urmet domus 1099/212 User manual

DS1099-077
Mod.
1099
WIFI 1080P IP PoE CAMERAS SERIES
BULLET
1099/212
USER MANUAL

2DS1099-077
CONTENTS
CONTENTS.............................................................................................................................................................2
INTRODUCTION.....................................................................................................................................................3
1PRODUCT DESCRIPTION............................................................................................................................3
1.1 Technical specifications...............................................................................................................3
1.2 Opening the package...................................................................................................................3
1.3 Warnings......................................................................................................................................4
2SIMPLIFIED EU DECLARATION OF CONFORMITY ..................................................................................5
3INSTALLATION.............................................................................................................................................5
3.1 1099/212 →WiFi Bullet Varifocal camera...................................................................................5
4HOW TO CONFIGURE THE CAMERA IN A NETWORK.............................................................................6
4.1 How to add the camera to a WiFi network from the App .............................................................6
4.2 Static IP address allocation..........................................................................................................6
5EASYTOOL ...................................................................................................................................................7
6ACTIVEX CONTROL CONFIGURATION .....................................................................................................8
7CONNECTION FROM OTHER WEB BROWSERS....................................................................................10
8IP CAMERA WEB PAGE CONFIGURATION.............................................................................................10
8.1 Live.............................................................................................................................................10
8.2 Playback.....................................................................................................................................11
8.3 Remote settings.........................................................................................................................12
8.3.1 Display............................................................................................................................................... 12
8.3.2 Network.............................................................................................................................................. 14
8.3.3 Alarm.................................................................................................................................................. 21
8.3.4 Record ............................................................................................................................................... 22
8.3.5 System............................................................................................................................................... 23
8.3.6 Advanced........................................................................................................................................... 28
8.3.7 4G settings......................................................................................................................................... 30
8.4 Local settings .............................................................................................................................31
8.5 Output ........................................................................................................................................31
9VIEWING FROM APP .................................................................................................................................32
10 CONFIGURATION OF OTHER DEVICES ..................................................................................................33
11 ROUTER 4G-WI-FI SETTINGS...................................................................................................................33
11.1.1 Device status ..................................................................................................................................... 34
11.1.2 System Settings................................................................................................................................. 35
11.1.3 Quick Settings.................................................................................................................................... 41
11.1.4 Modify Password................................................................................................................................ 41
11.1.5 STATISTICS ...................................................................................................................................... 42
11.1.6 CONNECTED DEVICES.................................................................................................................... 42
11.1.7 NETWORK Settings........................................................................................................................... 43
11.1.8 Wi-Fi Settings..................................................................................................................................... 45
12 TECHNICAL SPECIFICATIONS.................................................................................................................46
13 APPENDIX...................................................................................................................................................48
13.1 FAQ............................................................................................................................................48
ENGLISH

