V-tech TELEZAPPER VT 2528 User manual

1
basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury to persons, including the
following:
1. Readandunderstand all instructions.
2. Followallwarnings and instructionsmarked on theproduct.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen sink, or
swimmingpool).
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To
protect it from overheating, these openings must not be blocked by placing the product
on the bed, sofa, rug, or other similar surface. This product should never be placed near
or over a radiator or heat register. This product should not be placed in a built-in
installationwhere proper ventilation isnot provided.
7. This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your
dealerorlocalpowercompany.
8. Do not allow anything to rest on the power cord. Do not locate this product where the
cord will be abused by persons walking on it.
9. Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a risk of fire or electric
shock. Never spill liquid of any kind on the product.
10.To reduce the risk of electric shock, do not disassemble this product, but take it to a
VTechauthorized service facility.Opening or removing cabinet parts other thanspecified
access doors may expose you to dangerous voltages or other risks. Incorrect reassemb-
ling can cause electric shock when the appliance is subsequently used.
11.Do not overload wall outlets and extension cords as this can result in the risk of fire or
electric shock.
12.Unplug this product from the wall outlet and refer servicing to a VTECH authorized
service facility under the following conditions:
A.When the power supply cord or plug is damaged or frayed.
B.If liquid has been spilled into the product.
C.If the product has been exposed to rain or water.
D.If the product does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions, because improper
adjustment of other controls may result in damage and will often require extensive work
by a VTech authorized technician to restore the product to normal operation.
E.Ifthe product has been droppedand the cabinethas been damaged.
F. If the product exhibits a distinct change in performance.
13. Avoidusing a telephone(other than a cordlesstype) during anelectrical storm. There
may be a remote risk of electric shock from lighting.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
VTECH COMMUNICATIONS INC
SERVICEDEPT.at1-800-595-9511.InCanada,callVTechElectronicsLtdat1-800-267-
7377. SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS

2
Enhanced 2.4GHz Technology -Dual Band transmissioncombines the best of 2.4GHz and
900MHztechnologies,providingenhanced performance over standard cordless telephones.
About Caller Identification (Caller ID)
This product has a Caller ID with Call Waiting feature that works with service from your local
phoneserviceprovider.
CallerIDwithCallWaiting lets you see who’s calling beforeyouanswerthephone,even when
you’reonanother call.
You may need to change your phone service to use this feature. Contact your phone service
providerif:
• You have both Caller ID and Call Waiting, but as separate services (you may need
combinedservice)
• Youhave only CallerID service, oronly Call Waitingservice
• Youdon’t subscribe toany Caller IDor Call Waitingservices.
You can use this product with regular Caller ID service, and you can use this product’s other
featureswithoutsubscribingtoeitherCallerIDorcombinedCallerIDwithCallWaitingservice.
There are fees for Caller ID services, and they may not be available in all areas.
Thisproductcan provide information onlyifboth you and thecallerare in areas offeringCaller
ID service, and if both telephone companies use compatible equipment.
Parts Check List:
1. Base Unit 2.Handset
3.ACPowerAdapter 4.TelephoneLineCord
5. Battery Pack 6. Belt clip
7. Owner’s Manual
To purchase replacement battery packs, call VTech Communications Inc at 1-800-595-
9511. In Canada, call VTech Electronics Ltd at 1-800-267-7377.
BEFORE YOU BEGIN

3
Before You Install
1. Choose a location for the Base near an electrical outlet and a telephone jack.
This phone requires a modular telephone jack and a standard electrical outlet (110v AC)
not controlled by a wall switch. Plug the AC power adaptor into the electrical outlet and
the DC connector to the jack on the bottom of the Base Unit.
2. Install the handset battery pack. Use only battery pack provided or recommended by
VTECH.
a)Remove battery
compartment cover
by pressing on the
indentation and
sliding downward.
b)Align the two holes in the plug with the
socket pins, then snap the plug into
place.
c)Place battery pack in the compartment
with the wires in the lower left corner,
along the bottom of the battery pack.
d)Replace cover by sliding it
up into place.
3. Attach the belt clip to the cordless handset (optional).
To attach To remove
NOTE: Install the Base Unit away from electronic equipment, such as personal computers,
television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture.
INSTALLATION

