Urban THE O INITIATIVE OFOUNT Product manual

1
The O Fountain is 100% Australian made. The Glass Reinforced Concrete
sculpture is manufactured in regional Victoria (Gippsland), Australia.
Installation and Maintenance Guide
making life better.

2
Installation and Maintenance Guide
Dimensions
Height 1,395mm
Width 804mm
Weight 120 kg (TBC)
Material
Outer Shell 15mm Glass Reinforced Concrete (GRC)
MPa 21
Nozzle Stainless Steel
Push Buttons Stainless Steel
Drain Gate Glass Reinforced Concrete
Base Plate Stainless Steel
Mounting Frame Stainless Steel
Flow rate 12.6 litres p.minute
Power None
Operating temperature Ambient
Minimum operating temperature 1 degree C
Rated working pressure 600 kPa
Hosing
Internal 5/6”
Inlet connection 1/2” BSP
making life better.

3
Certication
Disability Accessible - Certied (DO-16-1958)
WaterMark (AS/NZ4020 - for detail visit http://bit.ly/WMK26130)
Service and Maintenance
The O fountain has been developed with support from Zip Water, therefore we
highly recommend to book a Zip Service Technician in the event the unit needs
repair and/or a part is ready for replacement.
Filter
• The lter needs replacement every 12 months or when more than 96,000 Litres has
been dispensed.
• The lter part number is 92323-ZGP65S
• We will send a reminder email or please contact the O initiative to book in a
lterreplacement service.
• The Zip Water Replacement Filter is $330 ex GST.
• A visit by a Zip Water Technician to install the replacement lter including a
Sanitation Service (making sure the lter is activated correctly) is: $99 standard call
out fee +$45 per 15 mins.
Parts that may need replacement over time:
ENWARE BUB260B ASSEMBLY, SPRING ACTION STUFFING BOX
This is the push button and may need replacement.
APEX VALVE - FiltaMate FM 600
This is the pressure limiting valve that is in the box with the isolation valve. The
manufacturer recommends replacing this item every 5 years.
Please note: The Enware Stung Box is pressure operated. When the lter is at
capacity (or when clogged up) the pressure will drop and the stung box will no
longer automatically close. It will look as if the fountain is leaking, however, it simply
means that the lter needs replacement.
Installation and Maintenance Guide
making life better.

4
WARRANTY
The warranty is a standard 12-month warranty on parts. Meaning that if any part
should fail within 12 months from the date of installation, except as detailed below,
that part will be repaired or replaced free of charge by the O Initiative, its Distributor
or Service Provider, provided that:
• The O fountain is installed and used strictly in accordance with the instructions
supplied; and
• Any failure is not due to accident, misuse, abuse, unsuitable water conditions,
use of non-authorised parts including non-authorised lters or to any alteration,
modication or repair by any party not expressly nominated by The O Initiative.
• No warranty applies to the service life of any water ltration cartridge installed,
as lter cartridge service life may vary according to water quality and the rate of
water consumption.
The standard warranty covers the cost of both parts and labour.
making life better.
Installation and Maintenance Guide

5
Mounting frame
Mounting plate
M12x40 CSK SOC Head
Anchoring
The O Fountain is delivered with the stainless steel mounting plate tted securely to
the reinforced concrete body. A matching stainless steel mounting frame is supplied
for xing onto a concrete slab at the point of installation.
Several options for installation are shown in p.10, p.11, p.12.
Each unit is supplied with an isolation valve that is connected to a pressure
reducing valve. (Ball Valve, Y-strainer, Pressure Limiting Valve)
making life better.
Installation and Maintenance Guide

6
Component Parts
1. Push Button
2. Outlet Manifold
3. Side Manifold
4. Casing Front
5. Casing Rear
6. Mounting Plate
7. Rag Bolts
8. Mounting Frame
9. Drain Cover
10. Access Door
11. Straight Adapter 5/16”
12. Stem Elbow
13. Equal Tee
14. Equal Elbow
15. Bulkhead Connector
16. Zip - Global Plus Filter
17. Poly Drain DN50
18. Waste Pipe DN50
19. Feeder Pipe
20. Cover Fixing Screw
21. Plate Screw
22. Door Fixing Screw
23. Mounting Bolt
making life better.
Installation and Maintenance Guide

7
Overall Dimensions
Detail A
making life better.
Installation and Maintenance Guide

8
Mounting Plate
making life better.
Installation and Maintenance Guide

9
Mounting Frame
making life better.
Installation and Maintenance Guide

10
Installation Option A
Paved Surface
Note: Ensure xing ring is set level.
making life better.
Installation and Maintenance Guide

11
Installation Option B
Concrete Slab – Existing Building
Note: Ensure xing ring is set level.
making life better.
Installation and Maintenance Guide

12
Installation Option C
Concrete Slab – New Build Parks and Gardens
Note: Ensure xing ring is set level.
making life better.
Installation and Maintenance Guide

13
Contact
07 3382 7372
oce@urban.com.au
5 Telford Circuit YATALA QLD 4207
making life better.
Installation and Maintenance Guide