DS1099-0773
INTRODUCTION
Dear Customer,
Thank you for purchasing this product. We invite you to rear this manual carefully before starting any operation. The software
can be updated at any time. Consequently, the contents of this instruction manual are subject to change without prior notice.
Notes:
➢IPC standard for Internet Protocol Camera.
➢Select: left click.
➢Double click: left click twice.
➢Default IP address of the IP camera enabled in absence of DHCP: 192.168.100.100.
➢Default username of the camera IP: admin (lower case); Password: admin (lower case).
➢Default web port: 80. Default web port: 6066. Command port: 6060.
➢To avoid IP address conflicts, it is advisable to connect and configure one IP camera on the network at a time.
➢The content of this manual could be different from your current version. Please contact Urmet Technical Customer
Care if you encounter problems during operations. The manual will be regularly updated without prior notice.
1 PRODUCT DESCRIPTION
URMET devices Ref. 1099/212 is a wireless/LTE IP cameras which may be controlled entirely by connecting to the TCP/IP
network.
1.1 Technical specifications
➢High-performance CMOS sensor.
➢Optimised H.264/H.265 video compression algorithms; multi-stream transmission for high-definition images on
broadband and narrowband media.
➢Simultaneous connection
➢With integrated web server, Internet Explorer can be for real-time monitoring, setting and managing from the website.
➢Mobile software based on the following platforms: iOS (iPhone), Android (Smartphone).
➢Possibility to record on micro-SD card (not included) or on IP HVR/NVR device (not included).
➢Remote system updates supported.
➢LAN and Internet supported.
➢ONVIF protocol supported.
➢Various network protocols supported, such as HTTP, TCP/IP, IPv4, UPNP, RTSP, UDP, SMTP, NTP, DHCP, DNS,
DDNS.
➢LTE modem: band 1,2,3,5,7,8,20,34,38,39,40 e 41 with integrated antenna of 2dBi
➢Alarm function supported on movement detection (the user can set area and sensitivity).
➢Privacy area function supported.
➢Wireless connection function.
➢Snapshot function. Image uploading from email.
➢Automatic reset function supported. Can be connected automatically in case of network interruption.
Note: the specifications of the various products may be subject to minor changes.
1.2 Opening the package
Check that the packing and the contents are not visibly damaged. Contact the retailer immediately if parts are either missing
or damaged. Do not attempt to use the device in this case. Send the product back in its original packing if it is damaged.
ACCESSORIES PROVIDED
➢1 WIFI IP camera
➢1 Mini-CD with URMET software.
➢1 URMET quick guide on paper
➢1 URMET App V-Stream Quick Guide on paper
➢1 addendum containing warnings
➢2 Antennas
➢1 first installation kit containing fixing screws and/or hex wrench and/or tools for opening the device
➢2 hex wrenches
IMPORTANT NOTE:
Accessories may vary without prior notice.

4DS1099-077
1.3 WARNINGS
Power
➢Make sure that the rating plate data corresponds to the power specifications before connecting the device to the
mains.
➢Arrange a suitable circuit breaker and fuse upstream of the devices.
➢Disconnect power by means of the circuit breaker in the event of a failure and/or bad operation.
➢The power unit is provided with the device.
Safety precautions
➢Keep the device away from rain and humidity to prevent the risk of fire and electrocution. Do not introduce material
(solid or liquid) inside. If this should accidentally occur, disconnect the device from the mains and have it inspected
by qualified personnel.
➢Never open the device. In all cases, contact a qualified personnel or authorised service centre for repairs.
➢Keep the device away from children to prevent accidental damage.
➢Do not touch the device with wet hands to prevent electrical shock or mechanical damage.
➢Do not use the device if it should fall or the external casing is damaged. Risk of electrocution if the device is used in
such conditions. Contact the retailer or authorised installer.
Installation precautions
➢Avoid pointing the lens directly towards the sun or intense sources of light also when the camera is off. The subject
must not be backlit.
➢Do not point the camera towards reflecting objects or mirrors.
➢Some lighting systems (e.g. coloured fluorescent lights) may false the colours.
➢Do not arrange this device on an unstable surface, such as a tottering or slanted table. The device could fall causing
injury or mechanical failures.
➢Stop using the device if water or other material should penetrate inside: risk of fire and electrocution. Contact the
retailer or authorised installer.
➢Do not cover the device with a cloth while it is running to prevent deforming the external casing and overheating the
internal parts: risk of fire, electrocution and mechanical failure.
➢Keep magnets and magnetised objects away from the device to prevent faults.
➢Do not use the device in presence of smoke, vapour, humidity, dust or intense vibrations.
➢Wait for a while before operating a device immediately after transporting it from a cold place to a warm place and
vice versa. Wait on average for three hours: this will allow the device to adapt to the new ambient (temperature,
humidity, etc.).
Precautions
➢Make sure that the device is intact after removing it from the package.
➢Check that the working temperature is within the indicated range and that the environment is not excessively damp.
➢Do not point the camera towards the sun to prevent damaging the sensor.
Cleaning the device
➢Rub delicately with a dry cloth to remove dust and dirt.
➢Dip the cloth in neutral detergent if dirt cannot be removed with a dry cloth alone.
➢Do not use spray products to clean the device. Do not use volatile liquids (such a petrol, alcohol, solvents, etc.) or
chemically treated clothes to clean the device to prevent deformation, deterioration or scratches to the paint finish.
➢Disconnect the device from the mains before cleaning or maintenance.
Image recording
➢This device was mainly designed to transmit and possibly record images, not as a burglar alarm. Urmet S.p.A. cannot
be held liable for loss or damage following theft sustained by the user.
➢Test recording before using the device to make sure that is working correctly. Please note that Urmet S.p.A. is not
liable for loss of stored data consequent to loss or damage caused by incorrect installation, use, improper use or
malfunctioning of the device.
➢This device contains precision electronic components. Protect the device from shocks to ensure correct recording of
images.