4
Table/Desk Installation
CONNECT THE POWER CORD
CONNECT THE
TELEPHONE LINE CORD
Standard electrical outlet
Modular telephone jack
4. Chargethehandset battery.
Placethe handset in thebase.Charge the batteryforat least 12hoursthe first time.
5. Checkfordial tone
After the batteries are charged, connect the modular telephone cord between a live phone jack
andthe jack located onthe bottom of theBase Unit. Pick up theHandset and press PHONE.
Youshouldhear a dial tone.
6. Setthedialmode.
If you have touch tone service, the phone is ready to use as soon as the batteries are charged.
If you have dial pulse (rotary) service, you’ll need to change the dial mode.
• PressPROG/CHANonthehandset to enterprogramming mode.
• Press or until the screen displays DIAL MODE:and the currently selected mode.
• PressSELECT.Thecurrentsettingblinks.
• Press to select TONE or PULSE .
• PressSELECT,to savethedisplayed mode.
INSTALLATION

5
General Information
The TeleZapper feature in your VT 2528 is a patented device that helps you eliminate
those annoying telemarketers who call you.
•The TeleZapper feature in your VT 2528 covers all the telephones and
answering machines on one phone line in your home or office.
•Whenever you or your answering machine answers a call, a special tone
is played into the telephone line.
•The tone tells the telemarketer’s predictive dialing computer to take your
number off the list because the computer thinks your number is
“disconnected.”
•When the telemarketer’s hear the tone, their computer immediately hangs
up and removes your phone number from their list of numbers to call
again! Your number will also not be sold to other telemarketers either!
•Other than hearing the tone when you pick up your telephone, the
TeleZapper feature has no other effect on the operation of your
telephones, answering machines, or other services like Caller ID or Call
Waiting.
•When you activate the TeleZapper feature in your VT 2528, you’ll notice
that you get quite a few “hang-ups” where no one is there when you
answer your telephone. Most of the time, this means you’ve “zapped” a
telemarketer! Over a period of a few weeks, you’ll notice that you are
receiving fewer and fewer telemarkerting calls.
•For even more effective screening, let your answering machine pick up.
Programming Instructions
The TeleZapper feature in your VT 2528 has two levels of privacy to help “zap”
computer dialed telemarketing calls. Your VT 2528 is shipped with the BASIC
level of privacy activated, which will help with the majority of telemarketing
calls. At this level, the TeleZapper feature will emit a single tone which is the
first of three (3) tones for the disconnected signal. The ADVANCED level of
privacy will switch the TeleZapper feature to all three tones of the disconnected
signal and will “zap” even more telemarketing calls.
Here are instructions to switch from BASIC to ADVANCED privacy or to
disable the feature.
1. Press PROG/CHAN, then press until the screen displays TELEZAPPER:
BAS.
2. Press SELECT. The current option is flashing.
3. Use or to choose BAS, ADV or OFF.
4. Press SELECT to activate the selected option.
USINGTHETELEZAPPERFEATURE

6
TeleZapper Q&A:
Q. How does the TeleZapper feature work?
A. When the phone is picked up, the TeleZapper feature plays a tone, which tells the
telemarketer’s predictive dialer computer that the number has been disconnected.
The telemarketer’s computer then takes your number off of the list forever and your
number will not be sold to other telemarketing companies! The TeleZapper feature
only “zaps” computerized calling systems that are set to detect disconnected
numbers. This includes virtually all random telemarketers. It will not “zap” other
companies who dial your phone number directly and not through a telemarketing
computer. People using the TeleZapper products typically see an 80% or higher
reduction in calls.
Q. How do I know when I’ve “zapped” a telemarketer?
A. If you answer your telephone and there’s no one there, the odds are that you just
“zapped” one. Quite often you will see the caller ID from such a call is “unavailable.”
After a month, you will notice that you receive fewer and fewer of these calls.
Q. Do I need one for each telephone or telephone jack in my home or office?
A. No. Your VT 2528 with the TeleZapper feature covers ALL telephones connected
to the same line (telephone number). If you have two lines, you need an additional
unit for your other line.
Q. Will it interfere with my computer or fax machine?
A. No. It plays the tone briefly when the line is answered, then goes to “sleep” waiting
for the next call.
Q. Will it interfere with my answering machine?
A. No. This is the best way to use your TeleZapper feature. Let you answering
machine pick up the line, the TeleZapper feature “zaps” the telemarketer, and you
were not bothered at all! You will need to delay your message for about 2 seconds
to allow the tone to play.
Q. I have voicemail from the telephone company. Will it work with this?
A. No. Voicemail works by forwarding your calls to a central location. In order for the
TeleZapper feature to work, the phone in your home must be picked up. If the call
goes to voice mail, the TeleZapper feature will not activate.
USING THE TELEZAPPER FEATURE

