Uplus Lighting BSW 280 User manual

User manual
BSW 280
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………5-6
DMX Channels ……………………………………………………………………………………6-10
Trouble Shooting…………………………………………………………………………………11
Fixture Cleaning………………………………………………………… ………………………12
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Ballast: E-ballast
Light source: 280w White
Color temperature: 9300 k
beam angle:3.8°-20°
Pan scan：540°(16bit) Electric correction
Tilt scan：270°(16bit) Electric correction
Voltage: AC110-240v
Frequency: 50 /60 hz
Total power: 300 w
Amazing dot matix, four tact switch, 180°turning show
Color wheel: one color wheel, 13 kinds of color chips in one color wheel
Static Gobo: 14gobos
Rotation Gobo:9 gobos
Effect Wheel: one Rotation eight prism,one Rotation six prism effect move , frost
strobe macro control available.
The linear dimming: 0-100% dimmer
Control signal: international standard DMX512
Channel mode: 16/24 channel model
Protection grade: IP20
Dimension:360*240*460mm
NW:16.65kgs
Packing Size: 470*470*600mm
G.W：19.1KG

5
3.Control Menu
Menu Operation
On the base of the control panel offers a number of features, such as setting DMX fixture address,
switch the lamp, run the test program, the mode selection.
DMX Address
001-512
RUN MODE
DMX 16 channel
DMX 24 channel
Auto Run
Sound Control
Master/Slaver mode
Light Switch
sure
no
Channel Qty
simple
expand
Display Setting
language
Chinese
English
Screen Saver
mode 1
mode 2
mode 3
off
Screen Rotation
on
off
Touch Enable
on
off
Touch Rectify
Test
Pan
Tilt
Focus
Color
Gobo

6
Prism
Frost
Strobe
Advanced setup
Pan invert
on
off
Tilt invert
on
off
P/T rectify
on
off
Pan Offset
Tilt Offset
lamp up when
reset done
power on
manual
Factory setting
sure
no
Statue setup
work mode
address
version
elapse
total
DMX clr
Sys Rst
4.DMX Channels
Model - CH16/CH24
CH NO
Name
value
Function
1
2
1
1
X
0~255
Pan movement by 540°
2
X fine
0~255
Fine Pan
3
2
Y
0~255
Tilt movement by 270°
4
Y fine
0~255
Fine Tilt
5
3
XY speed
0~255
Speed from max. to min. (vector mode)
6
4
power/macro
0~129 empty
130~139
Lamp On,reset(total reset except pan/tilt
reset)
140~149
Pan/Tilt reset
150~189
Effect motor reset
200~209
Total reset
210~229
empty
230~239
Lamp Off

7
240~255
empty
7
5
colour
0~8
Open/white （100%~10%）
9~17
colour 1（100%~10%）
18~26
colour2（100%~10%）
27~36
Colour 3（100%~10%）
37~45
Colour 4（100%~10%）
46~54
Colour 5（100%~10%）
55~63
Colour 6（100%~10%）
64~72
Colour 7（100%~10%）
73~81
Colour 8（100%~10%）
82~90
Colour 9（100%~10%）
91~100
Colour 10（100%~10%）
101~109
Colour 11（100%~10%）
110~118
Colour 12（100%~10%）
119~127
Colour 13（110%~10%）
128~129
open/white
130~134
Colour 1
135~138
Colour 2
139~143
Colour 3
144~147
Colour 4
148~152
Colour 5
153~157
Colour 6
158~161
Colour 7
162~166
Colour 8
167~171
Colour 9
172~176
Colour 10
177~180
Colour 11
181~185
Colour 12
186~189
Colour 13
190~215
Forwards rainbow effect from fast to
slow
216~217
open/white
218~243
Backwards rainbow effect from slow to
fast
244~255
Auto random color selection from fast to
slow
8
Colour fine
0~255
Color wheel - fine positioning
9
6
speed
0~255
Speed of Rot. Gobo selection from
max. to min.
10
7
Static gobo
0~3
Open/hole
4~9
Gobo 1
10~15
Gobo 2
16~21
Gobo 3
22~27
Gobo 4
28~33
Gobo 5