DS1099-0775
Privacy and Copyright
➢The IP camera is a CCTV system device. Recording of imagines is subject to the laws in force in your country.
Recording of images protected by copyright is forbidden.
➢Product users shall be responsible for checking and respecting all local rules and regulations concerning monitoring
and recording video signals. The manufacturer SHALL NOT BE LIABLE for use of this product not in compliance with
the laws in force. For more information see http://www.garanteprivacy.it.
Firmware upgrades
➢Periodically check the URMET Customer Service Technical Area for firmware upgrades.
Network configuration
➢The camera is set to DHCP mode. If the network on which it is installed does not support dynamic addresses (DHCP),
the camera will automatically activate the default IP address 192.168.100.100. The “Easy Tool” Urmet software can
be used to change the default IP address and other network configurations of the camera to prevent conflicts with
other devices on the network. Always check the warnings for restrictions concerning the address which can be
assigned to the camera.
Network connections
➢When connecting a PC (using Software Client or Browser), any video channel on the PC will be using “unicast” connection
(TCP, RTP, UDP).
➢The device can support a limited number of “unicast” connections so it is possible to show the video on maximum 4 remote
devices (of which 2 smartphones at the most) at the same time depending on the available network band.
Reset button
The camera is equipped with two Reset buttons:
➢Button on the cable (press for at least 3 seconds): this can be used to reset all the factory settings of the IP
camera only (e.g. camera password, video stream, image settings, motion detection, recording, etc.). It
leaves the WiFi and 4G configurations unchanged.
➢Button adjacent to the nano-SIM slot: this can be used to restore all factory settings for the integrated 4G/WiFi router only.
It leaves the IP camera configurations unchanged.
2 SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, URMET S.p.A. declares that the radio equipment types: camera 1099/212, is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.urmet.com
3 INSTALLATION
3.1 1099/212 →WIFI BULLET VARIFOCAL CAMERA
It is advisable to proceed as follows for correct camera installation and configuration:
1. Make sure that the unit to be connected is not powered before starting the installation procedure. Fit each of the
two aerials (black aerial for 4G, white aerial for Wi-Fi) supplied on the respective camera connector.
2. Insert the nano-SIM (not included) into the appropriate slot of the camera with the device switched off (see next
image).
IMPORTANT: It is recommended to disable the SIM card PIN from your mobile phone or tablet before inserting
the SIM card into the camera. If necessary, refer to section 5 of this guide to disable the PIN of the SIM already
inserted in the camera.
IMPORTANT: Some mobile network operators can introduce major delays or blockages in camera connections.
3. When recording to a micro SD card (not included), insert the SD memory card into the SD memory card slot of
the camera when the power is off (see next picture). Format the SD card from camera settings on the web page
or from the app.
4. Place the camera in a location with good 4G signal reception and then power the camera (power supply not
supplied). Within a few minutes of switching on, the camera automatically connects in 4G to the internet
network.

