V-fit-ST HERCULEAN STB09-4 Manual

SERIAL NO. AB2632-UK
HERCULEAN STB09-4 FOLDING WEIGHT BENCH
Assembly & User Manual
use your new product and retain for future use
Please ensure that you read this manual
carefully before attempting to assemble or

Contents
Section Page
General Information . . . . . . 4
Before You Start . . . . . . . . . 5
Safety . . . . . . . . . . . . . . . . . 6
Exercise Information . . . . . . 7
Assembly . . . . . . . . . . . . . . 14

General Information
Quality
This exercise product has been designed and
manufactured to comply with the latest (BS EN
957) British and European Safety Standards.
Questions
Should you encounter any difficulty with the
assembly, operation or use of your exercise
product or if you think that you may have parts
missing, please DO NOT return it to your retailer
but contact us first for help and advice, asking for
CUSTOMER SUPPORT, by any of the following
means.
Tel:- 01535 637711 or
Fax:- 01535 637722 or
Email:- [e-mail]
Website:- www.benysports.co.uk
CUSTOMER SUPPORT is open from 9.00am to
5.00pm from Monday to Friday
Beny Sports Co. UK Ltd.
Unit 8, Riparian Way,
The Crossings, Cross Hills,
West Yorkshire
BD20 7BW
Queries
If you do have any queries, please ensure that
you have the following information ready for our
Customer Support Staff:
YOUR NAME
YOUR ADDRESS
YOUR PHONE NUMBER
PRODUCT MAKE OR BRAND
PRODUCT MODEL
PRODUCT SERIAL NUMBER
DATE OF PURCHASE
NAME OF RETAILER
PART NUMBERS REQUIRED
Guarantee
Beny Sports Co. UK Ltd. guarantee's its product
range for DOMESTIC USE ONLY.
For specific guarantee periods please consult the
Guarantee Registration Card supplied with your product.
a). provide parts for the purchaser to effect repair.
b). repair the product returned (at the purchaser's
cost) to our warehouse.
c). replace the product if it is deemed economical
to do so.
This guarantee applies to the original purchaser
only and is not transferable.
This guarantee does not cover wear and tear on
upholstery or consumables.
This guarantee does not cover abuse or defects
caused by storage or use outside those intended.
If you need to advise us of a defect with your
product, we will ask for proof of purchase. To
enable us to service your requirement for
replacement parts, you must return the enclosed
Guarantee Registration Card within 14 days of
purchase. Failure to do so will result in any claim
for replacement parts or repairs being refused.
This does not affect your statutory rights as a
consumer.
Customer Support
Tel:- 01535 637711 or
Fax:- 01535 637722 or
Email:- [email protected]
Website:- www.benysports.co.uk
CUSTOMER SUPPORT is open from 9.00am to
5.00pm from Monday to Friday
Beny Sports Co. UK Ltd.
Unit 8, Riparian Way,
The Crossings, Cross Hills,
West Yorkshire
BD20 7BW
During the Guarantee Period we have the right to: -
Page 4

Before You Start
Page 5
Tools
To enable you to successfully assemble your product. You will require 1 x 13mm, 2 x 14mm Combination
Spanners and 1 x Screw Driver, you may also find it beneficial to have a Soft-Headed
Hammer and perhaps an Adjustable Spanner handy as this may help.
Prepare the Work Area
It is important that you assemble your product in a clean, clear, uncluttered area. This will enable you to
move around the product while you are fitting components and will reduce the possibility of injury
during assembly.
Work with a Friend
You may find it quicker, safer and easier to assemble this product with the help of a friend as some of
the components may be large, heavy or awkward to handle alone.
Open the Carton.
Carefully open the carton that contains your product, taking note of the warnings printed on the carton
to ensure that the risk of injury is reduced. Be aware of sharp staples that may be used to fasten the
flaps as these may cause injury. Be sure to open the carton the right way up, as this will be the easiest
and safest way to remove all the components.
Unpack the Components
Carefully unpack each component, checking against the parts list that you have all the necessary parts
to complete the assembly of your product.
Please note that some of the parts may be pre-fitted to major components, so please check carefully
before contacting our CUSTOMER SUPPORT team.
In any event, please do not return the product to your retailer before contacting us first.