8
34~39
Gobo 6
40~45
Gobo 7
46~51
Gobo 8
52~57
Gobo 9
58~63
Gobo 10
64~69
Gobo 11
70~75
Gobo 12
76~81
Gobo 13
82~87
Gobo 14
88~95
Shaking gobo 1 from slow to fast
96~103
Shaking gobo 2 from slow to fast
104~111
Shaking gobo 3 from slow to fast
112~119
Shaking gobo 4 from slow to fast
120~127
Shaking gobo 5 from slow to fast
128~135
Shaking gobo 6 from slow to fast
136~143
Shaking gobo 7 from slow to fast
144~151
Shaking gobo 8 from slow to fast
152~159
Shaking gobo 9 from slow to fast
160~167
Shaking gobo 10 from slow to fast
168~175
Shaking gobo 11 from slow to fast
176~183
Shaking gobo 12 from slow to fast
184~191
Shaking gobo 13 from slow to fast
192~199
Shaking gobo 14 from slow to fast
200~201
Beam
202~221
Forwards gobo wheel rotation from
fast to slow
222~223
No rotation
224~243
Backwards gobo wheel rotation from
slow to fast
244~255
Auto random gobo selection from fast
to slow
11
8
Rotation gobo
0~4
Open/hole
5~7
Gobo 1
8~10
Gobo 2
11~13
Gobo 3
14~16
Gobo 4
17~19
Gobo 5
20~22
Gobo 6
23~25
Gobo 7
26~28
Gobo 8
29~31
Gobo 9
Rotation
32~34
Rotation gobo 1
35~37
Rotation gobo 2
38~40
Rotation gobo 3

9
41~43
Rotation gobo 4
44~46
Rotation gobo 5
47~49
Rotation gobo 6
50~52
Rotation gobo 7
53~55
Rotation gobo 8
56~59
Rotation gobo 9
Shaking gobos
60~67
Shaking gobo 1 from slow to fast
68~75
Shaking gobo 2 from slow to fast
76~83
Shaking gobo 3 from slow to fast
84~91
Shaking gobo 4 from slow to fast
92~99
Shaking gobo 5 from slow to fast
100~107
Shaking gobo 6 from slow to fast
108~115
Shaking gobo 7 from slow to fast
116~123
Shaking gobo 8 from slow to fast
124~129
Shaking gobo 9 from slow to fast
Rotation Shaking gobos
130~137
Rotation Shaking gobo 1 from slow to
fast
138~145
Rotation Shaking gobo 2 from slow to
fast
146~153
Rotation Shaking gobo 3 from slow to
fast
154~161
Rotation Shaking gobo 4 from slow to
fast
162~169
Rotation Shaking gobo 5 from slow to
fast
170~177
Rotation Shaking gobo 6 from slow to
fast
178~185
Rotation Shaking gobo 7 from slow to
fast
186~193
Rotation Shaking gobo 8 from slow to
fast
194~199
Rotation Shaking gobo 9 from slow to
fast
200~201
Open/hole
202~221
Forwards gobo wheel rotation from
fast to slow
222~223
Open/hole
224
Forwards
225~243
Backwards gobo wheel rotation from
slow to fast
244~255
Auto random gobo selection from fast
to slow
12
9
Gobo rotation
rotation pattern channel set to index location
0~255
0~200°

10
When the rotation pattern is set to the stream channel
0
no rotation
1~127
Forwards gobo wheel rotation from
fast to slow
128~129
no rotation
130~255
Backwards gobo wheel rotation from
slow to fast
13
no
no rotation
14
10
prism
0~19
Open position (hole)
20~49
6-face linear rotating prism -indexing
50~75
6-face linear rotating prism- rotation
76~105
8-face circular rotating prism- Indexing
106~127
8-face circular rotating prism-rotation
Prism/gobo macros
128~135
Macro 1
136~143
Macro 2
144~151
Macro 3
152~159
Macro 4
160~167
Macro 5
168~175
Macro 6
176~183
Macro 7
184~191
Macro 8
192~199
Macro 9
200~207
Macro 10
208~215
Macro 11
216~223
Macro 12
224~231
Macro 13
232~239
Macro 14
240~247
Macro 15
248~255
Macro 16
15
11
Prism rotation
circular rotating prism- Indexing
0~255
0~200°
circular rotating prism-rotation
0
No rotation
1~127
Forwards prism rotation from fast to
slow
128~129
No rotation
130~255
Backwards prism rotation from slow to
fast
16
12
frost
0~127
Open/hole
128~255
frost
17
13
zoom
0~255
Zoom from max. to min.beam angle
18
Zoom fine
0~255
Fine Zoom
19
14
focus
0~255
Continuous adjustment from far to near
20
Focus fine
0~255
Fine Focus
21
no
N/A

11
22
15
shutter
0~31
Shutter closed
32~63
Shutter open
64~95
Strobe-effect from slow to fast
96~127
open
128~159
Opening pulse in sequences from slow
to fast
160~191
open
192~223
Random strobe-effect from slow to fast
224~255
open
23
16
dimmer
0~255
0~100%dimmer
24
no
N/A
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition

12
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.