6DS1099-077
5. To check the connection of the camera in 4G to the internet, connect a personal device such as a
smartphone/tablet/PC to the Wi-Fi network of the camera (Wi-Fi SSID): “MIFI_...”, Wi-Fi password:
1234567890) or connect a PC via cable to the network connector of the camera.
6. The integrated 4G/Wi-Fi router provides internet access to the camera and also to devices connected via Wi-Fi
or cable to the camera.
For remote viewing of the camera from a smartphone/tablet device, see section 4 of this guide.
To access the advanced configurations of the built-in 4G/Wi-Fi router of the camera, see section 5 of this guide.
4 HOW TO CONFIGURE THE CAMERA IN A NETWORK
In this section explanation is provided to configure the camera in the network and to connect it remotely from the smartphone
App or from a PC.
IMPORTANT NOTE: the camera is provided with two different network boards, one for the wire connection and one for the
WiFi connection, each with its own MAC address and is own IP address.
4.1 HOW TO ADD THE CAMERA TO A WIFI NETWORK FROM THE APP
The camera can be quickly configured on the WiFi network using a smartphone, to do so refer to the paper Quick Guide of
the Urmet App V-Stream provided with the product:
V-Stream
Alternatively, the camera can be also configured on the WiFi network without making use of the smartphone, i.e. using a PC
in either way: by temporarily wiring the camera to the LAN (see § 4.3) or in ACCESS POINT mode (see § 4.4).
4.2 STATIC IP ADDRESS ALLOCATION
The network parameters of the camera, such as IP address, subnet mask and gateway may be set and modified using
“EasyTool” provided or on the camera web page.
If the camera has to be recorded by a HVR/NVR device it is advisable to set a static IP address after having appropriately
connected and configured the camera in the network (see previous sections). Make sure that the IP address you want to
assign to the camera is not already used in the network. It is better to use an address outside the range of addresses assigned
by means of DHCP.
To assign the static IP address, select the camera after having detected it in “EasyTool”. As shown in the figure below, fill in
the static network parameter to be assigned (the fields are filled in automatically by selecting the correct network interface
from those available on the PC) in the specific section of the tool.

DS1099-0777
Press “Modify IP Address” to change the IP address of the device and wait for a few instants.
Press the “Refresh List” button of “EasyTool” to refresh the list and view the camera with the changes made.
IMPORTANT NOTE: to set/edit the network parameters of the camera (IP address, subnet mask, gateway) it is advisable to
use EasyTool or the web page of the camera. It is not advisable to set/edit the network configurations of the camera in the
NVR/HVR menus on which the camera was added; make sure that the NVR/HVR device is updated to the latest firmware
version.
5 EASYTOOL
The software can detect the IP address of the IP camera on the LAN. Firstly, unzip the easytool.zip file contained on the CD
included.
Install and run EasyTool.exe.
Start “Easy Tool” by selecting : the IP Address, Subnet Mask, Gateway and MAC Address will be
automatically shown for each IP camera, as shown in the following figure.
If the searched IP and the IP address of the PC are not on the same network segment, the IP address, the subnet mask and
other IP camera parameters can be changed by using Easy Tool.
Firstly, select the device the IP address of which you want to change and enter the new IP address, Subnet Mask and Gateway
values (Subnet Mask and Gateway may be inherited from the PC) and the username/password. Click on Modify IP Address
to change the IP address of the device.
IMPORTANT NOTE
The default IP address of the IP camera is “192.168.100.100”, the default username is “admin”, the default multimedia
port number is “6066” and the default command port is “6060”.

