Vacmaster VDK1430SFC User manual

VDK1430SFC
30L 1400W
Original Instructions

1
2
3
9
10
13
14 15 16
22
17
23
20 21
26
19
25
18
24
11
12
4
5
6
7
8

6
GB
TABLE OF CONTENTS
SECTION PAGE
Symbols……………….......……….....................................................................................................
Safety Information.............................................................................................................................
Unpacking and Checking Carton Contents........................................................................................
Assembly……………….......………..................................................................................................
Operation……………….......………................................................................................................
Maintenance………….......………....................................................................................................
Troubleshooting………….......………...............................................................................................
Technical Data………….......……….................................................................................................
Recycling and Disposal………….......………...................................................................................
Plug/Fuse Replacement (UK & Ireland Only ).................................................................................
6
7
9
9
10
12
13
14
14
14
Thank you for purchasing this Vacmaster® wet and dry vacuum cleaner. Feel condent that with
Vacmaster®you are obtaining a high quality product engineered for optimal performance. This
vacuum cleaner is suitable for use with both liquids and dry materials.
FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS.
SYMBOLS
Caution
Read operator’s manual.
Vacuum cleaners of dust category L according to IEC/EN 60335-2-69
for dry vacuuming of materials with an exposition limit value > 1mg/m3
that are hazardous to one's health.
WARNING:
The vacuum cleaner may contain materials that
are hazardous to one's health. Have the emptying and maintenance,
incl. the disposal of dust-collection container,
carried out by a
specialist. Appropriate protective equipment is required. Do not
operate the vacuum cleaner without the complete lter system.
Otherwise there is danger to your own health.

7
GB
SAFETY INFORMATION
This machine is intended for commercial use, for example in
hotels, schools, hospitals, factories, shops, ofces and rental
businesses. Any other use is considered as improper use. The
manufacturer accepts no liability for any damage resulting from
improper use. The risk for such improper use is borne solely by
the user.
When using the equipment, a few safety precautions must be
observed to avoid injuries and damage. Please read the complete
operating manual with due care. Keep this manual in a safe
place so that the information is always available. If you give
the equipment to any other person, give them these operating
instructions as well. We cannot accept any liability for damage or
accidents which arise due to a failure to follow these instructions
and the safety information.
READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER.
• Never leave the appliance switched on unattended, if you leave
the work area, switch the appliance off or unplug it from the
power supply.
• Do not vacuum or use this vacuum cleaner near ammable
liquids, gases or explosive vapours like gasoline or other fuels,
lighter uids, cleaners, oil-based paints, natural gas, hydrogen,
or explosive dusts like coal dust, magnesium dust, grain dust
or gun power. Sparks inside the motor can ignite ammable
vapours or dust.
• This vacuum cleaner is not suitable for the vacuuming of
asbestos or asbestos dust.
• Do not vacuum anything that is burning or smoking, such as
cigarettes, matches, or hot ashes.
• Ensure the hose and connections are always pointed away
from the users face, hair, ears and eyes during operation and
never direct the nozzle towards persons or animals.

8
GB
• Clear the working area of any items or possessions that you do
not wish to be vacuumed before operation.
• Keep cord away from heated surfaces.
• Do not expose to rain. Store indoors.
• Do not unplug by pulling on the cord. To unplug, grasp the plug,
not the cord.
• Do not use with damaged cord, plug or other parts.
• Do not pull or carry by cord, use cord as handle, close a door
on cord, or pull cord around sharp edges or corners.
• Do not handle the plug or vacuum cleaner with wet hands.
• To reduce the risk of health hazards from vapours or dusts, do
not vacuum toxic materials.
• Frequently check that the oat valve positioned underneath the
motor is able to move freely.
• Do not use or store near hazardous materials.
• Do not use this vacuum cleaner with a torn lter or without the
lter installed.
• Do not allow to be used as a toy. Close attention is necessary
when used by or near children.
• To reduce the risk of injury from accidental starting, unplug
power cord before changing or cleaning lter.
• Unplug from power supply when not in use and before carrying
out maintenance.
• Do not cover the ventilation openings. Do not vacuum with any
ventilation openings blocked; keep free of dust, lint, hair or
anything that may reduce air ow.
• Keep hair, loose clothing, ngers, all parts of body away from
openings and moving parts.
• If the supply cord is damaged, it must be replaced by the
manufacturer, a qualied service agent or similarly qualied
persons in order to avoid a hazard.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.

