Urban Electric MALPLAQUET FLUSHMOUNT Quick start guide

MALPL A Q UET F L USHM O U NT
MALPL A Q UET F L USHM O U NTMALPL A Q UET F L USHM O U NT
MALPL A Q UET F L USHM O U NT
ASSEMBLY AND MOUNTING INSTRUCTIONS S G - 1 2 2 9
G E N ER A L N O T E S
G E N ER A L N O T E SG E N ER A L N O T E S
G E N ER A L N O T E S
•THIS LUMINAIRE IS SUITED FOR DAMP LOCATIONS.
•THIS LUMINAIRE IS UL LISTED. WHEN INSTALLING LUMINAIRE,
CONFORM TO ALL APPLICABLE LOCAL ELECTRICAL CODES,
ORDINANCES, AND THE NATIONAL ELECTRICAL CODE (NEC).
•FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ
AND UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE
COMMENCING INSTALLATION OF THIS LUMINAIRE.
•CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
•THIS PRODUCT IS RATED FOR TWO 0W MAX, TYPE A BULB.
•SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
CAUTIONCAUTION
CAUTION
•THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED
ELECTRICIAN. PLEASE WEAR GLOVES TO PROTECT THE FINISH OF
THE FIXTURE.
WARNING
WARNINGWARNING
WARNING
THE ELECTRICITY MUST BE TURNED OFF AT THE MAIN FUSE BOX
BEFORE INSTALLING THIS LUMINAIRE. TURNING POWER OFF USING THE
LIGHT SWITCH MAY NOT BE SUFFICIENT TO PREVENT ELECTRICAL
SHOCK.
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A T I O N
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A T I O NC O M P O N E N T S P R O V I D E D F O R I N S T A L L A T I O N
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A T I O N
MOUNTING
MOUNTING MOUNTING
MOUNTING
ASSEMBLY
ASSEMBLYASSEMBLY
ASSEMBLY
CAGE
CAGE CAGE
CAGE
ASSEMBLY
ASSEMBLYASSEMBLY
ASSEMBLY
GLASS BOWL
GLASS BOWLGLASS BOWL
GLASS BOWL
HOUSEHOLD BULB
HOUSEHOLD BULBHOUSEHOLD BULB
HOUSEHOLD BULB
WIRE NUTS
WIRE NUTSWIRE NUTS
WIRE NUTS

MALPL A Q UET F L USHM O U NT
MALPL A Q UET F L USHM O U NTMALPL A Q UET F L USHM O U NT
MALPL A Q UET F L USHM O U NT
ASSEMBLY AND MOUNTING INSTRUCTIONS S G - 1 2 2 9
M O U N T I N G
M O U N T I N GM O U N T I N G
M O U N T I N G I N S T R U C T I O N S
I N S T R U C T I O N SI N S T R U C T I O N S
I N S T R U C T I O N S
STEP
STEP STEP
STEP 1
11
1
SHUT OFF THE MAIN ELECTRICAL SUPPLY TO THE JUNCTION
BOX FROM THE FUSE BOX/CIRCUIT BREAKER. TURNING POWER
OFF AT THE SWITCH IS NOT `SUFFICIENT.
STEP 2
STEP 2STEP 2
STEP 2
REMOVE THE THREE ACORN NUTS FROM THE FIXTURE AND
REMOVE THE ELECTRICAL ASSEMBLY FROM THE MOUNTING
ASSEMBLY.
STEP
STEP STEP
STEP 3
33
3
A) UNTHREAD THE JUNCTION BOX SCREWS 1/2” FROM THE
CEILING SURFACE. PUSH THE MOUNTING ASSEMBLY TO THE
CEILING ENSURING THAT THE JUNCTION BOX SCREWS PASS
THROUGH THE OVERSIZED HOLES IN THE MOUNTING PLATE.
B) ROTATE THE MOUNTING PLATE CLOCKWISE TO SLIDE THE
JUNCTION BOX SCREWS INTO THE SLOTS OF THE MOUNTING
PLATE. TIGHTEN THE JUNCTION BOX SCREWS TO SECURE THE
MOUNTING PLATE IN PLACE.
STEP
STEP STEP
STEP 4
44
4
USING THE WIRE NUTS PROVIDED, MAKE ELECTRICAL
CONNECTIONS FROM THE ELECTRICAL ASSEMBLY BY
FOLLOWING THE ELECTRICAL CONFIGURATION TABLE BELOW.
ENSURE ALL ELECTRICAL CONNECTIONS ARE WRAPPED WITH
UL-LISTED ELECTRICAL TAPE. IMPORTANT: NEVER ALLOW
ELECTRICAL ASSEMBLY TO “HANG” FROM ELECTRICAL
CONNECTIONS OR TO OTHERWISE PUT PRESSURE ON THE
CONNECTIONS.