8DS1099-077
After having detected the IP camera, right-click and select “Open in IE” to open a Web page on IE. See the applicable section in the
complete manual if installation of an ActiveX component is required. You can select user name (default: admin), password (default:
admin), stream type (Main/Sub Stream) and language on the login page.
Select “Login” to open the LIVE page.
6 ACTIVEX CONTROL CONFIGURATION
You will need to install the plug-ins when inspecting the IP camera using Internet Explorer for the first time. Set the browse
protection level to install the plug-in. Select the menu [Tools/Internet Options/Security/Custom Level] and for "ActiveX controls
and plug-ins" select "Enable" or "Prompt", as shown in the following figure. For safety, reset the default protection setting in IE
after having viewed the IP camera image.

DS1099-0779
Plug-in installation method:
Enter the IP address of the IP camera on the IE address bar to inspect the IP camera. The controls will be loaded automatically
on the IP camera.
The plug-in installation window will appear. Click on "Install" to complete the installation automatically.

10 DS1099-077
7 CONNECTION FROM OTHER WEB BROWSERS
The camera web page can be accessed using a browser other than Internet Explorer, simply by keying in the IP address of
the camera on the navigation bar of the browser.
In this case, no additional components need to be installed and the displayed stream live consists in MJPEG video stream for
which selecting Main/Sub is not effective on the login home page.
IMPORTANT NOTE:
all the controls present on the lower bar of the live video (after login):
are available only if the Internet Explorer is used as browser after installing the ActiveX control of the camera on the PC.
These controls are not available when connecting to the web page of the camera using different browsers from IE.
8 IP CAMERA WEB PAGE CONFIGURATION
8.1 LIVE
Open Internet Explorer or other browser and enter the IP address of the IP camera (e.g.: http://192.168.100.100). The login
window appears. Observe the following figure:
The user can select the Stream Type on the access interface (this selection is only effective for Internet Explorer).
Enter User name (default: admin) and Password (default: admin), select Language and click on “Login” to access the Live
interface, as shown in the following figure.
Right-click (on Internet Explorer with ActiveX only) to select the stream to be displayed (Main Stream, Sub Stream) and to
view the bitrate.
Other Live interface buttons (on Internet Explorer with ActiveX only):

DS1099-07711
: this is used to search and playback the video files recorded in the camera’s SD memory card (not
included).
: This is used to access the device setup menu to set the various customised parameters;
: Snapshot, file type, saving path etc.;
: Close and go back to the login page;
: PTZ interface to control ZOOM and FOCUS (only for Autofocus camera models)
: Control button preview. From left to right,
the buttons are: Start/Stop live video, Switch On/Off the PC Mic (to send audio to the camera), Switch On/Off the PC Audio
(to receive audio from the camera), digital zoom, Start/Stop video recording on PC, Snapshot.
8.2 PLAYBACK
Click on to access the Playback interface:
Select one of the red dates within the selected month and push the button to display the video recorded files on
the time bar. Different colors refer to different recording Type (Normal, Manual, Alarm, Motion).
Use the button to start playing back the video.
To quickly position the playback time cursor on the time bar during the playback you can use the function:
and push Go while the video is playing.

12 DS1099-077
8.3 REMOTE SETTINGS
8.3.1 DISPLAY
1) OSD CONFIG
Click on (Remote settings) to access the Live interface OSD Config (default).
➢Name: IP camera name.
➢Channel Display: Enable/Disable. The display position can be customised.
➢Time Display: Enable/Disable. The display position can be customised.
➢Flicker Control: 50Hz/60Hz/Close
2) IMAGE CONTROL
Click on 【Display】→【Image Control】to access the following interface.
➢IRCUT Mode: 5 modes:
oGPIO Mode or Passive Mode : default mode. The camera switches from colors to black and white (turning on
the IR LEDs) and vice versa based on the environment light detected by the external sensor integrated in the
camera.

