V-tech VT9105 User manual

TELEPHONE LINE
CORD
WALL MOUNT BRACKET
BASE UNIT
HANDSET
AC ADAPTER
BATTERY PACK
Parts Check List:
1. Handset
2. Base Unit
3. Telephone line cord
4. AC adapter
5. Battery Pack
6. Wall mounting bracket
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
1. Remove the battery case by pressing on the
ridgedlines and slidingdownward.
2. Discard the old battery pack. Don't put the old
battery pack in a trash compactor or a fire - it
could burst.
Service at 1-800-595-9511. Opening or
removingcabinetpartsotherthanspecified
access doors may expose you to
dangerousvoltages orotherrisks. Incorrect
reassembling can cause electric shock
whenthe appliance is subsequently used.
11. Donotoverloadwalloutletsandextension
cords as this can result in the risk of fire or
electricshock.
12. Unplug this productfromthewall outlet:
a) Whenthe power supply cord or plug is
damagedorfrayed.
b) Ifliquid hasbeenspilledintothe product.
c) Ifthe product hasbeenexposed to rain
orwater.
d) Ifthe productdoes notoperatenormally
byfollowingthe operating instructions.
Adjust only those controls that are
covered by the operating instructions
becauseimproperadjustment of other
controlsmayresult in damage and will
oftenrequireextensive work to restore
theproduct to normal operation.
e) If the product has been dropped and
thecabinet has been damaged.
f) If theproductexhibits a distinctchange
inperformance.
13. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shockfrom lighting.
14. Do not use the telephone to report a gas
leakinthevicinity of the leak.
SAVETHESE INSTRUCTIONS
When using your telephone equipment, basic
safetyprecautions should always befollowedto
reduce the risk of fire, electric shock and injury
topersons, including thefollowing:
1. Readandunderstandall instructions.
2. Followallwarningsandinstructions marked
ontheproduct.
3. Unplugthisproductfromthewalloutletbefore
cleaning.Donot useliquidcleanersoraerosol
cleaners.Usea damp cloth for cleaning.
4. Do not use this product near water (for
example, near a bath tub, kitchen sink, or
swimmingpool).
5. Donotplace thisproductonanunstable cart,
stand,or table.The productmayfall,causing
seriousdamageto the product.
6. Slots and openings in the cabinet and the
back or bottom are provided for ventilation.
Toprotectitfromoverheating,theseopenings
must not be blocked by placing the product
onthe bed,sofa, rug,orother similarsurface.
Thisproduct should never be placednearor
over a radiator or heat register.This product
shouldnotbe placed in a built-in-installation
whereproper ventilation is not provided.
7. This product should be operated only from
the type of power source indicated on the
markinglabel.Ifyou are not sure of the type
of power supply to your home, consult your
dealerorlocalpowercompany.
8. Do not allow anything to rest on the power
cord. Do not locate this product where the
cordwill beabusedby persons walkingon it.
9. Never push objects of any kind into this
product through cabinet slots as they may
touchdangerousvoltagepointsorshortout
partsthatcouldresultinariskoffireorelectric
shock. Never spill liquid of any kind on the
product.
10.To reduce the risk of electric shock, do not
disassemblethis product. If service orrepair
work is required, contact VTech Customer
IMPORTANT:Donotdisposeof this battery
in household garbage. For
information on recycling or
properdisposal, consult your
localsolid waste collection or
disposalorganization.
3.Place the new battery pack in the battery
compartment. Make sure the metal
contacts on the underside of the battery
are aligned with charging contacts in
battery compartment.
4.Replacethe battery cover by sliding itinto
place.
5.The new battery pack must be charged
before using your telephone. Place the
handset in the cradle of the base unit to
allowit to chargefor 24 hours. Maximum
batterylifebetweenchargesis more than
5hours of continuous talk time or 4 days
of standby.
CAUTION: To reduce the Risk of Fire or
Injury to Persons, Read and
Follow these instructions:
1. Use only VTECH battery.
2. Do not open or mutilate the battery.
Released electrolyte is corrosive and
may cause damage to the eyes or skin.
