US Steam Sea Hawk User manual

!
Sea Hawk
User Manual
US Steam
7940 Rodeo Trail
Suite 360
Mansfield, Texas 76063

"
Table of Contents
Components ______________________________________________________
4
Steam
and Vacuum Controls __________________________________________ 5
Quick
Start _______________________________________________________ 6
Shut Down _____________________________________________________
8
Trouble Shooting
___________________________________________________ 9
Tools
& Accessories _______________________________________________
10
Maintenance
_____________________________________________________
12
Descaling ________________________________________________________
15
Notices __________________________________________________________
16
Warranty & Repair _________________________________________________
17
Congratulations on your purchase of the US Steam Sea Hawk system.
The Sea Hawk not only combines a steam, extraction, and vacuum
cleaner into one system, but it included our patented RAIN SYSTEM™.
The RAIN SYSTEM™ is a sophisticated air filtration system using a
highly efficient nebulization filter and trap large dust particles in water.
Air is then passed through a 2nd HEPA filter system trapping even the
smallest of particles. THE AIR RELEASED FROM THE SEA HAWK
IS THEREFORE PURIFIED FROM ALL DIRT PARTICLES.

Vacu um Spe e d
Control
Steam Pressure
Control
Extraction Bottle
Connector
Carry Handle
Removable Lid
#
Components
Steam Reservior
Tank
Extraction
BottleVa c u u m
Collection Tank
ON/OFF
HEPA Filter
Technical Data:
Steam Pressure: 4.5 Bars
Air flow: 22 liters/second
Boiler Volume: .81 Liters
Boiler Capacity: .4 Liters
Recovery Tank Volume: 1.2
Liters

$
Vacuum & Ste am C on tr ol s
Vacuum Controls
Max Speed
Medium
Vac uu m
ON/OFF
Low
ØThe wet/dry vacuum can be
used independently or with the
steam and extraction.
ØUtilize the vacuum to reduce
surface moisture while
cleaning.
ØMax Speed can only be used
when using the vacuum
independently without steam or
extraction.
Steam Pressure Control
Steam Controls
Increase Decrease
Low Water
Steam Light
(soliid when ready)
Vac uu m Co ll ec ti on
Tank is FULL
Stand by Mode
Power
ON/OFF
ØMost cleaning jobs can be
performed on low or medium
steam setting.
ØThe Orange steam light will
blink during operation
indicating the water is heating
in the boiler.
ØIt will take 10 minutes for the
water to heat in the boiler and
the be ready for use.

%
Quick Start
1) ADD WATER
&Extraction Bottle
ØFill bottle completely and attached to the Sea Hawk.
'Steam Reservior Tank
ØRemove the cap on the steam reservoir and pour .8 Liters of
tap water and replace cap.
(Vac uu m Co ll ec ti on Ta nk :
ØAdd .7 liters of water.
ØFill only to mark on the tank separators.
)Reassemble Tank Lid and Tighten
ØInsert the vacuum hose with the release button on the
left side and the power command plug on top.
ØLift the silver hinge cover on the front of the Sea
Hawk and insert the power command connector.
ØGo to the Tool Application guide and select cleaning
attachment.
2) ATTACH HOSE & ATTACHMENT
3) PLUG INTO ELECTRICAL OUTLET
ØPlug the power cord and you will hear a beep and the green light will start
blinking.
ØThe Sea Hawk should be the only appliance plugged into the power outlet.
ØUse only a 12 gauge / 15AMP rated or higher extension cord.
ØIt will take 10 minutes for the Sea Hawk to heat and be ready for use.
4) ON/OFF
ØPush down on the power button and the Orange light will
start flashing signaling the boiler is heating.
ØOnce the boiler reaches pressure, the Orange will go solid
and the Sea Hawk is ready.
ØIf the Red “Low Water” light comes on and steamer starts
beeping, turn off your Sea Hawk and refill the steam fill
tank. Push power button to restart your Sea Hawk and
resume heating.
ØThe Orange light may blink during operation indicating the
boiler is heating.
ON/OFF
Add essential or balsamic oils to the water ONLY in
the vacuum collection tank.

