Urban Electric LYFORD WALL Quick start guide

TS-1010
LYFORD WALL
ASSEMBLY AND MOUNTING INSTRUCTIONS
GENERAL NOTES
COMPONENTS PROVIDED FOR INSTALLATION
• THIS LUMINAIRE IS SUITED FOR WET LOCATIONS.
• THIS LUMINAIRE IS UL LISTED. WHEN INSTALLING LUMINAIRE, CONFORM
TO ALL APPLICABLE LOCAL ELECTRICAL CODES, ORDINANCES, AND THE
NATIONAL ELECTRICAL CODE (NEC).
• FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ AND
UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE COMMENCING
INSTALLATION OF THIS LUMINAIRE.
• CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
• THIS PRODUCT IS RATED ONE 60W MAX, TYPE B BULB(S).
• SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED ELECTRICIAN.
WARNING
THE ELECTRICITY MUST BE TURNED OFF AT THE MAIN FUSE BOX BEFORE
INSTALLING THIS LUMINAIRE. TURNING THE POWER OFF USING THE LIGHT
SWITCH MAY NOT BE SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
WOOD SCREWS MOUNTING PLATE WIRE NUTS WALL ANCHORS
CANDELABRA BULB(S) HEX WRENCH
SUNLIGHT- 25R14FL-MED
REFLECTOR FLOOD- INDOOR R14
25 WATT-120V
SUNLIGHT- CAT # 01910
CANDELABRA BASE-25T6/CL BULB
25 WATT-120V CLEAR
SUNLIGHT- CAT # 01929
CANDELABRA BASE-25T8/CL BULB
25 WATT-120V CLEAR
SUNLITE- 40CFC CAT# 01345
CANDELABRA-BASE FLAME TIP
40 WATT-120V CLEAR
SUNLIGHT- CAT # 01105
HOUSEHOLD CLEAR
60 WATT-120
60A/CL
SUNLIGHT- 60CTC CAT # 01395
CANDELABRA BASE-TORPEDO TIP
60 WATT-120V CLEAR
SUNLIGHT- CAT # 01216
SILVER BOWL-A-19/CLEAR BULB
100 WATT-120/130V GLARE FREE
100ASB-SU
FERROWATT
40 WATT-120V CLEAR
SUNLIGHT- CAT # 03470
MEDIUM BASE-MR16 BULB
50 WATT-120V HALOGEN
SUNLIGHT
COMPACT FLUORESCENT
13 WATT-120V
SL13SP65-SU
SUNLITE-COMPACT FLOURESCENT
SLC14TW/30K
14 WATT-(INCANDESCENT EQUIVALENT 60 WATT)
CAT # 65700 WARM WHITE
SUNLIGHT- CAT # 05510
COMPACT FLUORESCENT
25 WATT- INCANDESCENT EQUIVALENT-100 WATTS
SLS25/65K-BX
WESTINGHOUSE # 03840
WHITE 580 LUMENS
60 WATT-120V
WESTINGHOUSE-TUBULAR-25W
STANDARD BASE
25 WATT-120V
03835 25T10/F

LYFORD WALL
ASSEMBLY AND MOUNTING INSTRUCTIONS TS-1010
MOUNTING INSTRUCTIONS
MOUNTING DIAGRAM ELECTRICAL CONFIGURATION TABLE
FROM HOME FROM LUMINAIRE
CONNECT BLACK OR RED (HOT)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE ROUND WIRE (HOT)
CONNECT WHITE (NEUTRAL)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE RIBBED WIRE
(NEUTRAL)
CONNECT GREEN INSULATED OR BARE COPPER (GROUND -) HOUSE
SUPPLY CIRCUIT WIRE AND LUMINAIRE BARE STRANDED WIRE
(GROUND -) TO GREEN GROUND SCREW ON CROSSBAR.
GENERAL NOTE: USE UL LISTED WIRE NUTS FOR THE
WIRING CONNECTIONS IN THIS LUMINAIRE. WRAP WIRE NUT
CONNECTIONS WITH UL LISTED ELECTRICAL TAPE.
FOR QUESTIONS, PLEASE CONTACT CLIENT SERVICES AT:
843.723.8140 OR [email protected]
STEP 1
SHUT OFF THE MAIN ELECTRICAL SUPPLY TO THE JUNCTION
BOX FROM THE FUSE BOX/CIRCUIT BREAKER. TURNING POWER
OFF AT THE SWITCH IS NOT SUFFICIENT.
STEP 2
REMOVE MOUNTING PLATE FROM THE BACK OF THE FIXTURE
USING THE HEX WRENCH PROVIDED AND SET FIXTURE AND SET
SCREWS ASIDE.
STEP 3
LOCATE JUNCTION BOX AND PULL HOUSE SUPPLY CIRCUIT
WIRING THROUGH THE WIRE-WAY HOLE OF THE MOUNTING
PLATE. ATTACH THE MOUNTING PLATE DIRECTLY TO THE
JUNCTION BOX AND/OR DIRECTLY TO THE WALL SURFACE
USING THE MOUNTING SCREWS AND EXPANSION ANCHORS
PROVIDED. IT IS IMPORTANT TO CHECK LEVEL ON THE
MOUNTED WALL PLATE.
STEP 4
USING THE WIRE NUTS PROVIDED, MAKE ELECTRICAL
CONNECTIONS BY FOLLOWING THE ELECTRICAL CONFIGURATION
TABLE BELOW. ENSURE THAT ALL ELECTRICAL CONNECTIONS
ARE WRAPPED WITH UL-LISTED ELECTRICAL TAPE.
STEP 5
ATTACH THE FIXTURE TO THE MOUNTING PLATE BY SLIDING THE
FIXTURE OVER THE TOP OF THE MOUNTING PLATE AND THEN
SECURE THE FIXTURE AT THE BOTTOM WITH THE SET SCREWS
PROVIDED. BE CAREFUL TO AVOID SCRATCHING THE FINISH ON
THE FIXTURE.
STEP 6
INSTALL LIGHT BULB/S IN FIXTURE SOCKET AND RESTORE
POWER TO THE CIRCUIT. CONFIRM PROPER OPERATION OF THE
LIGHT FIXTURE.