V-tech VCS601 User manual

Voir le français à la page 15.
Haut-parleur de conférence
Bluetooth
VCS601, VCS601-1, VCS601-2
Guide d'utilisation
Bluetooth Conference
Speakerphone
VCS601, VCS601-1, VCS601-2
User Guide

2
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce
the risk of re, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use
a damp cloth for cleaning.
4. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6. Slots and openings in the speakerphone are provided for ventilation. To protect them from
overheating, these openings must not be blocked by placing the product on a soft surface such as
a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This
product should not be placed in any area where proper ventilation is not provided.
7. This product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supplied at the premises, consult your dealer or local power
company.
8. Do not allow anything to rest on the power cord. Do not install this product where the cord may be
walked on.
9. Never push objects of any kind into this product through the slots in the speakerphone because
they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on
the product.
10.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized
service facility. Opening or removing parts of the speakerphone other than specied access doors
may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric
shock when the product is subsequently used.
11. Do not overload wall outlets and extension cords.
12.Unplug this product from the wall outlet and refer servicing to an authorized service facility under
the following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operation instructions. Improper adjustment of other
controls may result in damage and often requires extensive work by an authorized
technician to restore the product to normal operation.
E. If the product has been dropped and the speakerphone has been damaged.
F. If the product exhibits a distinct change in performance.
13.Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of
electric shock from lightning.

3
14.Do not use the speakerphone or its connected telephone to report a gas leak in the vicinity of the
leak. Under certain circumstances, a spark may be created when the adapter is plugged into the
power outlet, or when the handset is replaced in its cradle. This is a common event associated with
the closing of any electrical circuit. The user should not plug the speakerphone into a power outlet
if the speakerphone is located in an environment containing concentrations of ammable or ame-
supporting gases, unless there is adequate ventilation. A spark in such an environment could create
a re or explosion. Such environments might include: medical use of oxygen without adequate
ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
15.For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be
easily accessible.
SAVE THESE INSTRUCTIONS
The applied nameplate is located at the bottom and rear side of the product base.
Battery Cautions Statement
Avoid using battery in the following conditions:
• High or low extreme temperatures that a battery can be subjected to during use, storage or
transportation;
• Low air pressure at high altitude;
• Replacement of a battery with an incorrect type that can defeat a safeguard;
• Disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery, that can
result in an explosion;
• Leaving a battery in an extremely high temperature surrounding environment that can result in an
explosion or the leakage of ammable liquid or gas;
• Extremely low air pressure that may result in an explosion or the leakage of ammable liquid or gas.
For cUL compliance only

4
Congratulations
on purchasing your new VTech product. Before using this product, please read the “Important safety
instructions” on page 2-3 of this manual.
This user guide provides a reference for the external features of the VCS601 Bluetooth Conference
Speakerphone and basic installation instructions.
For customer service or product information, visit our website at businessphones.vtech.com
or call 1 [phone]. In Canada, call 1 [phone].
For VCS601, VCS601-1, VCS-601-2:
FCC ID:EW780-S113-00
IC: 1135B-80S11300
HVIN:35-400336BCS
What’s in the box
Your product package contains the following items.
Save your sales receipt and original packaging in the event warranty service is necessary.
Bluetooth Conference Speakerphone
with built-in battery
Quick
Installation
Guide
VCS601
VCS601-1
VCS601-2
Storage bag
USB type A to
USB type C cable

5
Charging the battery
Built-in battery
USB type C
connnector
OR
(1)
(1)
USB type A
connector
< 8 hours
not included
(1)
Bluetooth Conference Speakerphone
Connectors
USB type A
connector
USB type C
connector
3.5 mm audio
input/output jack
FCC ID: EW780-S113-00
IC: 1135B-80S11300
HVIN: 35-400336BCS
CAN ICES-3 (B)/NMB-3(B)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND
2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
C300
PN: 00004584
Snom Technology GmbH,
Wittestr. 30 G, 13509 Berlin Germany
© 2021 Snom Technology GmbH. All rights reserved.
Made in China
Input : 5V 1.3A
Output : 5V 2.0A
A/V I.C.T.E.
RnX S/N: XXXYY8888899999
Microphones, 6 total