Safety
Before you undertake any programme of exercise that will increase cardiovascular activity please be
sure to consult with your doctor. Frequent strenuous exercise should be approved your doctor and
proper use of your product is essential. Please read this manual carefully before commencing
assembly of your product or star ting to exercise.
* Please keep all children away from exercise products when in use. Do not allow children to climb or
play on them when they are not in use.
* For your own safety, always ensure that there is at least 1 Metre of free space in all directions
around your product while you are exercising.
* Regularly check to see that all nuts, bolts and fittings are securely tightened. Priodically checking
all moving parts for obvious signs of wear or damage.
* Clean only with a damp cloth, do not use solvent cleaners. If you are in any doubt, do not use your
product, but contact CUSTOMER SUPPORT by any of the means listed on the
opposite page.
* Before use, always ensure that your product is positioned on a solid, flat sur face. If necessary,
use a rubber mat underneath to reduce the possibility of slipping in use.
* Always wear appropriate clothing and footwear such as training shoes when exercising. Do not wear
loose clothing that could become caught or trapped during exercise.
Storage and Use
Your product is intended for use in clean dry conditions. You should avoid storage in excessively
cold or damp places as this may lead to corrosion and other related problems that are outside our
control.
Conformity
This product conforms to:
BS EN ISO 20957 - 1 and BS EN 957 - 4 - Class (H) - HOME USE - Class (C).
It is NOT suitable for therapeutic purposes.
If any part of your product
becomes damaged, broken
or badly worn do not use
the equipment until the
defective parts have been
replaced
Warning
Weight Limits
This product is suitable for users weighing a MAXIMUM of 110kg
The TOTAL WEIGHT LOADING on this product INCLUDING the user plus any weights and accessories is 200kg
The MAXIMUM STATIC LOADINGS of the individual workstations are: -
Barbell Stands – 120kg* but not to exceed the 200kg TOTAL WEIGHT LOADING
Leg Extension – 35kg
Pec Deck (where fitted) – 25kg
Squat Stands (where fitted) – 80kg* to be used only with 50kg on the Leg Extension to provide balance
Lat Tower (where fitted) – 35kg
DO NOT EXCEED THESE WEIGHT LIMITS AS DAMAGE MAY OCCUR TO THE
PRODUCT & SERIOUS INJURY COULD RESULT
USER WEIGHT – kg BARBELL WEIGHT LIMIT - kg
60kg 120kg
70kg 120kg
80kg 120kg
90kg 110kg
100kg 100kg
110kg 90kg
Page 6

Page 7
Exercising Information
Beginning
How you begin to exercise will vary from person to person. If you
have not exercised for a long period of time, have been inactive for a
while, or are severely overweight you MUST start slowly, increasing
your exercise time gradually, by perhaps only a few minutes for each
session per week.
Combine a carefully structured nutritious diet with a simple but
effective exercise routine and this can help make you feel better, look
better and will almost certainly enable you to enjoy life more.
Aerobic Fitness
Aerobic exercise is simply defined as any sustained activity that
increases the supply of oxygen to your muscles via the blood pumped
by your heart. With regular exercise, your cardiovascular system will
become stronger and more efficient. Your recovery rate i.e. the time
taken for your heart to reach its normal resting level, will also
decrease.
Initially you may only be able to exercise for a few minutes each day.
Do not hesitate to breathe through your mouth should you need more
oxygen. Use the "talk test". If you cannot carry on a conversation
while exercising, you are working too hard! However, aerobic fitness
will be gradually built up with regular exercise, over the next six to
eight weeks.
Do not be discouraged if it takes longer than this to begin to feel less
lethargic, everyone is different and some will achieve their targets
quicker than others. Work at your own, comfortable pace and the
results will come. The better your aerobic fitness the harder you will
have to work to stay in your target zone.