DS1099-07713
oColor Mode or Daytime: fixed setting as colors only, it never switches to B/W picture.
oBlack & White Mode or Night: fixed setting as B/W only, it never switches to color picture.
oVideo Mode or Active Mode: the camera switches from colors to black and white (turning on the IR LEDs) and
vice versa based on the brightness level detected by the video sensor.
oTime Mode or Timing: the camera switches from colors to black and white (turning on the IR LEDs) and vice
versa based on the set time schedule
➢IR-CUT Delay: This is the IRcut delay time.
➢IR-CUT Reverse: Enable/Disable the inversion of the functionality
➢Image setting: This is used to adjust brightness, contrast saturation, hue, sharpness.
➢BLC (Back light compensation): This is used to Enable/Disable backlight compensation. This function can
compensate the shadows on the subject in case of exposure against sunlight. In some scenarios of use, the visual
field may contain a very bright background, such as a door or a window in full sunlight, with the observed subject
surrounded by the light field. In this case, the picture may appear dark and flat. Backlighting compensation may be
used to solve this problem.
➢3D Noise Reduction: Auto/Week/Normal/Strong
➢WDR: This enables or disables the WDR function: Weak, Normal, Strong.
WDR allows the camera to acquire highly contrasted images. In short, DR (dynamic range) shows the details of the
light part and the dark part of the image. A broader dynamic range shows richer layers and a vaster colour range.
➢Flip: 4 modes: Close, Leftright, Updown, Center.
➢White Balance: Auto, Manual, Incandescent, Warm, Fluorescent, Natural.
Manual: Manual gain adjustment of red and blue colours for the camera video.
Auto: Optimisation according to the current lighting conditions and method of the screen and video colour calibration
of the camera video colours.
➢Iris Type: Manual and automatic modes can be selected. The default mode is Auto.
➢Time exposure: Camera exposure level adjustment.
➢Gain: Automatic gain level AGC adjustment (Auto, 6dB, 12dB, 18dB, 24dB, 30dB, 36dB, 42dB).
3) PRIVACY ZONE
Click on 【Display】→【Privacy Zone】to access the following interface.
Privacy zone setting:
1. Click to enable the privacy zone.
2. Select the Privacy area to be activated from the available four (Window 1, Window 2, Window 3, Window 4).

14 DS1099-077
3. Point to the corner in the bottom right of each Privacy area and drag the mouse to change the size. Then positionthe Privacy
area on the concerned area of the image.
4. Click on Save to activate the privacy area.
8.3.2 NETWORK
1) Network configuration
Click on 【Network】→【Network Setting】to access the following network page.
This page can be used to display and set the parameters related to the LAN of the camera:
➢Type: DHCP, Static or PPoE. The default setting is Static.
➢Command Port: This is the command port of the IP camera. Default: 6060
➢HTTP Port: This is the web port of the IP camera. Defalut: 80
➢IP address: Camera IP address
➢Subnet Mask: Subnet mask of the IP camera.
➢Gateway: IP address of the gateway used to access the Internet
➢DNS1/DNS2: IP addresses of the DNS servers.
➢Media Port: This is the client port of the IP camera. Default: 6066
➢MAC address: This is the MAC address of the LAN board of the camera.
Only in the case that the camera has to be recorded by a network device HVR/NVR, it is advisable to set a static IP address
after having appropriately connected and configured the camera in the network. Make sure that the IP address you want to
assign to the camera is not already used in the network. It is better to use an address outside the range of addresses assigned
by means of DHCP.
Select “Type = Static” and fill in the following fields: IP address, Subnet mask, Gateway and DNS. Press Save to save the
changes.
2) Video Stream
Click on 【Network】→【Video Streaming】to access the following interface.