6
Top view
NFC zone 8 multicolored
LED indicators
(circle)
Volume +
key
Mute key
Factory
reset key
Speaker
Phone key
Volume –
key
Bluetooth key
Power key
Power LED
LED Indicators Overview
Power LED
Color Pattern Description
White Steady ON Power on and no USB power
connected
-OR-
Power on and charging completed.
OFF Power o󰀨 and no USB power
connected
-OR-
Power o󰀨 and charging completed
Flashing ON 1s OFF 1s Charging in power on mode
-OR-
During rmware upgrade
Flashing ON 2s OFF 4s Charging with power o󰀨
Red Steady ON Charging, but the battery level is too
low to power on the speakerphone
Power LED

7
LED 2
LED 8
LED 4LED 5
LED 1
LED 7
LED 6 LED 3
Multicolored LED indicators (circle)
Denitions
ON: LED steady on
ON x s, O󰀨 x s: blinking, x seconds on, x seconds o󰀨
Red
LED 1-8 ON: Mute microphones
LED 1-8 ON 0.12s, OFF 0.12s twice every 3 minutes:
Low battery warning
LED 1, 3, 5, 7 ON 0.2s, OFF 0.2s for a total of 3s:
Factory reset
Green (USB mode)
LED 1-8 ON 2s: USB data connection is ready
LED 1-8 ON 1s OFF 1s: Call ringing
LED 1 ON 2s: Volume level 1-2
LED 1 & 2 ON 2s: Volume level 3-4
LED 1-3 ON 2s: Volume level 5-6
…
LED 1-8 ON 2s: Volume level 15-16
Blue (Bluetooth mode)
ON 0.2s OFF 3s: Bluetooth is not paired or
paired device is not available
ON 0.2s OFF 0.2s: Bluetooth pairing
ON 2s: Bluetooth is ready
ON 1s OFF 1s: Call ringing
ON 0.25s, OFF 0.25s, ON 0.25s, OFF 2s :
Call Waiting
LED 1 ON 2s: Volume level 1-2
LED 1 & 2 ON 2s: Volume level 3-4
LED 1-3 ON 2s: Volume level 5-6
…
LED 1-8 ON 2s: Volume level 15
Purple
LEDs ON 2s to indicate battery charge level
LED 1-8: 100% LED 1-4: 50%
LED 1-7: 87.5% LED 1-3: 37.5%
LED 1-6: 75% LED 1-2: 25%
LED 1-5: 62.5% LED 1: 12.5%
and then OFF one by one every 2s in the
following order: LED 8, 7, 6, 5, 4, 3, 2, 1.
White
LED 1-8 ON 1s: NFC detected
LED 1-8 ON 2s: Power up
LED 1 ON: Voice is active near LED 1 area
LED 2 ON: Voice is active near LED 2 area
LED 3 ON: Voice is active near LED 3 area
…
LED 8 ON: Voice is active near LED 8 area
LED 1-8 ON 0.4s, and then OFF one by one
every 0.4s in the following order: LED 8, 7, 6, 5,
4, 3, 2, 1 : Press and hold Power key in power
on state
Red and Green
LED 1, 2, 5, 6 ON red & LED 3, 4, 7, 8 ON green: Firmware upgrading

8
Power on/o󰀨
To turn the speakerphone on:
• Press and hold the key for between two and ve seconds.
The speakerphone plays a power up melody.
The power LED indicator is illuminated when the speakerphone is on.
The power LED indicator ashes when the speakerphone is on and its battery is charging.
To turn the speakerphone o󰀨:
• Press and hold the key for more than ve seconds.
The mulitcolored LEDs fully turn on in white, and then turn o󰀨 one by one. The speakerphone
plays a power down melody.
The power LED indicator ashes slowly when the speakerphone is o󰀨 and its battery is charging.
Connecting to a Windows PC via USB
1. Plug the USB cable in the USB-C port on the speakerphone
2. Plug the other end of the USB cable in the USB-A port on your Windows PC.
When the speakerphone is recognized by your Windows PC, all the multicolored LEDs turn green
for two seconds. The speakerphone becomes the external audio device of your Windows PC.
Connecting to a Windows PC or mobile device
via Bluetooth pairing
1. When the speakerphone is idle, press and hold the key for more than
two seconds.
All the multicolored LEDs ash blue rapidly.
2. On your Windows PC or mobile device, open the Bluetooth menu.
If necessary, start Bluetooth or WLAN scanning/detection.
3. Select VCS601 from the list of available devices.
4. If you are asked for a PIN code, enter 0000.
• If pairing is successful: The speakerphone plays three ascending tones. All the multicolored
LEDs turn blue for two seconds.
• If pairing failed: The speakerphone plays three rapid tones. All the multicolored LEDs briey
turn blue every three seconds. Try again or try pairing with a di󰀨erent Bluetooth device.

