USASPEC A2D-RCA Instruction Manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2D-RCA
QUICK START INSTALLATION GUIDE FOR RADIOS WITH AUXILIARY INPUT

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This document is provided as a GENERAL installation guide, some vehicles vary and may
require additional steps. We do not accept responsibility for third party labor charges or
modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirements
CD changer controlling radio
Introduction
Many have aftermarket stereos with Auxiliary inputs jacks (RCA) or factory
radios with an auxiliary input adapter for their audio devices. With the A2D-RCA
add-on you no longer have to deal with plugs and connectors. The A2D-RCA
automatically connects to Smartphone, Kindle, or Tablet upon entering vehicle.
Stream turn-by-turn directions, music Apps (e.g. Pandora, Spotify) directly into
Stereo. This leaves no wires or clutter on or around dashboard and is a welcome
upgrade for those with Bluetooth enabled devices.
See Frequently Asked question at the end of this guide for details.
Installation
All Radios (factory or aftermarket) must have RCA Audio inputs or an
auxiliary input adapter for the A2D-RCA to work.
1. Remove radio from dash or locate auxiliary input adapter in trunk, center
armrest, glove box etc. Auxiliary input adapters are available from USASpec,
Blitzsafe, PIE, Peripheral, iSimple, PAC and others (See Fig. 1)
Fig. 1
Auxiliary input adapter (not included)
2. Connect male RCA’s from module (See Fig. 2) to RCA inputs of existing
auxiliary input adapter (See Fig. 1) or to RCA Inputs of Aftermarket
stereo.
Fig. 2
RCA’s and power connections
3. Connect Red Wire to 12V Accessory supply and black Wire to ground
(See Fig. 2)
4. Secure module and proceed to next section.

Pairing
Pairing varies among devices but basic steps are the same. This process is done
upon initial install and will not have to be repeated
1. Turn Ignition and Radio “ON”
LED flashes
2. On A2DP device: go to Settings, Wireless & Networks, Bluetooth
Settings
3. Select Bluetooth and turn on.
4. Select Bluetooth settings
5. Tap Scan for devices .
6. Wait for Bluetooth device name to appear and select it. Once paired
LED will glow steady
Operation
1. Turn stereo “ON”
2. Set radio to “AUX” Mode
3. Launch Smartphone or tablet streaming application.
4. Use stereo volume control button to set the playback level. If distorted,
lower volume on audio device or if inaudible, raise volume on device.
Warning! Playlist and Track selection is *NOT* possible from the stereo.
Use the smartphone built-in controls to access and control the audio files.
5. If correct operation is confirmed go ahead and reinstall stereo.
6.
Optional
Remote control
Optional remote control allows users to:
1. Control music wirelessly
2. Activate Phone commands (Siri, Google play etc.)
3. Track up/down
4. Volume up/down
Pairing:

Operation:
Use wireless remote to perform the following functions on any iOS7.0 and higher
or Android 4.4 and higher.
Package contents:
Frequent ask questions & troubleshooting
1. Does the A2D-RCA work on all radios?
NO; Works on stereos with RCA Audio inputs
2. Can I connect red wire to a permanent +12V source instead of
accessory source?
YES;but it’s not recommended.
3. Do I have to pair this adapter each time I get into vehicle?
NO; once paired the A2D-RCA connects automatically
4. My stereo does not have audio inputs and I would like to install the
A2D-RCA. What are my options?
If stereo (factory or aftermarket) does not have RCA inputs, you must first
purchase an auxiliary input adapter.
5. Can I use the A2D-RCA for Bluetooth hands free calls?
NO; the A2D-RCA does not support Hands-Fee Calling (HFP)
6. How does it work if paired to more than one device?
More than one device can be paired, however the device that was last used
gets priority. To pair connect a second device simply un-pair first.
7. Will I be able to connect the A2D-RCA tohome stereo?
YES, so long you can provide 12V DC (AC to DC converter required) and
home stereo has RCA audio inputs.
email [email protected]om
© 1995-Sep-21 Discount Car Stereo, Inc. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademarks or registered trademarks of their respective companies or mark holders.