Exercising Information
USERS
AGE
(Years)
20-24
25-29
30-34
35-39
40-44
45-49
50-54
55-59
60 and over
UNCONDITIONED
TARGET ZONE - A
(Beats per Minute)
145 - 165
140 - 160
135 - 155
130 - 150
125 - 145
120 - 140
115 - 135
110 - 130
105 - 125
CONDITIONED
TARGET ZONE - B
(Beats per Minute)
155 - 175
150 - 170
145 - 165
140 - 160
135 - 155
130 - 150
125 - 145
120 - 140
115 - 135
Warm Up
A successful exercise programme consists of three parts, Warm Up, Aerobic Exercise and Cool Down.
Never start a training session without warming up. Never finish one without cooling down correctly.
Perform between five and ten minutes of stretching before starting your workout to prevent muscle
strains, pulls and cramps.
Aerobic Exercise Session
Those new to exercise should exercise no more than every other day to start with.
As your fitness level increases, increase this to 2 in every 3 days.
When you are comfortable with your routine, exercise for 6 days per week. Always take at least one day
off per week.
Exercising in your Target Zone
To ensure that your heart is working in its exercise target zone, you need to be able to take your pulse.
If you do not have a pulse monitor (either from the product you are using or a proprietary independent
unit) you will need to locate the pulse in your carotid artery. This is situated in the side of the neck and
can be felt by using the index and middle fingers. Simply count the number of beats you feel in 10
seconds and then multiply by six to get your pulse rate. This should be taken before you start to
exercise for easy reference.
People who have a greater aerobic fitness, have a lower resting pulse level and will also be able to
exercise with a higher pulse level.
Target Zone
To determine your target zone, see the chart opposite. If you are new to exercise and by definition unfit,
refer to the left column. If you exercise regularly and have good aerobic fitness, refer to the right
column.
Incorrect or excessive
training may damage your
health. Please read the
exercise information first.
Note
Page 8

Page 9
Exercising Information
Hamstring Stretch
Sit on the floor with your right leg extended and
place your left foot flat against the right inner
thigh. Stretch forward toward the right foot and
hold for 10 seconds. Relax and then repeat with
the left leg extended.
Repeat 2 - 3 times.
Cool Down
To decrease fatigue and muscle soreness, you should also cool down by walking at a slow relaxed pace
for a minute or so, to allow your heart rate to return to normal.
Warm Up and Cool Down Exercises
Hold each stretch for a minimum of ten seconds and then relax. Repeat each stretch two or three
times. Do this before your Aerobic Exercise session and also after you have finished.
Head Roll
Rotate your head to the right for one count,
feeling a slight pull on the left side of your neck.
Next, rotate your head back for one count,
stretching your chin. Then rotate your head to the
left for one count, feeling a slight pull on the right
side of your neck. Lastly, drop your head to your
chest for one count. Repeat 2 to 3 times.
Toe Touch
Slowly bend forward from your waist, letting your
back and shoulders relax as you lower your trunk.
Gently stretch down as far as is comfortable and
hold for 10 seconds.
Shoulder Lift
Rotate and lift your right shoulder up towards
your ear for one count. Relax then repeat for the
left shoulder.
Repeat 3 - 4 times.
Calf / Achilles Stretch
Turn towards the wall and place both hands on it.
Support yourself with one leg while the other is
placed behind you with the sole flat on the floor.
Bend the front leg and lean towards the wall,
keeping the rear leg straight so that the calf and
Achilles tendon are stretched hold for 5 seconds.
Repeat with the other leg.
Repeat 2 - 3 times.
Side Stretch
Open both arms to the side and gently lift them
above your head. Reach your right arm as high as
you can for one count, gently stretching the
muscles of the stomach and lower back. Repeat
the action with your left arm.
Repeat 3 - 4 times.
Inner Thigh Stretch
Sit on the floor and pull your legs toward your
groin, the soles of your feet together. Hold your
back straight and lean forward over your feet.
Tighten the thigh muscles and hold for 5
seconds. Release and repeat 3 - 4 times.