9
Pairing your mobile device using NFC
NOTE: iPhone does not support Bluetooth pairing through NFC.
1. On your mobile device, turn NFC on.
2. Place the NFC zone of your mobile device against the NFC zone of the speakerphone (indicated
by ).
When NFC is detected, the speakerphone plays a tone. All the multicolored LEDs turn white for
one second.
3. If you are asked for a PIN code, enter 0000.
• If NFC pairing does not work, try again or try connecting via Bluetooth pairing.
Speakerphone functions
Play audio
When your speakerphone is paired to a Windows PC or mobile device, it acts as an external speaker
and plays audio from the paired device.s
When your speakerphone is playing audio from a paired Bluetooth device, the Bluetooth audio will be
interrupted and changed to PC audio immediately if you connect the speakerphone to the Windows
PC with the USB cable.
When your speakerphone is playing PC audio, this audio will be interrupted and changed to mobile
audio if there is an incoming mobile phone call.
Receive a call
When your paired mobile phone receives an incoming call, the speakerphone rings and all the
multicolored LEDs ash blue.
When there is an incoming call from a PC application, the speakerphone rings and all the multicolored
LEDs ash green.
Answer an incoming call
• Press the key.
During the call, the multicolored LEDs turn white to indicate from which direction the microphones
are receiving sound.
Call Waiting
If your paired mobile phone receives an incoming call while a call is in progress, the speakerphone
beeps twice.
• Press the key to hold the current call and switch to the incoming call.
Reject an incoming call
• Press and hold the key for at least two seconds.
End a call
• Press the key.

10
Volume
• Press the key to increase listening volume by one step.
• Press and hold the key to increase listening volume continuously.
• Press the key to decrease listening volume by one step.
• Press and hold the key to decrease listening volume continuously.
In Bluetooth mode, the multicolored LEDs turn blue for two seconds to indicate the volume level. The
more blue LEDs displayed, the higher the volume level.
In USB mode, the multicolored LEDs turn green for two seconds to indicate the volume level. The
more green LEDs displayed, the higher the volume level.
The speakerphone will synchronize playback volume with a USB-connected Windows PC, or a
Bluetooth-connected iPhone or Android phone (model dependent).
The speakerphone will synchronize phone call audio volume with a Bluetooth-connected iPhone or
Android phone.
Mute
• Press the key to mute all the microphones.
• Press the key again to unmute all the microphones.
• Press the key while the speakerphone is ringing to temporarily mute the ringing tone.
Activate Google Assistant, Siri or Bixby on the mobile device
• When the speakerphone is idle, press and hold the key for at least two seconds.
Connecting a headset
To ensure privacy during a phone call, you can connect a headset to the 3.5mm jack of the
speakerphone. The audio will be played through the headset.
Charging
To charge the battery of your speakerphone:
1. Plug the USB cable in the USB type-C port on the speakerphone
2. Plug the other end of the USB cable in the USB type-A port of a power source (for example, a
Windows PC).
While charging, the power LED indicator ashes white.
If the power LED indicator is red, the battery is charging but the battery level is too low for the
speakerphone to power up.
To charge an external device using the speakerphone battery:
1. Plug the USB cable in the USB type-A port of the speakerphone.
2. Plug the other end of the USB cable in the USB type-C port of the external device.
NOTE: The speakerphone must be on and the battery must not be low.
You can charge the battery of your speakerphone (USB type-C port) and charge an
external device using the speakerphone battery (USB type-A port) at the same time.