V-TAC VT-2421 User manual

INSTRUCTION MANUAL
LED SYNC CONTROLLER RGB
TECHNICAL DATA
MODEL VT-2421
SKU 3340
OUTPUT 3 Channel
STATIC POWER
CONSUMPTION <1 W
OUTPUT CURRENT <6.6A (Each Channel)
OUTPUT POWER 12V:240W, 24V:480W
RATED LOAD 12V:<240W, 24V:480W
SUPPLY VOLTAGE DC: 12V-24V Optional
REMOTE DISTANCE ≤0m
OPERATION VOLTAGE -20°C to +60°C
IP RATING IP20
DIMENSION 64x81x24 mm
In case of any query/issue with the product, please reach out to us at: [e-mail]
For More products range, inquiry please contact our distributor or nearest dealers.
V-TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul.L.Karavelow 9B
MULTI-LANGUAGE
MANUAL QR CODE
Please scan the QR code
to access the manual in
multiple languages.
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions
carefully before starting the installation and keep this manual handy for future reference. If you have any another
query, please contact our dealer or local vendor from whom you have purchased the product. They are trained
and ready to serve you at the best. The warranty is valid for 2 years from the date of purchase. The warranty
does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no
warranty against damage to any surface due to incorrect removal and installation of the product. This product is
warranted for manufacturing defects only.
WARNING
1. Please make sure to turn o the power before starting the
installation.
2. Installation must be performed by a qualified electrician.
3. For Indoor Use only
This marking indicates that this product
should not be disposed of with other
household wastes.
Caution, risk of electric shock.

Receiver can be controlled by any one the same remote as factory default;
remote control delivered with unique
RF code as factory default; if unique-control is needed, please matching the
code before installation and using.
Receiver and Remote Control are coded as default, matching them before using, if unique-control
or new-coded-remote is needed, pairing the remote and the receiver as below operation instruction
before using:
1. Step 1: Pressing key “FLASH” and hold on, power on the controller, the load LEDs will be 50%
brightness white as responding.
2. Step 2: Pressing “FLASH” 3times in 3 seconds, corresponding to the operation, the LED’s bright-
ness will change as 25%-10%-back to preset level.
3. Code learning successfully, the receiver only can be controlled by the remote.
4. If not, please re-operate from step 1 to 2.
• Connect the load wire and sync-signal cable at first, following by the power wire.
• Ensure short circuit can not occur before you turn on the power.
Adopt RF wireless remote control, 20 keys in total, function of each button as below:
Controller adopts the advanced micro control unit, it is used for controlling a variety of LED light. For
instance, point source of light, flexible light strip, wall washer lamp and so on. It has many advan-
tages such as good appearance, easy connection and simplicity to use. Adopts RF 20 key remote
control to ON/OFF, choose colors, change dynamic modes.
DIRECTION OF USE
PRODUCT DESCRIPTION
RF CODE
MATCHING CODE OPERATION
Brightness + Brightness - Pause On/O
Static Red Static Green Static Blue Static White
Static Orange Static Yellow Static Cyan Static Purple
Auto Run Three base color
jumpy
Three color gradually
change Speed +
Flash Seven base color
jumpy
Seven color gradually
change Speed -

Back to factory default, wall-panel can be controlled by any one the same remote control.
1. Step 1: Pressing key “JUMP7” and hold on, power on the controller, the load LEDs will be 50%
brightness white as responding.
2. Step 2: Pressing “JUMP7” 3times in 3 seconds, corresponding to the operation, the LED’s
brightness will change as 25%-10%-back to preset level.
3. Code clearing successfully, the LEDs will be back to the status before the power o, and the
receiver can be controlled by any remote control (any one the same remote control can be used
to clear the code).
4. If not, please re-operate from step 1 to 2.
CLEAR CODE OPERATION
TYPICAL APPLICATION
Port for LEDs output Port for power in