V-GREAT VG-6617S User manual

VSL3.928.011VGASY
1
1. Feature
Used as an warning device to generate fire alarm;
Installation and wiring same as detector base;
Driven by detection circuit, no need for extra power
line.Two adjustable modes, sharing the same address
of detector, or occupying an individual address.
2. Description
VG-6617S Digital Alert Base is designed for the application inside a closed room. As a warning
device, the base will generate alarm sound when the detector detects a fire occurred. Installed as a
base, it is compatible with the range of digital detectors. For application, when sharing the same
address with detector, the alert base will be triggered by that detector installed. Setting with an
individual address, the alert base can be as used a field warning device and activated by C&E Logic.
It is usually installed in hotel room, residential bedroom or other locations that are far away from the
audible and visual alarm..
3. Technical Data
Operating voltage:
Loop voltage: 24V /Allowance range: 15V~28V (Vp-p)
Operating current:
Standby current: ≤ 0.2mA
Action current: ≤ 3mA
Total starting current at alarm state both for the detector and
alert base ≤ 3.5mA (maximum 20 pieces triggered at exactly
the same time)
Address
1~254
Sound level
>75dB
Tonal modification cycle
0.6~1.5S
Temperature:
-10℃~+55℃
Relative humidity
≤95%，non-condensing
Weight
67g
Shell material and color
ABS+PC, White
Dimension
diameter of 102mm, height of 25.5mm
Installation hole distance
73mm
Wiring: directly connected with the detection loop of the control panel.
VG-6617S Digital Alert Base
Base
Installation and Operation Manual V1.00

VG-6617S Digital Alert Base Installation and Operation Manual V1.00
VSL3.928.011VGASY
2
4. Dimension
5. Status Indication
➢Polling: The red indicator flashing with no audible alarm.
➢Alarm: The red indicator is off with an audible alarm.
➢Fault: The red indicator is off with no audible alarm.
6. Installation and Wiring
1) The flame resistant twisted-pair ZR-RVS-2×1.0~1.5mm2 is recommended to be used for the
wiring.
2) Before the installation, please check whether the shell is intact without any damage, and
whether the label is complete.
3) Alert base terminals wiring diagram: The terminals labeled as 1 and 2 on the alert base shall
be connected with the detection loop.
(L+, L-: the detection loop terminal, non-polarized. The 1 and 2 terminals of the alert base shall
be connected with L+ and L-, respectively.)
4) The alert base and detector shall be installed as the following diagram:
Loop Non-polarized
L+
L-

VG-6617S Digital Alert Base Installation and Operation Manual V1.00
VSL3.928.011VGASY
3
5) During the installation, the sound hole shall aim at an open space without any obstacle or
foreign matter blocking it.
Warning:
Before installing the device, please turn off
the power of the control panel.
The installation location shall be free from
rain or moisture, and direct sunlight shall
be avoided
7. Usage and Operation
Addressing: The digital programmer VG-6537 can be used for program the address. For addressing,
connect the programmer with the detection loop terminal, input the address code of the alert base
(1- 254), and press the “Writing” button. (The detailed info is available in VG-6537 Digital
Programmer User Manual.)
Mode setting: There are two adjustable address modes available, sharing the same address with
detector or occupying an individual addess. (the default mode from the factory is sharing the same
address with detector.)
Same address mode: The alert base and detector use the same circuit address. If the detector sends
an alarm, the alert base connected with it will send an audible alarm.
Individual addresses mode: The alert base and the detector each occupy one circuit address. Used
as an warning device, the application is similar to an sounder such as VG-6737 Digital Sounder
Beacon. C&E logic can be programmed between the alert base and detection devices such as digital
detectors. If the detector sends an alarm, the alert base relevant to it will send an audible alarm.
The two modes shall be switched by the programmer. (The detailed info is available in VG-6537
Digital Programmer User Manual.)
Silence: Resetting the control panel can silence the alarm of the alert base.
Attention: The total starting current at alarm state for the detector and alert base ≤3.5mA. Please
reference the following table:
Step 1: Align Sign A of the detector body
with Sign B of the base.
Step 2: Rotate the detector clockwise
until Sign A is aligned with Sign C, then
the installation is finished.
Sound Hole

VG-6617S Digital Alert Base Installation and Operation Manual V1.00
VSL3.928.011VGASY
4
Detection loop(Detector + Alert Base)
Load Quantity
Staring Quantity of
Detector + Alert Base Alarm at the same time
≤254 Pieces
≤20 Pieces
≤128 Pieces
≤30 Pieces
8. Attentions
1) If the alert base alarm cannot be started, inspect whether the alert base is damaged.
2) The staff on duty shall be familiar with the operation procedure of the device, and shall avoid
incorrect operations.
3) This alert base is a kind of fire production product. During the usage, the duty system, the
shift handover and takeover system shall be implemented strictly. And the running record shall
be well done.
4) After the alert base is put into service, it shall be inspected regularly. And the function test is
suggested to be performed at least once half a year.
Company: V-GREAT GLOBAL CORPORATION
Add.: Second Floor, Capital City, Independence Avenue, P.O. Box 1008, Victoria, Mahe, Seychelles