Exercising Information
Basic Aerobic Training Programme
For your basic Aerobic Exercise routine we suggest that you try the
following. Remember, breathe correctly, exercise at your own pace
and do not over-train as injury may result.
Week 1 & 2
Warm Up 5 - 10 Minutes
Cool Down 5 Minutes
Week 3 & 4
Warm Up 5 - 10 Minutes
Cool Down 5 Minutes
Week 5 & 6
Warm Up 5 - 10 Minutes
Cool Down 5 Minutes
Week 7 & 8
Warm Up 5 - 10 Minutes
Cool Down 5 Minutes
Week 9 & beyond
Warm Up 5 - 10 Minutes
Cool Down 5 Minutes
Exercise 4 minutes at 'A'
Rest 1 minute
Exercise 2 minutes at 'A'
Exercise slowly 1 minute
Exercise 5 minutes at 'A'
Rest 1 minute
Exercise 3 minutes at 'A'
Exercise slowly 2 minutes
Exercise 6 minutes at 'A'
Rest 1 minute
Exercise 4 minutes at 'A'
Exercise slowly 3 minutes
Exercise 5 minutes at 'A'
Exercise 3 minutes at 'B'
Exercise 2 minutes at 'A'
Exercise slowly 1 minute
Exercise 4 minutes at 'A'
Exercise slowly 3 minutes
Exercise 5 minutes at 'A'
Exercise 3 minutes at 'B'
Exercise 2 minutes at 'A'
Exercise slowly 1 minute
Repeat entire cycle 2 or 3
times
This is only a suggested programme and may not suit every
individual's needs.
Page 10

Exercising Information
GETTING STARTED
You will often read about terms referring to exercise that may be confusing. Below are some of the
definitions that are regularly used.
Repetition - Commonly referred to as 'REPS'.
This is a complete movement from start to finish.
Set - This is a complete number of consecutive repetitions.
i.e. 1 set of 10 reps.
Speed of Motion - This is the relative speed of movement for each rep.
Fast is considered as 1 rep / second. Medium is 1 rep / 2 seconds. Slow is 1 rep /
4 seconds.
Intensity - How 'hard' the exercise feels.
Low Intensity = easy exercise. High Intensity = hard exercise.
TRAINING PROGRAMMES
You will achieve fast results, gaining a trimmer, fitter body if you follow these general rules.
* Exercise regularly - do not skip workouts as consistency is the first key to success.
* Do not be afraid perspire a little. This is a sign that you are working your body hard enough to give
fast results. You will find 'hard' exercise enjoyable.
* Set yourself realistic goals. Do not be over-ambitious. Plan your workouts to concentrate on
specific body areas. Start slowly and gradually increase the intensity, reps and sets.
BEGINNERS PROGRAMME
This is a short suggested programme which we suggest you use for no more than 3 weeks, to be
ideally performed every other day, but certainly not more than 4 times during the week.
This suggested routine is specifically for beginners or those who have not exercised for a considerable
time. The programme is designed to provide general improvement in muscle tone, strength, flexibility
and co-ordination.
As a beginner, you should start with no more than 2 sets of 6 exercises for the following reps on each
of the GymÕs training stations.
10 REPS - BENCH PRESS followed by LAT PULLDOWNS
5 REPS - PEC DEC
10 REPS - SHOULDER PRESS
10 REPS - LEG EXTENSIONS followed by LEG CURLS
* Your rest interval between each set of reps should be 1 minute.
* You should perform 2 SETS of each exercise.
* Your exercise pace should be SLOW to MEDIUM.
* The resistance (weight) settings should be in positions 1 - 3.
* This exercise programme should take you approximately 20 minutes.
* Follow this exercise programme with 5 minutes of proper cool down exercises.
Page 11