It may be toxic if swallowed.
VTECH
1
3
2
3. Exercise care in handling batteries in
order not to short the battery with
conducting materials such as rings,
bracelets, and keys. The battery or
conductor may overheat and cause
burns.
4. Do not dispose of the battery in a fire.
The cell may explode.
REPLACINGTHE HANDSET BATTERIES
VT 9108/9105
USERS MANUAL
900MHz CORDLESS TELEPHONE
VTECH COMMUNICATIONS LTD.
IMPORTANT
BEFORE USING YOUR NEW
PHONE, WE STRONGLY
RECOMMEND YOU READ THIS
MANUAL THOROUGHLY.
Print in China 91-5050-10-00
ISSUE 0

wallboard
wooden
stud
PULSE
TELEPHONE
WALL JACK
AC ELECTRICAL
OUTLET
TONE PULSE
TONE
GETTING STARTED
HANDSET FEATURES
WALL MOUNTING
Setting UpYour VT 9108/VT 9105
1. Choose an area near an electrical outlet
and a telephone wall jack.
2. Connect the telephone line cord. Insert
one end of the telephone line cord into
the jack at the rear of the base unit. Plug
the other end into a telephone wall jack.
Make sure the plugs snap securely into
place.
3. Plug the AC power adapter into an
electrical outlet and the DC connector to
the back of the base unit.
CAUTION:Use only the AC adapter
shipped with your VT 9108/VT
9105. This is a Class 2 AC
adapter, specifically designedfor
use with the VT 9108/VT 9105.
NOTE: Connect power to the base unit
before placing the handset in the
cradle.
4. SettheTONE/PULSEswitchonthebase
unit. If you have touch tone service on
your phone line, set the switch to TONE.
If you have rotary service, set the switch
to PULSE.
5. CHARGE THE HANDSET BATTERIES
BEFORE USE. The batteries recharge
automatically whenever the handset is
in the base unit cradle. The batteries
must be charged for 24 hours before
using your phone for the first time.
6. CHECK FOR A DIAL TONE. After the
batteries are charged, pick up the
handset and press the PHONE key.The
IN USE indicator should light up, and
you should hear a dial tone. If not, see
IN CASE OF DIFFICULTY.
CAUTION:
1. Never install telephone wiring during a
lightning storm.
2. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
3.Never touch uninsulatedtelephone wires
or terminals unless the telephone line
has been disconnected at the network
interface.
4. Use caution when installing or modifying
telephone lines.
1.Choosea spot near an electrical outlet
and a telephone jack.Your phone
requires a modular telephone jack and
a standard electrical outlet (120V AC).
The power cord is six feet long; make
sure there is an electrical outlet within
reach of the base.The outlet should not
be controlled by a wall switch. If the
switch is ever turned off, the phone will
not operate.
2.Positionthe wall mount adapter on the
base. Lineupthe tabs on the wallmount
adapter with the holes on the bottom of
the base. Snap the wall mount adapter
firmly in place.
3.Mount the base on the wall. Position
the base so the mounting studs will fit
into the holes on the bottom of the base.
Position the power cord to extend down
the wall the phone is to be mounted on.
Slide the base down on the mounting
studs until it locks into place.
MEM,Number Button (0-9).
PROG KEY
* Press PROG key to enter PROGRAM
mode. See Programming Speed Dial
Numbers for more details.
REDIAL KEY
* When you hear the dial tone, pressing
the REDIAL key will dial out the last
number that was called on your phone.
* It can also be used to store the last
number dialed into the speed dial
memory.See Storing a Redial Number
into Speed Dial for details.
TONE/ KEY
* In PULSE dialing mode, this key is used
to switch to Temporary TONE dialing
mode.
VOLUME SWITCH
* Thereare three volume setting:Low,
Medium and High.
BATTERY LOWWARNING BEEP
* Uponpressing PHONE, theHandset will
emittwobeepstoindicatethatthebattery
packneeds to be recharged.
IN USE LED
* The IN USE LED lights when the phone
line is being used by the handset.
* It flashes in cadence with an incoming
ring.