MALPL A Q UET F L USHM O U NT
MALPL A Q UET F L USHM O U NTMALPL A Q UET F L USHM O U NT
MALPL A Q UET F L USHM O U NT
ASSEMBLY AND MOUNTING INSTRUCTIONS S G - 1 2 2 9
STEP
STEP STEP
STEP 5
55
5
SLIP THE ELECTRICAL ASSEMBLY OVER THE THREE SCREWS IN
THE MOUNTING ASSEMBLY AND SECURE IN PLACE USING THE
THREE ACORN NUTS PREVIOUSLY REMOVED.
STEP
STEP STEP
STEP
INSTALL THE LIGHT BULB IN FIXTURE SOCKET AND RESTORE
POWER TO THE CIRCUIT. CONFIRM PROPER OPERATION OF THE
LIGHT FIXTURE.
STEP
STEP STEP
STEP 7
77
7
CAREFULLY PLACE THE GLASS BOWL INTO THE CAGE
ASSEMBLY.
STEP
STEP STEP
STEP 8
88
8
FLIP UP THE LATCH HINGES ON THE MOUNTING ASSEMBLY. LIFT
UP THE CAGE ASSEMBLY UP TO THE MOUNTING ASSEMBLY
ALIGNING THE LATCH KNOBS WITH THE LATCH HINGES. FLIP THE
LATCH HINGES DOWN OVER THE LATCH KNOB. THEN TIGHTEN
THE LATCH KNOBS TO THE HORIZONTAL POSITION.

MALPL A Q UET F L USHM O U NT
MALPL A Q UET F L USHM O U NTMALPL A Q UET F L USHM O U NT
MALPL A Q UET F L USHM O U NT
ASSEMBLY AND MOUNTING INSTRUCTIONS S G - 1 2 2 9
E L E C T R I C A L C O N F I G U R A T I O N T A B L E
E L E C T R I C A L C O N F I G U R A T I O N T A B L EE L E C T R I C A L C O N F I G U R A T I O N T A B L E
E L E C T R I C A L C O N F I G U R A T I O N T A B L E
F R O M H O M E
F R O M H O M EF R O M H O M E
F R O M H O M E F R O M L U M I N A I R E
F R O M L U M I N A I R EF R O M L U M I N A I R E
F R O M L U M I N A I R E
GENERAL NOTE:
GENERAL NOTE:GENERAL NOTE:
GENERAL NOTE: USE UL LISTED WIRE NUTS FOR THE
WIRING CONNECTIONS IN THIS LUMINAIRE. WRAP WIRE
NUT CONNECTIONS WITH UL LISTED ELECTRICAL
TAPE.
FOR QUESTIONS, PLEASE CONTACT CLIENT SERVICES
AT: 843.723.8140 OR [e-mail]
CONNECT BLACK OR RED (HOT)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE ROUND/BLACK WIRE
(HOT)
CONNECT WHITE (NEUTRAL)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE RIBBED/WHITE WIRE
(NEUTRAL)
CONNECT GREEN INSULATED OR BARE COPPER (GROUND -) HOUSE
SUPPLY CIRCUIT WIRE AND LUMINAIRE BARE STRANDED WIRE
(GROUND -) TO GREEN GROUND SCREW ON CROSSBAR.