USA Measurements Army iCount US-iC Series User manual

1
Electronic Counting
Scale Manual

2
Contents
【
1
】
ATTENTION..........................................................3
1.1 CONVENTIONAL ATTENTION
1.2 ATTENTION BEFORE USING
【
2
】
INSTALLATION……………………………………4
2.1 BODY INSTALLATION
2.2 BATTERY REPLACEMENT
【
3
】
INSTRUCTION………………………………………5
3.1 PARAMETERS
3.2 POWER SUPPLY
【
4
】
DISPLAY…………………………………………….6
4.1 PANEL DESCRIPTION
4.2 KEY DESCRIPTION
4.3 DISPLAY DESCRIPTION
【
5
】
OPERATION……………………………………..…9
【
6
】
FUNCTION SETTING…………………………….20
【
7
】
RS232 OUTPUT FORMAT……………………….25
【
8
】
ERROR MESSAGES ………………………..….27
【
9
】
SPECIFICATIONS…………………………………28
【
10
】
WARRANTY…………………………………..……28

3
First of all, thank you for purchasing the USA Measurements
Army “iCount” US-iC series electronic counting scale from our
company. The high quality and reliability of our products are
the best in the measurements industry. There are specific
methods of installation, operation, and maintenance in this
manual that are very important to adhere to. In order for your
scale to work well, you must read the manual carefully before
using.
【
1
】
ATTENTION
l Do not let anything drop onto the pan.
l Do put the scale in a dangerous enviornment.
l Keep the scale in a level area unobstructed by objects.
l Do not count pieces on the scale or move around the pan.
l Keep the scale clean. If the product is not going to be
used for a long period of time recharge the battery once a
month. When the scale has been inactive for a period of
time it is necessary to charge the battery before using the
scale again.
l We suggest all maintenance to be done by a technician.

4
1.1 ATTENTION BEFORE USING
1. Place the scale on a clean, firm, flat surface without the
pan on top and keep away from any kind of vibration, heat, or
harsh changing temperatures. Adjust the 4 leveling feet so
that the bubble is centered in the circle and be sure the scale
is level each time you move the product.
2. Connect the AC adapter to an independent power supply to
avoid interference from other equipment.
3. Scale pan must be empty when turning on the scale.
4. The first time setting up the scale wait 3-5 minutes for the
scale to autocalibrate.
5. For best weighing accuracy, the center of gravity for an
object should be placed in the center of the pan and not in the
corner or edge of pan.
【
2
】
INSTALLATION
2.1 BODY INSTALLATION
1
．
Contents in Carton
No.
Name
Unit
Qty.
1
Body
pc
1
2
Pan
pc
1
3
Manual
pc
1

5
4
Calibration
pc
1
5
Inner Packing
pc
1
6
AC Adapter
pc
1
2. Put the scale on a firm and horizontal surface, adjust the
feet to keep the scale stable and level the feet till the bubble is
centered in the circle.
3. Put the pan on the body and press
【
ON/OFF
】
key to turn on
the scale in weighing mode.
2.2 BATTERY REPLACEMENT
1. Take off the stainless steel pan, open the housing, and
disconnect the battery connectors.
2. Install the new battery in same position and connect
negative and positive poles correctly.
Warning
：
The positive and negative poles of lead-acid battery
installed incorrectly can cause a short circuit or electrode
reverse, which will damage the battery and may cause a fire.
Connection: Red wire to red pole and black wire to black pole.
3. Screw back in the housing and place the weighing pan on
the scale. After that the battery replacement is complete.

6
【
3
】
INSTRUCTION
3.1 PARAMETERS
Accuracy
：
III
Number of Division
：
(3000-300000
）
d
，（
3000d,dual range
）
approved
Working Voltage
：
5V
Sample Rate: 20 times/Sec.
Resolution
：
1 million
3.2 POWER SUPPLY
AC Adapter
：
Input 100V~240V
，
Output 12V/1A
Battery Specification: 6V4AH
【
4
】
DISPLAY
4.1 PANEL DESCRIPTION
US-iC Panel

7
Description
：
HI (red light),OK (green light) and LO (yellow
light) indicates when check weight function works.
4.2 KEY DESCRIPTION
【
0~9
】：
The input number displayed on the screen
【
.
】：
Decimal Point
【
C
】：
Clear the displayed numbers on screen
【
SMPL
】：
Calculate a new average unit weight
【
RSMPL
】：
Recalculate a new average unit weight
【
ON/OFF
】：
Powers unit on or off
【
TARE
】：
Perform Tare Function
【
ZERO
】：
Perform Zero Setting Function
【
PRINT
】：
Perform Print Function
【
UWS
】：
Confirm the input unit weight value
【
CK
】：
Cooperate with other keys to set the upper-lower limit
【
RETURN
】：
Return to weighing interface when setting
【
M+/HI
】：
1. Perform accumulation function in weighing mode,
then the symbol M+ is bright 2. Cooperate with check weight
key to input the upper limit.
【
MR/LO
】：
1. Perform to redisplay function in weighing mode,
then the symbol MR is bright

8
2.Cooperate with check weight key to input the lower limit.
【
MC
】：
Press to clear accumulated value , then the symbol
MC is eluminated.
Notice:
：
The time for pressing any key is less than 1 second.
4.3 DISPLAY DESCRIPTION
No.
Description
No.
Description
1
Stable Symbol
7
MR Symbol
2
Zero Symbol
8
MC Symbol
3
- Symbol
9
R1 cap. Symbol
4
NET Symbol
10
R2 cap. Symbol
5
Battery Symbol
11
Samples Lack
6
M+ Symbol
Input Unit Weight Lack
Weight Unit Weight
COUNT
1
2
3
4
5
6
7
8
9
10
11

9
【
5
】
OPERATION
5.1 TURN ON/OFF
ON
：
Press
【
ON/OFF
】
key to display the maximum capacity
and software version on the display, scale will perform a
self-inspection, and then enter into the weighing mode.
OFF
：
Press
【
ON/OFF
】
key to turn off the scale.
5.2 COUNTING MODE
There are three display windows in the US-iC series scale, in
which weight, unit weight and count are displayed.
5.3 AVERAGE UNIT WEIGHT SETTING
If average unit weight was not set beforehand, “0” will be
displayed in the unit weight and count screen.
Sampling
：
1. Place a samples onto the weighing pan.
2. Input the number of samples by numeric keyboard, and
then input numbers are displayed on unit weight screen .

10
3. Press
【
SMPL
】
key to display the unit weight value on unit
weight screen and the sampling value on count screen.
4. The set average unit weight and number are displayed on
the screens.
Sampling After Tare:
1. Put a container on the pan
2. Press
【
TARE
】
key to display “0” on weight screen.
and NET symbol is displayed.
3. Put samples inside the container
4. Input the number of samples by numeric keyboard and the
number is displayed on unit weight screen.
5. Press
【
SMPL
】
key to display the unit weight value on unit
weight screen and sampling value on count screen.
Input a known average unit weight:
1. A known unit weight is input, then press
【
UWS
】
key to
display “ unit weight value” on unit weight screen.
2. Put entire sampled units onto the pan
3. Count and get the result