* It flashes quickly during PROG mode.
PHONE KEY/ FLASH KEY
* Press the PHONE key to make a call.
* If you are currently on a call, pressing
PHONE flashes the line.This would be
used with a feature like call waiting to
answer your second call.
CHAN KEY
* Pressing the CHAN key when the
handset is in use will activate a channel
change to the next free channel.
* This is used if you are experiencing
noise or interference on the current
channel.
OFF KEY
* Press the OFF key to exit all modes of
operation.
MEM KEY
* Press the MEM key to enter MEMORY
mode.
* The sequence for dialing out a speed
dial number in memory is: PHONE,
4.Connect the telephone cord. The
telephone line cord has a snap-in plug
at each end. Insert one of the plugs into
thejackon the bottom ofthebase. Insert
the other end of the plug into the wall
jack.
5.Connect the power cord. Plug the DC
connector into the DC jack at the rear of
the base unit. Plug the AC power
adapter into an electrical outlet.
6.Set the dial mode switch on the base
unit. If you have touch tone service on
your phone line, set the switch toTONE.
If you have rotary service, set the switch
to PULSE.
45
7
CHARGING LED
* The CHARGE LED illuminates steadily when
the handset is in the base cradle to indicate
that the handset battery is being charged.
PAGE KEY
* Press the PAGE key to page the
handset.
* Press it a second time to cancel a
page.
* The base will ring the handset 4
times before ending the page
automatically.
* The handset can also cancel the
page by pressing the OFF key.
BASE UNIT FEATURES
TONE/PULSE SWITCH
* This switch will switch the phone between
TONE dialing and PULSE dialing.
REPLACEMENT BATTERY ORDER FORM
ForVTECH9108/9105 CordlessTelephone
Name: Address:
City: State: Zip:
daytime phone Number: ( )
ORDER INFORMATION
For Model VT 9108/VT 9105
(QTY.) Batteries @$19.95 each............................$
$5.95 Shipping & Handling Per Battery Ordered....................................................$
METHOD OF PAYMENT: DO NOT SEND CASH
CHECK MONEY ORDER VISA MASTERCARD AMERICAN EXPRESS
CREDIT CARD# EXP. DATE
CARDHOLDERÕS SIGNATURE
PLACEORDER FORMANDPAYMENT IN ENVELOPE AND SENDTO:
VTECHCOMMUNICATIONS
8770SWNIMBUS AVENUE
BEAVERTON,OREGON 97008-7195 USA
YOU MAY ALSO ORDER BY PHONE.CALL 1-800-595-9511
CUT
6
CHAN KEY
OFF KEY
PROG KEY REDIAL KEY
MEM KEY
VOLUME SWITCH
PHONE KEY
IN USE / LOW BATT LED
TONE/ KEY
CUT

IN CASE OF DIFFICULTY
Disconnecting
To end a call, either place the handset back
in the base, or press OFF on the handset.
Changing Channels
If you notice interference when using your
handset, press CHAN to switch to a clear
channel.Thisfunctionis only available when
you are on a call.
TemporaryTone
If you have a rotary (dial-pulse) telephone
service, (TONE/PULSE switch is set to
PULSE), this feature allows you to enter
special codes and tones to operate
answering machines, use electronic
banking services, calling cards, or other
special services.
First, dial the call normally. Then activate
the Temporary Tone feature by pressing
TONE (the key). You can then press the
numbers or symbols you need, and your
phone will send the proper signals.
To end the call, press OFF or place the
handset back in the base. The phone will
automatically go back to rotary (dial-pulse)
service.
ProgrammingThe RingerType
The handset ringer is capable of four
differenttypes ofringing tones.Thefollowing
sections detail how to change the different
tonesand to turnoff a ringer onthe handset.
To program, the handset must be OFF.
To select a different ringer type do the
following:
* Press PROG
* Press the #key.
* Press a key 1..4 to select a ringer type.
* Press the OFF key to exit.
Turning OffThe Ringer
To turn off the ringer on the handset, do the
following:
IMPORTANT:
Whenever the handset batteries are
removed, the handset must be reinitialized
on the base unit cradle after the batteries
are replaced.The IN USE LED on the base
unit will flash during the initialization.