Exercising Information
INTERMEDIATE EXERCISE
This is a slightly longer programme which we suggest you use for the next 6 - 8 weeks, to be ideally
performed not more than 5 times during the week.
This suggested routine is specifically for intermediate users or those that are familiar with exercise
routines. The programme is designed to increase muscle definition, build strength, aid flexibility and co-
ordination.
The increase in exercise intensity and speed of repetitions is key to your success at this stage.
For intermediate exercise we recommend 3 - 4 sets of 8 exercises for the following reps on each of the
Gym's training stations.
15 REPS - BENCH PRESS followed by LAT PULLDOWNS
10 REPS - PEC DEC
15 REPS - SHOULDER PRESS
15 REPS - LEG CURLS
15 REPS - LEG EXTENSIONS followed by ARM CURLS
* Your rest interval between each set of reps should be 1 minute.
* You should perform 3 - 4 SETS of each exercise.
* Your exercise pace should be MEDIUM to FAST.
* This exercise programme should take you approximately 35 - 40 minutes.
* Follow this exercise programme with 5 minutes of proper cool down exercises.
ADVANCED TRAINING
This is an open-ended programme, ideally performed not more than 4 times during the week, preferably
on alternate days.
This suggested routine is specifically for advanced users or those that are familiar with exercise
routines. The programme is designed to increase muscle mass and build strength.
The increase in exercise intensity, resistance levels and speed of repetitions is key to your on going
success.
For advanced training we recommend 4 sets of the 9 exercises for the following reps on each of the
Gym's training stations. However at this stage you may want to concentrate on specific body parts, so
as you are now fully familiar with the workings of your Gym you should be able to structure an exercise
programme to suit your own individual needs. Any specific advice should be sought through specialist
books.
20 REPS - BENCH PRESS followed by LAT PULLDOWNS
15 REPS - PEC DEC
15 REPS - SHOULDER PRESS
15 REPS - LEG CURLS
20 REPS - LEG EXTENSIONS followed by ARM CURLS
15 REPS - LEG PRESS
10 SLOW REPS - 2 SETS - SIT UPS
* Your rest interval between each set of reps should be 1 minute.
* You should perform 4 SETS of each exercise.
* Your exercise pace should be MEDIUM to FAST.
* This exercise programme should take you approximately 40 - 50 minutes.
* Follow this exercise programme with 5 minutes of proper cool down exercises.
Page 12

Exercise Notes
Page 13

Assembly
ACCESSORY FITMENT LIST
The following accessories are supplied in a pack and should be checked before attempting assembly.
The are all the accessories you will need to complete the assembly of your V-fit product.
Page 14
Item 32
Qty 2
Item 47
Qty 2
Item 49
Qty 4
Item 48
Qty 2
Item 27
Qty 3
Item 30
Qty 2
Item 31
Qty 5
Item 26
Qty 21 Item 29
Qty 6
Item 23
Qty 26 Item 25
Qty 16
Item 24
Qty 2
Item 28
Qty 2
Item 61
Qty 2
Item 19
Qty 4
Item 44
Qty 1
Item 67
Qty 3
Item 18
Qty 1
Item 17
Qty 14
Item 68
Qty 3
Item 20
Qty 3
Item 21
Qty 1 Item 16 Qty 4 Item 15 Qty 4
Item 46
Qty 2
Item 62
Qty 3
Item 50
Qty2
Item 22
Qty 8

Assembly
Connect both Uprights (2) to the Upright Support Bar (3) using 4 x M8 x 50mm
Carriage Bolts (17) fitted from the inside as per illustration, 4 x M8 Flat Washers (23)
and 4 x M8 Nylon Locknuts (26).
Place both Uprights (2) on the outside of the Rear Stabiliser (1) and secure in place using 2 x
M8 x 85mm Carriage Bolts (19) fitted from the outside, 2 x M8 Flat Washers (23)
and 2 x M8 Nylon Locknuts (26).
Now attach both Stabiliser Brackets (13) to the inside of both Uprights (2) using 2 x M8 x
50mm Carriage Bolts (17), 2 x M8 Flat Washers (23) and 2 x M8 Nylon Locknuts (26),
and in between the Rear Stabiliser (1) and Squat Stand Tubes (52) using 2 x M8 x 85mm
Carriage Bolts (19), 2 x M8 Flat Washers (23) and 2 x M8 Nylon Loknuts (26).
Connect the Squat Stand Link Plates (54) to the INSIDE of each Upright and Squat Stand Tube
Using 4 x M8 x 50mm Carriage Bolt (17), 4 x M8 Flat Washer (23) and 4 x M8 Nylon Locknut
1
Note
PART No. DESCRIPTION . . . . . . . . . . . . . . QTY
Assembly Accessories 1
17 M8 x 50mm CARRIAGE BOLTS . . . . . .
19 M8 x 85mm CARRIAGE BOLTS . . . . . .
23 M8 FLAT WASHERS . . . . . . . . . . . . . .
26 M8 NYLON LOCKNUTS . . . . . . . . . . . .
30 BARBELL LOCKING PINS . . . . . . . . . . .
(26) for each fitting. Now fit the Barbell Locking Pins (30) through the holes in the top of both
Uprights (2) as shown below.
Do not fully tighten at this stage.
10
4
14
14
2
Do NOT FULLY TIGHTEN any
Bolts, Nuts or Fittings at this
stage unless specifically
instructed to do so.
Note
Page 15