7
TELEPHONE OPERATION

8
TELEPHONE OPERATION

9
Handset Ringer Style/Battery Save
You can select from four different handset ringer styles, or turn the ringer off and
extend the battery life.
1Make sure the handset is off.
2Press PROG/CHAN to enter programming mode.
3Press until the screen displays RINGER:.
4Press SELECT The screen displays the current setting.
5Press or to select 11
11
1, 22
22
2, 33
33
3, 44
44
4,or OFFOFF
OFFOFF
OFF. You will hear a sample of each ring.
6Press SELECT to choose the displayed ringer setting.
Temporary Tone Dialing
If you have dial pulse (rotary) service, you can change from dial pulse
to touch tone dialing during a call by pressing *. This is useful if you
need to send touch tone signals for access to telephone banking or
long-distance services.
1 Dial the number.
2 Press *. Buttons pressed after this send touch tone signals.
3 After you hang up, the phone automatically returns to dial pulse (rotary) service.
Headset Jack
You can use this telephone hands-free when you install any VTECH 2.5mm headset,
purchased separately.
Plug the headset into the jack located on the right side of the handset (under the
small rubber flap). Do not force the connection, but make sure the plug fits securely.
TELEPHONE OPERATION

10
Operating Range
This cordless telephone operates within the maximum power allowed by the Federal
Communications Commission (FCC). Even so, this handset and base can commun-
icate over only a certain distance---which can vary withthe locations of the base and
handset, the weather, and the construction of your home or office. For best perfor-
mance, keep the base antenna fully upright.
If you receive a call while you are out of range, the handset might not ring — or
if it does ring, the call might not connect when you press PHONE . Move closer to
the base, then press PHONE to answer the call.
If you move out of range during a phone conversation, you might hear noise or
interference. To improve reception, move closer to the base.
If you move out of range without pressing OFF, your phone will be left “off the
hook.” To hang up properly, walk back into range, periodically pressing OFF .
Display Screen Messages
TELEPHONE OPERATION
Screen Displays: When:
There is a call coming in.
The handset is waiting for dial tone.
The handset is in use.
You have received telephone company voice mail.
The base is paging the handset.
There is a call on hold.
The battery needs to be recharged.

11
This cordless phone can store 10 telephone numbers with names, each up to 16
digits long in memory locations you assign (0-9).
Note: Press OFF at any time to exit memory dial mode.
Store a Number / Name in Memory
1Press PROG/CHAN, then press until the screen displays MEM DIALMEM DIAL
MEM DIALMEM DIAL
MEM DIAL.
2Press MEM. The screen displays ENTER 0-9ENTER 0-9
ENTER 0-9ENTER 0-9
ENTER 0-9.
3Press the key (0-9) for the memory location where you’re storing this entry. If
the selected location is empty, the screen displays ENTER NAMEENTER NAME
ENTER NAMEENTER NAME
ENTER NAME.
Note: If the location is not empty, the current entry is displayed. Press OFF to exit
memory dial mode and start again, or follow the instructions to dial, edit or erase the
current entry.
4Using the chart below, enter up to 15 characters for the name you’re storing
with the number. Use to backspace and make corrections; use to
advance and add a space.
Dial Key: Presses
123456
1
2
3
4
5
6
7
8
9
0
*
#
1
ABC2
DEF3
GHI 4
JKL5
MNO6
PQRS7
TUV8
WXYZ9
0
*
&,-.#
5Whenyou finish enteringthe name,pressSELECT or PROG/CHAN.The screen
displays ENTER NUMBERENTER NUMBER
ENTER NUMBERENTER NUMBER
ENTER NUMBER.
6Enter the telephone number. Use to backspace and make a correction.
Press REDIAL/PAUSE to store a pause in the dialing sequence.
7Press SELECT or PROG/CHAN to store your entry. The screen displays
DISTINCT RING?DISTINCT RING?
DISTINCT RING?DISTINCT RING?
DISTINCT RING? and the current setting.
TELEPHONE MEMORY