Making Calls
Pick up the handset and press PHONE.
When you hear a dial tone, dial the number.
The indicator for IN USE (on the handset)
will light.
If you make a mistake when dialing, press
OFF to hang up, then press PHONE to get
the dial tone again.
You must always press PHONE before you
can dial a call on the handset.
* Press PROG
* Press the #key
* Press 5to turn off the ringer
* Press the OFF key to exit
* To turn the ringer on again, see
Programming the RingerType.
CheckingThe Ringer
To check the ringer which is currently
programmed, do the following:
* Press PROG
* Press the #key
* Press 0
* Press the OFF key to exit
Memory Dialing
The
VT 9108/VT 9105 can store up to 10
different phone numbers that you can dial
just by pressing phone, MEM and one of
the number keys (0-9).
Programming Speed Dial Numbers
The handset must be OFF.
1. Press PROG.The IN USE LED will blink
to indicate that you are in the
programming mode.
2. Pressthe number of thememory location
you wish to store the number in (0-9).
3. Using the dial pad, dial the number you
want to store. The number can be up to
16 digits long. The number can be
entered manually or by using REDIAL.
4. Press MEM to store the phone number
to the key you selected.
The phone now exits PROG mode and you
willheara long confirmation beep.
Speed Number Dialing
1. Press PHONE to get a dial tone.
2. Press MEM and the memory location
number key (0-9).
For example, to dial the number you
assigned to key '8', you would press
PHONE, MEM, 8.
OPERATING INSTRUCTIONS
If you have difficulty operating your phone, the
suggestionsbelowshouldsolvetheproblem.Ifyoustill
have difficulty after trying these suggestions,
In the US call:
VTECH Communications at
1-800-595-9511.
In Canada Call:
VTECH Electronics at
1-800-267-7377.
THE PHONE DOESN'T WORK AT ALL.
* Make sure the power cord is plugged in.
* Make sure the telephone line cord is plugged firmly
into the base unit and the telephone wall jack.
* Make sure the batteries are properly charged. If the
handset make two beeps, the battery needs
charging. If the IN USE indicators do not light when
you press PHONE, you must charge the batteries.
* If you recently installed a new battery pack, make
sure it is installed correctly.
NO DIAL TONE.
* First check all the suggestions above.
* If you still don't hear a dial tone, disconnect the base
unit from the telephone jack and connect a different
phone.Ifthereisnodialtone on thatphoneeither,the
problem is in your wiring or local service. Call your
local telephone company.
YOU GET NOISE, STATIC, OR A WEAK SIGNAL
EVEN WHEN YOU'RE NEAR THE BASE UNIT.
* Place the handset in the base momentarily to re-set
the security code.Then press PHONE to get a line.
Household appliances plugged into the same circuit
as the base unit can sometimes cause interference.
Try moving the appliance or the base unit to another
outlet.
YOU GET NOISE, STATIC, OR A WEAK SIGNAL
WHEN YOU'RE AWAY FROM THE BASE UNIT.
* You may be out of range.Either move closer to the
base, or relocate the base unit.
* The layout of your home may be limiting the range.
Try moving the base unit to the second or third floor,
or to some other location.
To Change orReplacea SpeedDialNumber
Tochange or replace astored numberin speed
dial memory simply enter the new number and
storeitinthememorylocationyouwishtochange.
For example, to change the number stored in
memoryposition7to555-1111,youwouldpress
PROG,7,555-1111,MEM.
StoringPausesin Memory
Toinsertapauseina phonenumber,pressand
hold the number before the position where the
pauseistobeinserted.Holdthenumberkeydown
until it beeps twice.The pause is 2 seconds in
length.Forlongerpauses,pressandholdthekey
untilitbeepsthreeorfourtimes.Eachadditional
beepindicatesanadditional2secondpause.