Assembly
Connect the REAR of the Main Frame (4) to the assembled Uprights using 1 x M10 x 60mm Hex Head
The highest posilion will give
the greatest intensity during
exercise.
Bolt (20), 2 x M10 Flat Washers (25) and 1 x M10 Nyion Locknut (29) bolted from the SIDE.
Place an M8 x 90mm Carriage Bolt (44) in the UPPER hole and secure in position using 1 x M8 Flat
Washer (23) 1 x M8 Spring Washer (24) and 1 x M8 Locking Knob (Female) (28). Tighten securely to
lock the frame in position.
Fit the Front Stabiliser (5) to the Leg Extension Upright (6) and secure with 3 x M8 x 15mm HEX Bolt (67) ,
Flat3 x M8 Washer(23). Connect the assembled Leg Extension Upright to the FRONT of the Main Frame (4)
using 1 x M10 x 60mm Hex Head Bolt (20), 2 x M10 Flat Washers (25) and 1 x M10 Nylon Locknut (29)
bolted from the SIDE.
Place an M8 x 55mm Carriage Bolt (18) in the UPPER hole and secure in position using 1 x M8 Flat
Washer (23) 1 x M8 Spring Washer (24) and 1 x M8 Locking Knob (Female) (28). Tighten securely to
lock the frame in position.
Fit the Leg Extension Support (7) into the Leg Extension Upright to any one of 3 positions and lock in
position using the M8 Locking Knob (27).
Assemble the Leg Extension (8) to the Leg Extension Support using 1 x M10 x 60mm Hex Bolt (20),
2 x M10 Flat Washers (25) and 1 x M10 Nylon Locknut (29) bolted from the SIDE.
Fit the Weight Support (14) to the Leg Extension (8) using 1 x M8 x 45mm Carriage Bolt (68), 1 x M8 Flat
Washer (23) and 1 x M8 Nylon Locknut (26). Tighten securely and slide on the Weight Retainer Clip (31).
Slide a Foam Roller (40) onto one end of a Leg Extension Pad Bar (9) and fit into
position on the Leg Extension. Slide the remaining Foam Rollers onto the Leg Extension Pad Bars.
2
PART No. DESCRIPTION . . . . . . . . . . . . . . QTY
Assembly Accessories 2
67 M8 x 15mm HEX BOLT. . . . . . . . . . .
18 M8 x 55mm CARRIAGE BOLTS . . . . . .
44 M8 x 90mm CARRIAGE BOLTS . . . . . .
20 M10 x 60mm HEX BOLT . . . . . . . . . .
23 M8 FLAT WASHERS . . . . . . . . . . . . . .
24 M8 SPRING WASHERS . . . . . . . . . . . .
25 M10 FLAT WASHERS . . . . . . . . . . . . .
26 M8 NYLON LOCKNUTS . . . . . . . . . . . .
27 M8 LOCKING KNOB (MALE) . . . . . . . . .
28 M8 LOCKING KNOB (FEMALE). . . . . . .
29 M10 NYLON LOCKNUT . . . . . . . . . . . .
31 1
3
2
1
1
6
2
6
3
1
1
3
WEIGHT PLATE RETAINER CLIP . . . . . .
68 1 M8 x 45mm CARRIAGE BOLTS . . . . . .
Note
67
Page 16