12
8Press or to change the setting. Choose Y(for Yes) if you wish the phone
t
o alert you to calls from this number by changing to a distinctive ringing pattern
after the first ring. Choose N(for NO) for a normal ringing pattern.
9Press SELECT or PROGRAM to confirm your selection. If you choose Y, a DD
DD
D
will be displayed with the directory entry.
Note: When memory is full the screen displays MEMORY FULL, an error tone
sounds, and you will not be able to store a new number until you delete a stored
number.
Edit a Number/Name Stored in Memory
1Press MEM . The screen displays ENTER 0-9.
2Press the memory location key of the entry you wish to edit.
3When the screen displays the number you want to edit, press SELECT. Then
press or until EDIT flashes.
4PressSELECT.The screen displaysthe name andnumber. The flashingcursor
appears at the end of the name. Use , and the dial pad keys to edit the
name. Press SELECT to move on to edit the number. Press SELECT to move
on to edit the Distinctive Ring setting.
5Press SELECT to save the edited information.
Delete a Number/Name Stored in Memory
1Press MEM . The screen displays ENTER 0-9.
2Press the memory location key of the entry you wish to delete.
3When the screen displays the number you want to delete, press SELECT. Then
press or until ERASE flashes.
4Press SELECT. The screen displays ERASE NO YES and the number.
5Press or until YES flashes.
6PressSELECT.
Dial a Memory Number
1Press MEM . The screen displays ENTER 0-9.
2Press the memory location key of the entry you wish to dail.
3When the screen displays the number you want to dial, press SELECT. Then
press or until DIAL flashes.
4Press SELECT. The phone automatically dials the number.
TELEPHONE MEMORY

13
This cordless phone can store 40 telephone numbers with names, each up to 16
digits long. Entries are stored alphabetically. For consistency withCaller ID entries,
you may wish to enter last names first.
Note: Press OFF at any time to exit directory.
Store a Number/Name in the Directory
1Press PROG/CHAN . The screen displays DIRECTORY .
2Press SELECT . The screen displays ENTER NAME .
3Using the chart below, enter up to 15 characters for the name you’re storing with
the number. Use to backspace and make corrections; use to advance and
add a space.
Dial Key: Presses
123456
1
2
3
4
5
6
7
8
9
0
*
#
1
ABC2
DEF3
GHI 4
JKL5
MNO6
PQRS7
TUV8
WXYZ9
0
*
&,-.#
4When you finish entering the name, press SELECT or PROG/CHAN. The screen
displays ENTER NUMBER .
5Enter the telephone number. Use to backspace and make a correction. Press
REDIAL/PAUSE to store a pause in the dialing sequence.
-OR-
Press REDIAL/PAUSE to display the last number dialed from this phone.
6Press SELECT or PROG/CHAN. The screen displays DISTINCT RING? and
the current setting.
7Press or to change the setting. Choose Y(for Yes) if you wish the phone to
alert you to calls from this number by changing to a distinctive ringing pattern
after the first ring. Choose N(for NO) for a normal ringing pattern.
TELEPHONE DIRECTORY

14
8 Press SELECT or PROG/CHAN to confirm your selection. If you chose Y, a Dwill
be displayed with the directory entry.
Note: When memory is full the screen displays MEMORY FULL , an error tone sounds,
and you will not be able to store a new number until you delete a stored number.
Edit a Number/Name Stored in the Directory
1 Press ( ). The screen displays DIRECTORY .
2 Press or to scroll alphabetically through entries stored in memory
-OR-
Press the dial pad key for the first letter of the entry you want to edit.
3 When the screen displays the number you want to edit, press SELECT . Then
press or until EDIT flashes.
4 Press SELECT. The screen displays the name and number. The flashing cursor
appears at the end of the name. Use , and the dial pad keys to edit the
name. Press SELECT to move on to edit the number. Press SELECT to move to
edit the Distinctive Ring setting.
5 Press SELECT to save the edited information.
Delete a Number/Name Stored in the Directory
1 Press ( ). The screen displays DIRECTORY.
2 Press or to scroll alphabetically through entries stored in memory
-OR-
Press the dial pad key for the first letter of the entry you want to delete.
3 When the screen displays the number you want to delete, press SELECT . Then
press or until ERASE flashes.
4 Press SELECT. The screen displays ERASE NO YES and the number. The
current choice flashes.
5 Press or until YES flashes.
6 Press SELECT. You’ll hear a series of beeps confirming the deletion.
Dial a Number from the Directory
1 Press ( ). The screen displays DIRECTORY.
2 Press or to scroll alphabetically through entries stored in memory
-OR-
Press the dial pad key for the first letter of the entry you want to dial.
3 When the screen displays the number you want to dial, press SELECT. Then
press or until DIAL flashes.
4 Press SELECT. The phone automatically dials the number.
TELEPHONE DIRECTORY