*
Quick Start
6) BLEED THE HOSE
ØPull the trigger on the hose handle for 10 seconds to BLEED excess water from
the system.
ØWhen only steam is released from the hose, your system is ready to use.
7) STEAM CONTROL DIAL controls the amount of steam released.
ØIncrease Steam Pressure by Turning the dial counter-clockwise toward the (+)
sign on the dial.
ØDecrease steam pressure by turning the dial clockwise toward the (-) sign on
the dial.
ØTurning the dial all the way clockwise is the lowest possible setting and no
steam will come out when you press the steam trigger.
8) VA C U U M
ØPress the vacuum power button on the hose
handle to turn on the vacuum. The vacuum will
start on the “LOW” setting. To turn the vacuum
“off” push the same button again.
ØTo increase or decrease suction, push and
HOLD” the vacuum power button on the handle
ØTo vacuum liquids, do not fill the collection tank
with water. The Sea Hawk can aspirate up to 1.4
liters of liquid before needing to empty the tank.
The vacuum can only be used
on low or medium setting
while using the steam or
extraction function.
9) EXTRACTION
ØWhen activated, the extraction feature shoots hot water along
with steam for deep cleaning.
ØExtraction is activated on the hose handle by pushing the
button on the hose handle.
ØThe light on the handle will be ON indicating the Sea Hawk
is in Extraction mode.
ØUse the small or large extraction brush for cleaning.
10) REFILLING
ØWhen your Sea Hawk needs refilling, the Red low water light comes on and
steamer starts beeping.
ØTurn off the Sea Hawk and refill the steam reservior tank. Push power button
to restart your Sea Hawk and resume heating.

+
Shut Down
&Push ON/OFF button on Sea Hawk.
'Clean vacuum collection Tank
Remove the collection tank and drain contents from the vacuum reservoir and
steam reservoir tank. Clean the tank and remove the yellow nebulizers for
additional cleaning. Rise with hot water until all residue and stains on the tank
wall have been removed.
(Empty extraction bottle.
,Clean the exterior of the SteamVac with wet cloth. Do not use solvents or
detergents that could damage the plastic surface.
)Use hot soapy and water to clean brushes and nozzles.
If you have been cleaning a dirty or greasy surface, it is recommended that you clean
the vacuum hose before shutting down.
ØClean vacuum hose by activating the vacuum mode and suck water through the
hose.

-
Trouble Shooting
!"#$%&' (#%)*+#,
./ 0/123
Ø45267286981:6;5/<=>[email protected]=E8FG26D=<HH2>6EF@/6@526
2=2G@3EG8=6/<@=2@I
ØJ52G:6@526K<;26?/L6K/36@3EDD2>6GE3G<E@ ?328:23I
ØMK6<;EFH68F62L@2F;E/F6G/3>6E@6N<;@6N22@6@526K/==/1EFH632O<E32N2F@;P
ØQEFEN<N !"6H8<H266R6!%SQ0
Ø%T6K@I6N8L6=2FH@5
./6;@28N6G/NEFH6/<@6/K65/;26
ØM;6@526H322F68@@8G5N2F@6EF>EG@/36=EH5@6/FU66
ØV2G52G:6@5265/;268F>6D/1236G/NN8F>6G/FF2G@E/F6@/6N8:26;<326E@6E;6
G/332G@=W6G/FF2G@2>6@/6@5267286981:I
ØM;6@52618@236EF6@526?/E=236528@2>68F>6@526/38FH26EF>EG8@/36=EH5@6H/F26
;/=E>U
ØM;6@526;@28N6G/F@3/=68>X<;@N2F@6:F/?6@<3F2>6@/6@526G=/;2>6D/;E@E/FU
Y8@236G/NEFH6/<@6/K65/;2615E=26
@526<FE@6E;6528@EFH6<DI6
ØQ8:26;<326@5267@28N6Z<@@/F68F>65/;2658F>=26?<@@/F;68326EF6@526A[[6
D/;E@E/FI6
./632;D/F;26K3/N6?<@@/F;6/F6
5/;2658F>=2
ØJ52G:65/;26G/FF2G@E/F;I66
Ø43W6>E;G/FF2G@EFH6@5265/;268F>632G/FF2G@EFHI6
\<3EFH6@526183N]<D6D58;2 @526
728 981:^;68=83N6H/2;6/KKI
Ø452 ?/E=236D<==2>68==6@52618@236K3/N6@526;@28N632;23_/E36@8F:I
ØV2KE==6@526;@28N632;23_/E36@8F:I
Ø0<;[e-mail][6?<@@/F6/F6@526G/F;/=2 @/632;2@I
`8G<<N60/1236E;6EF;<KKEGE2F@
ØaND@W68F>632D=8G2618@236EF6_8G<<N6G/==2G@E/F6@8F:I
ØJ52G:6@5269a00S6KE=@2368F>6G=28F6EK6F2G2;;83WI
ØJ52G:6@5265/;268F>68GG2;;/3W6G/FF2G@E/F;I
Ø4526;28=683/<F>6@52618@236@8F:6E;6F/@6D/;E@E/F2>6G/332G@=WI
ØJ52G:6@5265/;268F>68GG2;;/3E2;6K/36D83@EG=26?=/G:8H2I
45265/;26/368GG2;;/3E2;658_268F6
<FD=28;8F@6/>/3I Ø\E3@658;68GG<N<=8@2>6EF6@5265/;26/36KE=@23I66J=28F6?/@568F>632EF;23@I6