If your phone is connected to a PBX you can
storethePBXaccessnumberandapausebefore
the phone number. For example, to store 9-
PAUSE-555-1234 in memory location 8 do the
following:
1. Press PROG
OPERATING INSTRUCTIONS
Answering Calls
When an incoming call is ringing, the IN
USE LED on the handset will flash. To
make sure your phone rings when the
handsetisawayfromthebase,pleasekeep
the base antenna in the upright position.
To answer a call when the handset is in
the base, just pick up the handset.
To answer a call when the handset is away
from the base, just press any key on the
handset (except OFF). This is very useful
in a dark environment; you do not have to
fumble around looking for the PHONE key
to answer the call.
2.Press8
3.Pressandhold 9untilitbeepsatleasttwice.
4.Dial555-1234
5.PressMEM
Using REDIAL
To REDIAL the last number you called, press
PHONE then press REDIAL.The phone will
automaticallydialthenumber.
StoringaRedialNumber intoSpeed Dial
Tostorethelastnumberyoudialedasaregular
Speed Dial number, press PROG, a number
key(0-9),REDIAL,MEM.
ThePageFeature
From the base unit, press PAGE to signal the
person at the handset.To end the page at the
base, press PAGE again. To end the page at
thehandset,pressOFF.
Thisfeatureisalsousefulifyouhavemisplaced
thehandset.
OPERATING INSTRUCTIONS
THE HANDSET DOES NOT RING WHEN YOU
RECEIVE A CALL.
* Ensure that the ringer is turned on.
* Makesurethetelephonelinecordispluggedfirmly
into the base unit and the telephone jack. Make
sure the power cord is plugged in.
* You may be too far from the base unit.
* You may have too many extension phones on
your telephone line to allow all of them to ring.Try
unplugging some of the other phones.
YOUR CALLER FADES IN AND OUT.
You may be nearly out of range. Move closer, or
relocate the base.
YOU HEAR OTHER CALLS WHILE USING
YOUR PHONE.
* Replace the handset in the base cradle, wait a
few moments and try again.
* Disconnect your base unit from the telephone
jack, and plug in a regular telephone. If you still
hear other calls, the problem is probably in your
wiring or local service. Call your local telephone
company.
YOU HEAR NOISE IN THE HANDSET, AND
NONE OF THE KEYS OR BUTTONS WORK.
* Make sure the power cord is plugged in.
* Yourbaseunitand handsetmaynotbeoperating
on the same channel or security code. Place the
handsetinthecradleforafewmomentstoreload
the security code and reset the channel.
COMMON CURE FOR ELECTRONIC
EQUIPMENT
Electronics, like people, can sometimes get
confused.Iftheunitdoesnotseemtoberesponding
normally, then try putting the handset in the cradle
to re-initialize the unit. If it still does not seem to
respond, perform the following steps (in the order
listed):
1. Disconnect the power to the base.
2. Disconnect the handset battery.
3. Wait a few minutes.
4. Connect power to the base.
5. Connect the handset battery.
6. Put the handset in the base to re-initialize.
8 9
11
CHARGING LED
IN USE LED / LOW BATT
VOLUME SWITCH OFF KEY
PHONE KEY CHAN KEY
REDIAL KEY
MEM KEY
PAGE KEY
PROG KEY
TONE/ KEY
10
The RBRC Seal on the
(easily removable)
nickel-cadmium battery
(contained in our product) indicates that
VTech Communications,INC. is voluntarily
participatinginanindustryprogramtocollect
andrecyclethesebatteriesattheendof their
usefullives,whentaken out of servicewithin
theUnitedStates and Canada.
TheRBRC programprovidesaconvenient
alternative to placing used nickel-cadmium
batteries into the trash or municipal
waste,whichmaybeillegalinyourareas.
VTech’s payments to RBRC make it easy
for you to drop off the spent battery at local
retailersparticipatingintheRBRC program
The RBRC
TM
Seal
oratauthorizedVTechproduct service
centers.Pleasecall
1-800-8-BATTERYTM forinformationon
Ni-Cdbatteryrecyclingand disposal bans
restrictionsinyourarea.VTech’sinvolvement
inthis programispartofitscommitment to
protectingourenvironment and conserving
naturalresources.