15
CALLER ID OPERATION
About Call History
This phone assigns each incoming call a number from 1 to 99. The most recent call
will have the highest number. When the memory is full, the oldest call information is
deleted to make room for new incoming call information.
For each call that comes in, the screen displays the following information between the
first and second rings:
• Your caller’s name (15 letters are sent by your telephone company)
• The caller’s area code and telephone number
• The time and date of the call
• The position of the call in call history.
If you answer a call before the information appears on the screen, it will not be in the
call history.
Note: Press OFF at any time to exit call history.
Review Call History
The screen displays call information for about 15 seconds after it has been received.
1 Press (CID) to view call history.
2 Use or to scroll through records in call history.
Delete Records from Call History
Delete a Specific Call
1 Locate the record you want to delete from call history.
2 Press SELECT, then press or until ERASE flashes.
3 Press SELECT. The screen displays ERASE NO YES ALL and the phone
number. The current choice flashes.
4 Press or until YES flashes.
5 Press SELECT. You’ll hear a series of beeps confirming the deletion.
Delete All Calls
1 While viewing call history, press SELECT,then press or untilERASE flashes.
2 Press SELECT. The screen displays ERASE NO YES ALL and the phone
number. The current choice flashes.
3 Press or untilALL flashes,then press SELECT. The screendisplaysERASE
ALL NO YES. The current choice flashes.

16
4 Press or until YES flashes.
5 Press SELECT. You will hear a series of beeps confirming the deletion.
Dial a Displayed Number
1 Locatethe record incall history thatyou want to dial.
2 If you wish to change how the number is dialed, press #.
Thescreendisplaysanyalternatedialing sequencesavailableforthiscall(areacode
+number; 1+ areacode + number;1+ number;number only).
3 Press SELECT, then press or until DIAL flashes.
The phone number will be displayed in the format it was received.
4 Press SELECT when the number is correctly displayed for dialing.
Store a Call History Record in the Directory
1Locate the record in call history you want to store in memory.
2If you wish to change how the number is stored, press #. The screen displays
any alternate dialing sequences available for this call (area code + number; 1 +
area code + number; 1+ number; number only).
3Press SELECT, then press or until PGM flashes.
The phone number will be displayed in the format it was received.
4Press SELECT four times to store the call record in memory. You’ll hear a beep
confirming that the name number were stored.
DisplayScreen Messages
Screen Displays: When:
The other party is blocking name information.
The other party is blocking name and number
information.
Your phone company is unable to receive information
about this caller s name.
Your phone company is unable to receive information
about this caller s name and number.
CALLER ID OPERATION

17
Charge the Handset Battery Pack
•This battery should remain charged up to six days with the ringer turned on and
up to 12 days with the ringer off. A fully charged battery provides an average talk
time of about six hours.
•The battery pack needs charging when:
— A new battery is installed in the handset.
— The phone beeps twice every 5 seconds.
— The screen displays BATTERY LOW and the low battery icon.
•Place the handset in the base so the CHARGING light turns on. The battery pack
is typically fully charged in eight hours.
•You can keep the battery fully charged by returning the handset to the base after
each use.
•If you repeatedly get a low battery indicator, even after charging overnight, the
battery should be replaced. Use VTECH Battery.
CAUTION: To reduce the risk of fire or injury to persons or damage to
the telephone, read and follow these instructions carefully:
Charge the battery provided with or identified for use with this product
only in accordance with the instructions and limitations specified in this
User’s Manual.
Replacing the Handset Battery Pack
1 Remove the battery compartment cover on the handset by pressing on the
indentation and sliding the cover downward.
2 Lift out the old battery pack and disconnect.
3 Align the two holes in the new battery pack’s plug with the socket pins, and snap
the plug into place. Place the battery pack in the compartment with the wires in
the lower left corner, along the bottom of the battery pack.
4 Replace the cover by sliding it up into place.
5 Thenew battery pack mustbe charged before usingthephone. Place the handset
in the base and allow it to charge for at least 12 hours the first charge. The
telephone might operate before that, but for best performance, let the battery
pack charge fully.
BATTERIES