DS1099-07715
➢Type: MainStream, SubStream.
➢The user can set: Resolution, FPS, Audio (if the camera model has audio input), Bitrate control: CBR/VBR and the
MainStream/SubStream Bitrate value.
➢Resolution: MainStream 1080P(1920x1080), 960P(1280x960), 720P (1280×720), SubStream (704×576, 640×360,
352×288).
➢FPS: max 20 for the Mainstream and 25 for the Substream
➢Audio: enable/disable TLC audio input (if supported by the camera model).
➢Rate Control: Set the Bitrate management as CBR (Constant Bit Rate) or VBR (Variable Bit Rate, at 6 quality levels
from Best to Worst.
➢Bitrate: set the transmission speed to bits per second as manual (user-defined) or default value.
IMPORTANT NOTE:
It is possible to access the third stream of the camera which is a MJPEG stream, by inputting the following URL in any internet
browser’s navigation bar:
http://IP/Streams/1/4/ReceiveData
Description:
•IP: to be replaced with the actual IP address of the device
•The MJPEG stream resolution can be modified in the following section: 【Advanced】→【Snapshot Settings
】
IMPORTANT NOTE:
The HTPP URL to get single JPEG snapshots is the following:
http://IP/Snapshot/1/RemoteImageCapture?ImageFormat=2

16 DS1099-077
Description:
•IP: to be replaced with the actual IP address of the device
•The JPEG snapshot resolutioncan be modified in the followingsection: 【Advanced】→【Snapshot Settings
】
3) FTP
Click on 【Network】) →【Email】to access the following interface.
Server: it supports IP address or domain string
4) Email
Click on 【Network】) →【Email】to access the following interface

DS1099-07717
Email service setting. By using this function in association with the Motion alarm function, the camera can sent the images
acquired by email on the Internet by contacting the set email server (SMTP).
Email: Disable/Enable.
SMTP Port: The default value is 25 (email service port). If
SSL is enabled, the port is usually 465.
SSL: Disable/Enable.
Authentication: Disable/Enable.
SMTP Server: Enter the email server address.
Sender Email: The sender’s email address.
Sender Pwd: The sender’s email password.
Receiver Email: The recipient's email address (three
addresses are possible).
Snap Interval: This is the email sending
frequency in case of event.
Test Email: This sends a email to test that parameter are
correct.
5) DDNS
Click on 【Network】) →【DDNS】to access the following interface.
DDNS: This refers to the Dynamic Domain Name Server, which can be used to reach the camera via the Internet in
case of connection using a dynamic public IP address.

18 DS1099-077
Connection Status is used to check the settings of the DDNS account.
6) UPNP
Click on 【Network】) →【UPNP】to access the following interface.
UPnP: This refers to Universal Plug And Play, which is a network protocol which allows various terminals to connect to
each other without needing to open ports on the connection devices. The port association can be selected: http, RTSP,
Command and Media.
Check that the UPnP function is enabled also on router.
DDNS: Disable/Enable.
Server: Select the DDNS provider.
Host Name: Enter the name of the host recorded
on the DDNS provider website.
User Name: Enter the name of your account recorded on
the DDNS provider website.
Password: The user's password.
Update Time: frequency with which the camera refreshes
information on the DDNS server.

DS1099-07719
7) RTSP
Click on 【Network】) →【RTSP】to access the following interface.
➢RTSP Port: The default password is 554. The device will be restarted after the change.

20 DS1099-077
Description
•rtsp://IP:Port/live/A/B
•IP: IP address of the device.
•Port: RTSP port of the device. Default: 554.
•A: 0, 1, 2 ... channel ID number (for camera type devices use any ID, e.g. 0).
•B: MAIN refers to “main stream”, SUB refers to “sub stream”.
8) P2P
Click on 【Network】) →【P2P】to access the following page.
P2P refers to the functionality that makes the device available for connections from remote software and app through
the Internet, without any port-forwarding/virtual server setting in the router.
Description
•P2P: enable/disable the function. Default: enabled
•UUID: this is the ID code that indefies univocally the devices and that has to be input in the software/app to open the
connection to the camera. It is also available on the device as a QR code label.
•Status: “internet ready” means that the device can connect to the internet through the router, so it is available to
accept connections from software/app installed on remote PC/smartphone.