effect motor reset (5s)
210-219
XY motor reset (5s)
220-229
Reset all motors (5s)
24
R1 LED
dimmer
0-255
R1 LED dimmer
25
G1 LED
dimmer
0-255
G1 LED dimmer
26
B1 LED
dimmer
0-255
B1 LED dimmer
27
W1 LED
dimmer
0-255
W1 LED dimmer
…
…
……
……
…
…
……
……
48
R7 LED
dimmer
0-255
R7 LED dimmer
49
G7 LED
dimmer
0-255
G7 LED dimmer
50
B7 LED
dimmer
0-255
B7 LED dimmer
51
W7 LED
dimmer
0-255
W7 LED dimmer

12
5.Dimension
6.Lumen data

13
7.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
8.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.