18
If you have difficulty operating this phone, try the suggestions below.
For Customer Service, call 1-800-595-9511. Please retain your receipt as your proof
of purchase
If the phone doesn’t work at all, check these items first:
•Makesurethe AC adapter is plugged into an outletnotcontrolled by a wall switch.
•Make sure the telephone line cord is plugged firmly into the base unit and the
modular jack.
•Make sure the base antenna is fully upright.
•If the handset does not beep when you press PHONE, the battery might need
charging.
•Make sure the battery pack is installed correctly.
•If you have dial pulse (rotary) service on your phone line, make sure the dial
mode is set to dial pulse (see INSTALLATION).
•Microwave appliances may cause interference with this phone. If you experience
interference, move away from the microwave
If the above suggestions don’t solve the problem, try re-initializing the handset
and base:
1Disconnect the power to the base.
2Remove the handset battery pack.
3Wait a few minutes.
4Connect the power to the base.
5Insert the handset battery pack.
6Put the handset in the base to re-initialize.
If you hear a two-beep signal when you try to use the handset:
•You might be out of range. Move closer to the base and try again.
•If moving closer to the base doesn’t help, try following the directions above for
re-initializing the handset and base.
If the phone does not ring when you receive a call:
•Make sure the handset ringer is on.
•Make sure the telephone line cord is connected firmly to the base and the
telephone jack.
•Make sure the AC adapter is plugged firmly into an outlet not controlled by a
wall switch.
•You might be too far from the base; move closer.
•You might have too many extension phones on your telephone line to allow all
of them to ring. Try unplugging some of them.
IN CASE OF DIFFICULTY

19
IN CASE OF DIFFICULTY
If you hear noise or interference when using the phone:
• Make sure the base antenna is fully upright.
• You may be out of range. Move closer to the base.
• Pressand releasePROG/CHAN tochange toanother ofthe 30channels available.
If noise is exceptionally loud, move closer to the base before changing channels.
• Household appliances plugged into the same circuit as the base can sometimes
cause interference. Try moving the appliance or the base to another outlet.
• Usingthe handsetnear householdappliances (microwaves, computers,television,
stereos, etc.) can sometimes cause interference. Move away from appliances
while using the handset.
• The layout of your home or office might be limiting the operating range. Try
moving the base to another location, preferably on an upper floor.
• Ifthe buttonsdon’t work,try placingthehandset inthe basefor atleast 15 seconds.
If you hear other calls while using your phone:
• Press PROG/CHAN to change to another channel.
• Disconnect the base from the modular jack and plug in a corded telephone. If you
still hear other calls, the problem is probably in your wiring or local service. Call
your local telephone service company.
If you lose a call after changing channels:
You were probably almost out of range. Move closer to the base before changing
channels. Before placing another call, set the handset in the base for at least 15
seconds.
If you are unable to operate special telephone services or other equipment
requiring touch tone signals:
If you have dial pulse (rotary) service, follow the directions under “Temporary Tone
Dialing” in the TELEPHONE OPERATION section of this manual.
If the MESSAGE light on the base does not go off even after you’ve listened to
voice mail messages:
1 PressPROG/CHAN.
2 Press until the screen displays MESSAGES WAITING .
3 Press SELECT. The screen displays LIGHTS OFF:YES .
4 Press SELECT again to turn off the MESSAGE light on base.

20
Taking Care Of Your Telephone
Your GIGAPHONE cordless telephone contains sophisticated electronic parts, so it
must be treated with care.
Avoid rough treatment
Place the Handset down gently. Save the original packing materials to protect your
telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the Handset outdoors in the
rain, or handle it with wet hands. Do not install your Base Unit near a sink, bath-
tub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equip-
ment.
For your own safety, use caution when using electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many
years. Clean it only with a soft cloth slightly dampened with water or a mild soap. Do
not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are
wet or standing in water. If your Base Unit should fall into water, DO NOT
RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE
CORDS FROM THE WALL. Then pull the unit out by the unplugged cords.
MAINTENANCE