R
Removethe nickel-cadmiumbatterypack
by pressing on the lock knob and sliding
downwardasmentioned on this page.
RBRC is a registered trademark of
Rechargeable Battery Recycling
Corporation.
R
R
R

MAINTENANCE
FCC AND IC REGULATIONS
This equipment complies with Parts 15 and 68
of the Federal Communications Commission
(FCC) rules for the United States. It also
complies with regulations RSS-210 and CS-
03 of Industry Canada (IC).
A label is located on the underside of the base
unit containing either the FCC registration
number and Ringer Equivalence Number
(REN) or the IC registration number and Load
Number.You must, upon request, provide this
information to your local telephone company.
This equipment is compatible with inductively
coupled hearing aids.
FCCPart 15
Warning:Changes or modifications to this unit
notexpresslyapprovedbythe party
responsible for compliance could
void the user's authority to operate
the equipment.
The equipment has been tested and found to
comply with part 15 of the FCC rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequencyenergy and, if notinstalled and used
inaccordance with the instructions, maycause
harmful interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try and correct the interference
by one or more of the following measures:
WARRANTY STATEMENT
TAKING CARE OFYOURTELEPHONE
Your VT9108/VT 9105 cordlesstelephone
containssophisticated electronic partsso
itmust be treatedwith care.
Avoid rough treatment
Place the handset down gently. Save the
original packing materials to protect your
telephone if you ever need to ship it.
Avoid Water
Your telephone can be damaged if it gets
wet. Do not use the handset outdoors in
the rain, or handle it with wet hands. Do
not install your base unit near a sink,
bathtub or shower.
Remember that electrical appliances can
cause serious injury if used when you
are wet or standing in water. If your base
unit should fall into water, DO NOT
RETRIEVE IT UNTILYOU UNPLUGTHE
POWER CORD ANDTELEPHONE LINE
CORDS FROMTHEWALL . Thenpull the
unit out by the unplugged cords.
Electrical Storms
Electrical storms can sometimes cause
power surges harmful to electronic
equipment.
For your own safety, use caution when
using electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic
casing that should retain its luster for
manyyears. Clean it only witha soft cloth
slightly dampened with water or a mild
soap. Do not use excess water or
cleaning solvents of any kind.
WHAT DOES OUR WARRANTY COVER?
* Any defect in material or workmanship.
FOR HOW LONG AFTER THE ORIGINAL PURCHASE?
* OneYear.
WHAT WILL VTECH DO?
* At our option, repair or replace your unit.
HOW DO I SEND MY UNIT, IN OR OUT OF WARRANTY?
* Call VTECH Communications customer service for Return Authorization at:
1-800-595-9511
* Properly pack your unit. Include any cables & accessories which were originally provided
with the product. We recommend using the original carton and packing materials.
* Include in the package a copy of the sales receipt or other evidence of date of original
purchase (if the unit was purchased within the last twelve months.)
* Print your name and address, along with a description of the defect, and include this in
the package.
* Include payment for any service or repair not covered by the warranty, as determined by
VTECH Communications.
* In the US, ship the unit via UPS Insured, or equivalent to:
VTECH COMMUNICATIONS
8770 SW NIMBUS AVENUE
BEAVERTON, OREGON 97008
VTECH Communications assumes no responsibility for units sent without prior Return Authorization.
WHAT DOES OUR WARRANTY NOT COVER?
* Batteries
* Damage from misuse, neglect, or acts of nature (lightning, floods, power surges. etc.)
* Products which may have been modified or incorporated into other products
* Products purchased outside the USA
* Products serviced by the owner or a service facility not expressly authorized by VTECH
Communications
* Products purchased more than 12 months from current date
HOW DOES STATE LAW RELATE TO THIS WARRANTY?
* This warranty gives you specific rights.You may also have other rights which vary from
state to state.
IF YOU PURCHASED YOUR TELEPHONE IN CANADA
Please call: 1-800-267-7377
Ship to: VTECH ELECTRONICS
200-7671 ALDERBRIDGE WAY
RICHMOND, BC V6X 1Z9
IC (Industry Canada)
This telephone is registered for use in
Canada.