Brush Nozzle
Part #
Rubber Insert
Part #
Carpet Insert
Part #
Carpets and rugs
Hard floors (wood, tile)
Rectangular Brush
Part #
!
Nylon Brush
Part #
Triangle Brush
Part #
Suction Nozzle
Part #
______________________________________________________
9
Accessories
______________________________________________________
Jett Nozzle
Part #
Hose Handle
Part #
Extraction Bottle
Part #
aL@2F;E/F6Y8F>;
083@6b6

NO ATTACHMENT Carpet, Upholstery, and mattress
Glass, windows, and mirrors
All hardwood surfaces
Pre-Cleaning in heavy soiled
area
Rubber tip with brush
Part #
Rubber tip
Part #
Nylon Brush
Part #
Carpet, Upholstery, and mattress
NO ATTACHMENT
Rubber tip with brush
Part #
Glass, windows, and mirrors
All Hard surfaces, tile, and
wood
Small Extraction Nozzle
Part #
Large Extraction Nozzle
Part #
Rubber Insert
Part #
10
Extraction Accessories
_____________________________________________________

!!
Maintenance
AFTER EACH USE
&Use hot soapy and water to clean brushes and nozzles.
'Clean vacuum hose by activating the vacuum mode and suck water through the
hose.
(Clean the exterior of the Sea Hawk with wet cloth. Do not use solvents or
detergents that could damage the plastic surface.
,Clean Vacuum Collection Tank
Remove the tank and drain water from the vacuum and reservoir and tanks.
Clean the tank and remove the yellow nebulizers for additional cleaning. Rise
with hot water until all residue and stains on the tank wall have been removed.
WA R N I N G : The yellow nebulizers may be removed for cleaning but must be
reassembled correctly before using. Using the SteamVac without nebulizer filters
could lead the serious damage.
MONTHLY
&De-Scale the boiler (see page 15)
'Clean the HEPA filter
(Check and clean the motor filter as needed.
TO CLEAN: Remove the grill from the back of the
Sea Hawk and remove the HEPA filter. Inspect the
filter for dirt and traces of dust. If there are traces
of dust, shake and brush it gently to remove all
visible particles. Replace the filter and reassemble
the cover.
ØUse small pliers or tweezers to remove.
ØWash with cold water and detergent.
ØLet it dry completely before replacing.