Assembly
The Backrest Support Bushings
shoud be placed between the
Backrest Supports and the Main
Frame during assembly.
This will ensure that there is
minimal sideways movement on
the Backrest during use.
Connect the Backrest Supports (11) to the Main Frame (4) using the fittings in the
following sequence. 1 x M10 x 130mm Hex Bolt (21), 1 x M10 Flat Washer (25),
1 x Backrest Supports (11) 1 x Backrest Support Bushing (32) on one side then 1 x
1 x Backrest Support Bushing (32) Backrest Support (11), 1 x M10 Flat Washer (25)
and 1 x M10 Nylon Locknut (29). Tihgten securely to remove all free-play but take care
Fit the Seat (42) to the seat bracket (12) using 4 x M6 x 15mm Bolts (15) and 4 x M6
Flat Washers (22). Pre-fitted to the UNDER side of the seat
The Backrest can be adjusted into 4 positions for convenient use. (Flat and 3 Inlcine Positions).
Please ensure that the Backrest Adjustment Rod (10) is positioned UNDER the Backrest
Supports and is secured into place in any one of the 3 adjustement holes in the Uprights
before use.
3
Note
PART No. DESCRIPTION . . . . . . . . . . . . . . QTY
Assembly Accessories 3
21 M10 x 130mm HEX BOLT . . . . . . . . . .
25 M10 FLAT WASHERS . . . . . . . . . . . . .
29 M10 NYLON LOCKNUT . . . . . . . . . . . .
32 BACKREST SUPPORT BUSHINGS . . . . . 2
1
2
22 M6 FLAT WASHERS . . . . . . . . . . . . . 6
16 M6 X 40mm BOLTS . . . . . . . . . . . . . 4
15 M6 X 15mm BOLTS . . . . . . . . . . . . . 2
1
Fit the Backrest (41) to the Backrest Supports (11) using 4 x M6 x 40mm Bolts (16)
and 4 x M6 Flat Washers (22).
NOT to overtighten.
16
22
Page 17

Assembly
Note
4
68 M8 x 45mm CARRIAGE BOLTS . . . . . . 2
23 M8 FLAT WASHERS . . . . . . . . . . . . . . 2
25 M10 FLAT WASHERS . . . . . . . . . . . . . 4
26 M8 NYLON LOCKNUTS . . . . . . . . . . . . 2
31 2
46 M10 x 125mm HEX BOLTS . . . . . . . . . 2
47 PLASTIC SPACER . . . . . . . . . . . . . . . . 2
48 M10 LOCKING KNOB (FEMALE) . . . . . .2
49 BUTTERFLY ARM BOLT BUSHINGS . . . 4
WEIGHT PLATE RETAINER CLIP . . . . . .
PART No. DESCRIPTION . . . . . . . . . . . . . . QTY
Assembly Accessories 4
Slide a Butterfly Arm Pad Bar (45) into each Butterfly Arm (43) , now slide 1 x Foam Roller (40) onto each
Butterfly Arm Pad Bar (45).
Fit a Weight Support (14) to each Butterfly Arm using 1 x M8 x 45mm Carriage Bolt (68), 1 x M8 Flat
Washer (23) and 1 x M8 Nylon Locknut (26). Tighten securely and slide on the Weight Retainer Clip (31).
Fit 2 x Butterfly Arm Bolt Bushings (49) to each Upright - 1 each side of each Upright. Pass an M10 x
125mm Hex Bolt (46) through an M10 Flat Washer (25) and then through the front face of an assembled
Butterfly Arm. Slide on a Plastic Spacer (47) then fit the assembly to the appropriate Upright.
Secure the assembly in place with either: - 1 x M10 Flat Washer (25) and M10 Locking Knob (Female) (48).
Now fully tighten all nuts
and bolls.
Page 18

Assembly
Set a Squat Stand Insert (53) at the desired height in each Squat Stand Tube and
secure in place with 1 x M8 Locking Knob (27) for each side.
5
27 M8 LOCKING KNOB (MALE) . . . . . . . . . 2
PART No. DESCRIPTION . . . . . . . . . . . . . . QTY
Assembly Accessories 5
Page 19

Assembly
Fit the Preacher Curl Pad (51) to the Preacher Curl (55) using 2 x M6 x 16mm Bolts
(15) and 2 x M6 Flat Washers (22).
Secure in place at the desired height (after having removed the Leg Extension) using
the M8 Locking Knob (Male) (27).
6
Page 20