Notice:The Industry Canada label
identifiescertifiedequipment.This
certification means that the
equipment meets certain
telecommunications network,
protective, operational and safety
requirements. Industry Canada
does not guarantee the
equipmentwilloperate totheuser’s
satisfaction.
Before installing this equipment, users
should ensure that it is permissible to be
connected to the facilities of the local
telecommunications company.The
equipment must also be installed using an
acceptable method of connections. The
customer should be aware that compliance
with the above conditions may not prevent
degradation of service in situations.
Repairs to certified equipment should be
made by an authorized Canadian
maintenance facility designated by the
supplier. Any repairs or alterations made
bythe user tothis equipment, orequipment
malfunctions, may give the
telecommunications company cause to
request the user to disconnect the
equipment.
Users should ensure for their own
protection that the electrical ground
connections of the power utility, telephone
lines and internal metallic water pipe
system, if present, are connected together.
FCC AND IC REGULATIONS
* Reorientorrelocatethereceivingantenna.
* Increase the separation between the
equipment and receiver.
* Connect the equipment into an outlet or on a
circuitdifferent fromthattowhichthereceiver
is connected.
* Consult the dealer or an experienced radio/
TV technician for help.
FCCPart 68
The FCC requires that you connect your
cordless telephone to the nationwide telephone
network through a modular telephone jack
(USOC RJ11C or RJ11W).
Your telephone company may discontinue your
service if your equipment causes harm to the
telephone network. They will notify you in
advance of disconnection, if possible. During
notification, you will be informed of your right to
file a complaint with the FCC.
Ifit is determined thatyourtelephoneequipment
ismalfunctioning,theFCC requires that it not be
used and that it be unplugged from the modular
jack until the problem has been corrected.
Repairs to this telephone equipment can only
be made by the manufacturer or its authorized
agents or by others who may be authorized by
the FCC. For repair procedures, follow the
instructions outlined under the VTECH Limited
Warranty.
The REN is useful in determining the number of
devices you may connect to your telephone line
and still enable the devices to ring when you
receive a call.The general rule is that the REN
value should not exceed 5.0 total; however,
contact your local telephone company for the
specific number in your area.
This precaution may be particularly
important in rural areas.
Caution:Users should not attempt to
make such connections
themselves, but should contact
appropriate electric inspection
authority, or electrician, as
appropriate.
Notice: The REN assigned to this device
denotes the number of devices
you may connect to the
telephone loop,whice is used by
the device to prevent verloading.
The termination on a loop may
consist of any combination
devices subjected only to the
requirement that the sum of the
REN does not exceed five.(5.0)
This device complies with RSS-210 of
Industry Canada. Operation is subject to
thefollowingtwo conditions: (1) this device
may not cause interference, and (2) this
device must accept any interference,
including interference that may cause
undesiredoperationof the device.
TECHNICAL
SPECIFICAT IONS
FREQUENCY CONTROL
CrystalControlled Dual PLLSynthesizer
TRANSMIT FREQUENCY
Handset: 925.05MHz to 927.75 MHz
Base: 902.3 MHz to 905.0 MHz
RECEIVE FREQUENCY
Handset: 902.3 MHz to 905.0 MHz
Base: 925.05MHz to 927.75 MHz
NOMINAL EFFECTIVE RANGE
Maximum power allowed by FCC and IC.
Actual operating range may vary according
toenvironmentalconditions at the time of use.
SIZE
Handset: 17.5cm x 5.5cm x 3.9cm
(L x W xT) maximum
(antenna excluded)
Base: 19.3cm x 14.8cm x 5.4cm
(L x W x T) maximum
(antenna excluded)
WEIGHT
Handset: 166 grams
Base: 321 grams
POWER REQUIREMENTS
Handset: Self-contained nickel-
cadmium rechargeable
battery supply, 3.6V
nominal, 400mAh capacity.
Power Adapter: 9V DC @ 200mA
SPECIFICATIONS ARE TYPICAL AND
MAY CHANGE WITHOUT NOTICE.
FCC AND IC REGULATIONS
12 13
14 15