!"
Maintenance
YEARLY
-Replace the HEPA Filter
'Replace the O-Rings on hose handle and extension wands.
31
Look foward to it.
Pos.(3)
Entkalkungsanleitung B
Care of accessories
It is essential to clean accessory parts after use to maintain the performance and functionality of the
appliance. Te connections on the extension pipes and the safety handle can be sprayed with a
suitable lubricant or silicone spray as required. This will make it easier to change accessory parts.
Checking the O-rings
To avoid damage to the appliance or accessories, the O-rings on the safety handle and the extension
pipes must be checked regularly for damage. The O-rings will last longer if they are coated regularly
with a lubricant/ silicone spray or a non-acidic grease.
Checking the O-rings
Check the O-rings on the safety handle for damage:
Pos.(1): 1 O-ring on the suction pipe
Pos.(2): 2 O-rings on the steam spout
Check the O-rings on the connector for damage:
Pos(3): 2 O-rings on the brass spout
Checking O-rings on the extension pipes
Check the O-rings on all extension pipes for damage:
Pos.(4): 1: O-ring on the suction pipe
Pos.(5): 2 O-rings on the steam spout
Cleaning, care and maintenance of accessories
Pos.(1) Pos.(2)
Pos.(4) Pos.(5)
You can order a suitable set of O-rings from our online shop at
www.beam.de or by telephone on [phone].
Item no.: 96300
31
Look foward to it.
Pos.(3)
Entkalkungsanleitung B
Care of accessories
It is essential to clean accessory parts after use to maintain the performance and functionality of the
appliance. Te connections on the extension pipes and the safety handle can be sprayed with a
suitable lubricant or silicone spray as required. This will make it easier to change accessory parts.
Checking the O-rings
To avoid damage to the appliance or accessories, the O-rings on the safety handle and the extension
pipes must be checked regularly for damage. The O-rings will last longer if they are coated regularly
with a lubricant/ silicone spray or a non-acidic grease.
Checking the O-rings
Check the O-rings on the safety handle for damage:
Pos.(1): 1 O-ring on the suction pipe
Pos.(2): 2 O-rings on the steam spout
Check the O-rings on the connector for damage:
Pos(3): 2 O-rings on the brass spout
Checking O-rings on the extension pipes
Check the O-rings on all extension pipes for damage:
Pos.(4): 1: O-ring on the suction pipe
Pos.(5): 2 O-rings on the steam spout
Cleaning, care and maintenance of accessories
Pos.(1) Pos.(2)
Pos.(4) Pos.(5)
You can order a suitable set of O-rings from our online shop at
www.beam.de or by telephone on [phone].
Item no.: 96300
Hose Handle Extension Wands
(Check and clean the secondary motor filter found on
the bottom of the Sea Hawk.
ØTurn the locking knob on the filter cover.
ØRemove black filter and wash with cold water and
detergent
ØLet it dry completely before replacing.

!#
De-Scaling
DESCALING THE BOILER AND ELECTRONIC SENSOR
ØONCE PER YEAR
To extend the life of your Sea Hawk, we recommend descaling the boiler and the
electronic sensor. After prolong periods of activity, lime scale deposits make the
boilers of most steam appliances unusable. Your Sea Hawk comes with an exclusive
technology allows you to clean and inspect the electronic sensors that monitor the
boiler water levels.
IMPORTANT: The first time the Sea Hawk is used following the
descaling, remember to discharge steam into a cloth to catch the
descaling product. Once the discharged steam is clear, the Sea
Hawk is ready for use
How to De-Scale:
&Unplug the Sea Hawk
ØThe boiler should be cooled to room temperature before
starting
&Remove the vacuum collection tank and empty completely.
'Turn the steamer upside down, identifying the RED boiler
cap.
ØSlowly unscrew the Red boiler cap by turning the
counter-clockwise and remove.
,Pour de-scaling solution consisting of 2 cups of vinegar and 2 cups of water into
the boiler and replace the cap by turning clockwise until tight.
)Return the tank to original position, replace the tank, close the lid and tighten.
cTurn on the Sea Hawk ON for approximately 1 minute then turn off.
dLeave de-scaling solution in the boiler for 30 minutes
eEmpty the de-scaling solution from the boiler by turning over the Sea Hawk and
removing cap.
ØClean the sensor on the boiler cap with a scouring pad removing any
encrusted deposits.
fFill steam reservoir tank with water and turn ON the Sea Hawk allowing the
boiler to fill completely. It should take about 1 minute to fill the boiler.
gAfter 1 minute, turn over Sea Hawk and drain boiler completely. The Sea Hawk
is ready for use.

!$
Notices
Read all instructions before using this steam cleaner.
WAR N IN G : S TEA M G E N ER AT E D B Y TH E B LU E E VO L UT I ON IS E XTR E M LY HO T
AND WILL CAUSE INJURY IF IT COMES IN CONTACT WITH THE SKIN OR EYES.
USE AS DIRECTED BY THE MANUAL AND ONLY AIM THE STEAM HANDLE AT THE
CLEANING AREA.
WAR N IN G S
ØDO NOT leave the steam cleaner unattended while plugged in. Turn off all controls and unplug
the electrical cord when not in use, when moving to another location and before servicing.
ØDO NOT use with a damaged cord or plug. If the steam cleaner is not working as it should, has
been dropped, damaged, left outdoors or dropped into water, call for service before using.
ØNEVER attempt to disassemble this product in a way not instructed in this manual.
ØDO NOT handle the electrical plug with wet hands.
ØDO NOT use near children.
ØDO NOT pull or carry by cord. Keep cord away from heated surfaces.
ØKeep body, hands, and feet away from nozzle or brush steam. Steam can cause burns.
ØALWAYS set safety switch on hose handle into the locked position when not in use.
ØNot setting safety switch to locked position could result in an injury.
ØALWAYS test a small area before cleaning a large area on any type of surface to make sure no
damage will occur.
ØDO NOT expose machine to freezing temperatures while not in use.
ØDO NOT store gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
ELECTRICAL CONNECTIONS
The steam cleaner uses 110 Volts and will pull 13.1 Amps. It should be the only appliance plugged
into an outlet.
ØUse only a 12 gauge / 15AMP rated or higher extension cord.
ØAny alteration of electrical cord supply on this steam cleaner will void all warranties.
ØOnce electrical hook-up meets requirements, make sure all switches on front of unit are in the off
position before plugging unit into electrical outlet. For circuit breaker protection, if possible plug
the unit into an outlet isolated from other equipment, or turn the other equipment off while using
the steam cleaner —the combined electrical amperage of other equipment and the steam cleaner
together may cause a circuit breaker to trip.
ØAlways press the power button to OFF before you unplug the unit.
ØRemoving the ground prongs from the power cord will void any and all warranties and can cause
risk of shock or injury
KEEP FOR YOUR RECORDS. THIS MANUAL MUST BE RETAINED FOR FUTURE
REFERENCE. PLEASE READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND
WAR N IN G S CONTAIN E D IN TH IS M A NUA L BE F O RE US ING T H IS VA P O R S TE A M
CLEANER.
In order to reduce the risk of fire, electric shock, personal injury or damage to property, follow these
instructions carefully. When using electrical appliances, basic safety precautions should be followed.

!%
Warranty
Your steamer comes with aone year limited warranty which becomes effective on the date of shipment from
US Steam and is granted to the initial customer and is nontransferable.Any claims under this warranty must be
made before the end of the applicable warranty period.During such period if US Steam determines that apart
or system is defective in material or workmanship, US Steam, at its option, will provide you with arepaired
part or replace any part that is covered by the limited warranty.US Steam reserves the right to substitute
functionally equivalent new or serviceable reconditioned parts or systems.US Steam’s responsibility is limited
to repair, replacement, credit or refund, any of which may be selected by US Steam at its sole discretion.The
Warranty does not cover defects or damage arising from the disassembly or attempted disassembly of your
steamer.
The limited warranty covers only defects arising from normal use and does not include malfunctions or failures
arising from:misuse, abuse, neglect, alteration, usage not in accordance with user manual and instructions,
depletion of consumables, acts of nature or damage caused by repairs where such repairs were made without
US Steam’s express approval.
Use of any replacement parts other than authorized US Steam parts voids all warranties and can cause bodily
injury to the operator and damage equipment.Service performed by anyone other than factory authorized
personnel will void warranty.
SERVICE AND SUPPORT
Before you ship your steam cleaner for service, you must call [phone] (M-F 9am-4:30pm Central Time)
or contact us through the web at www.ussteam.net our customer service representative will explain how you
must package and ship your Steamer to prevent further damage
RETURN PROCEDURES
Prior to returning the product(s) you must obtain aReturn Merchandise Authorization (RMA) by calling (800)
613-3874.No returns will be accepted without RMA #. When packing the Steamer, you must use the
original packing material to prevent damage in shipping.Make sure you include all items and accessories.You
will be responsible for all shipping cost.Send returns to
US Steam
7940 Rodeo Trail, Ste 360
Mansfield, TX 76063
LIMITATIONS
EXCEPT AS SET FORTH HEREIN, US STEAM MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, AND DISCLAIM AND NEGATE ALL OTHER WARRANTIES, INCLUDING WITHOUT
LIMITATIONS, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR THE
PARTICULAR PURPOSE AND CONFORMITY TO MODELS OR SAMPLES.SOME JURISDICTIONS
DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES, SO THESE LIMITATIONS MAY NOT
APPLY TO YOU.
GOVERNING LAW, JURISDICTION AND COSTS
THESE LIMITED WARRANTIES ARE INCORPORATED INTO AND ARE ESSENTIAL AND
MATERIAL PROVISIONS OF THE TERMS AND CONDITIONS OF SALE OR SELLER PRODUCTS TO
YOU.ALL DISPUTES ARISING OUT OF OR RELATED TO THE LIMITED WARRANTY SET FORTH
HEREIN (CUSTOMER DISPUTES) SHALL BE GOVERNED BY THE LAWS OF THE STATE OF
TEXAS.THE CUSTOMER HEREBY CONSENTS TO THE JURISDICTION AND VENUE OF THE
STATE COURTS OF TEXAS TO RESOLVE ANY AND ALL CUSTOMERS DISPUTES WITH BOSTON
GREEN GOODS, INC., AND THE CUSTOMER WAIVES ALL DEFENSES TO SUCH JURISDICITON
AND VENUE INCLUDING, BUT NOT LIMITED TO, ANY DEFENSE BASED ON INCONVENIENT
FORUM.IN THE EVENT THE CUSTOMER AND BOSTON GREEN GOODS, INC.ARE UNABLE TO
RESOLVE ANY CUSTOMER DISPUTE, AND ANY COLLECTION ACTION, SUIT OR OTHER
JUDICIAL PROCEEDING IS COMMENCED;THE PREVAILING PARTY IN ANY SUCH ACTION,
SUIT OR PROCEEDING SHALL BE ENTITLED TO RECOVER ITS COSTS AND REASONABLE
ATTORNEY’S FEES INCURRED.

"./0123140
56/78019
Floors, Kitchen, Grills, & Bathrooms
The Blue Evolution will clean every area of your restaurant without chemicals.
Patient Beds, Wheel Chairs, & Curtains
Steam is a proven killer of virus and infection causing germs. UV-C
reduces airborne bacteria.
Deli’s, Freezers & Butcher
Chemical free cleaning in areas of food storage and preparation.
Desk, Tables, & Partitions
Blue Evolution guarantees a clean, germ-free work environment increasing
productivity and reducing sick days.
Lockers, Mats, & Gym Equipment
Steam kills mold and germs caused by sweaty athletes.
Equipment, Lockers, and Saunas
Kills viruses and germs found on workout equipment and gym floors.
Toys, Playgrounds, & Be ds
The Blue Evolution can clean all areas where kids pass germs. Extreme
cleaning can reduce sick days for kids and employees.
Seats and Floors
The Blue Evolution combines steam and extraction into one system for more
efficient detailing.
A Better Way to Clean
:36;.3<
#==8;.
(;>669
:<?
@1<AB13.
C206?608D.
7940 Rodeo Trail, Ste 360
Mansfield, Texas 76063
[phone]