9
GB
• For additional protection: It is recommended that this vacuum
cleaner can be used in conjunction with residual current device
(RCD) with a rated residual current of 30mA or less.
• Only use the socket outlet on the machine for purposes
specied in the instructions.
• If foam or liquid escapes from the machine, switch off
immediately.
• Clean the oat valve regularly and examine it for signs of
damage.
• Precautions should be taken when changing attachments.
• For user servicing, the machine must be dismantled, cleaned
and serviced, as far as is reasonably practicable, without
causing risk to the maintenance staff and others. Suitable
precautions include decontamination before dismantling,
provision for local ltered exhaust ventilation where the
machine is dismantled, cleaning of the maintenance area and
suitable personal protection.
• Perform a technical inspection at least annually, consisting of,
for example, inspection of lters for damage, air tightness of the
machine and proper function of the control mechanism.
• Besides the operating instructions and the binding accident
prevention regulations valid in the country of use, observe
recognized regulations for safety and proper use.
• When dust removers are used, the rate at which air is
exchanged in the room must be adequate if the exhaust
air from the vacuum cleaner is blown into the room (please
observe regulations valid in your country).
• Before starting work, the operating staff must be informed on
- use of the vacuum cleaner
- risks associated with the material to be picked up
- safe disposal of the picked up material.
• Before transporting the collection tank, close all the locks. Do
not tilt the cleaner if there is liquid in the collection tank. Do not
use a crane hook to lift the cleaner.
• When using an extension lead, check the minimum cross-
sections of the cable:

10
GB
Cable length
Cross section
< 16 A < 25 A
up to 20 m 1.5 mm22.5 mm2
20 to 50 m 2.5 mm24.0 mm2
When carrying out service or repair
operations, all contaminated items which cannot be
satisfactorily cleaned are to be disposed of; such items shall
be disposed of in impervious bags in accordance with any
current regulation for the disposal of such waste.
WARNING:
UNPACKING AND CHECKING CARTON
CONTENTS
When using as blower:
• Direct air discharge only at work area.
• Do not use Wet/Dry Vacuum as a sprayer.
• Do not direct air at bystanders.
• Keep children away when blowing.
• Wear safety goggles.
1 Carry Handle 10 Blowing Port 19 Dust Bag
2 Filter Cleaning Button 11 Power Take-off Socket 20 Round Dusting Brush
3 On/Off Switch 12 Hose Storage Rack 21 Power Tool Hose Adaptor
4 Power Regulator 13 Power Cord Storage Hook 22 Metal Extension Wand (x3)
5 Latch 14 Squeegee Inserts 23 Foam Filter
6 Suction Port 15 Brush Inserts 24 Cartridge Filter (pre-installed)
7 Container 16 Floor Nozzle 25 Screw (x6)
8 Drainage Port 17 Suction Hose 26 Instruction Manual
9 Caster 18 Crevice Tool

11
GB
OPERATION
1. Switching On/Off
Connect the mains plug to a suitable power outlet.
Position Status
I on
Ooff
II automatic synchronized start-up
ASSEMBLY
NOTE: A Phillips screwdriver is required.
1. Remove all the contents from inside of the vacuum cleaner container.
2. Attach the carry handle into the slots located on the top of the power head (Fig. 1).
3. Turn the container upside down and insert the feet with casters into the slots and apply
pressure until they click into place. Secure them with supplied screws (Fig. 2).
4. To position the hose storage rack, insert one end into the channel on the side of the power
head, making sure it is secured in place. Apply inward pressure to the other side and insert it
into the opposite channel (Fig. 3).
5. Your vacuum cleaner comes ready for dry vacuum cleaning with the cartridge lter pre-installed.
If the cartridge lter is not installed, refer to page 12.
6. Optionally, for improved dust ltration, fully t the dust bag ange onto the inlet stub (Fig. 4).
7. For wet vacuum cleaning, replace the cartridge lter with the foam lter supplied. Do not use a
dust bag when wet vacuuming. If the foam lter is not installed, refer to page 13.
8. Secure the power head back on the container using the latches. Insert the locking end of the
hose into the suction port of the container. Ensure the push clip is securely positioned (Fig. 5).
9. Choose the desired accessories and/or extension wands and push t onto the hose nozzle.
Floor Nozzle Attachments
The oor nozzle comes supplied with additional attachments to ensure correct suction across
different oor surfaces and applications.
1) To remove the oor nozzle attachments, turn the oor tool holder upside down.
2) Using a athead screwdriver or other suitable tool, locate the holding clips on each outer edge.
Insert a at edged object directly next to the holding clip, between the insert and the oor tool
holder. Pry the attachment up from underneath (Fig. 6 & 7).
3) Insert the new attachments into the holder applying downwards pressure (Fig. 7).
4) The attachments can be used in three combinations (Fig. 8):
Brush and Squeegee Combination: For use with mixture of wet or dry liquids.
Dual Brush Combination: For use with dry materials or carpeted oor surfaces.
Dual Squeegee Combination: For use on hard oor with wet liquids
Note: The textured side of the rubber squeegee must be facing outwards.

12
GB
The airow can be continuously adjusted by turning the power regulator (Fig. 10).
MIN: Reduced suction for applications which generate a low level of dust.
MAX: Maximum suction performance for use in applications which generate a high level of dust.
4. Filter Cleaning Operation
IMPORTANT: Only perform the lter cleaning operation when the cartridge lter is installed.
If the suction performance diminishes, you can improve the suction power with the help of the lter
cleaning system.
1) Position the end of the suction hose nozzle into the channel located within the lter cleaner
button.
2) Move the on/off switch to the “I” position.
3) Turn the power regulator to the MAX position.
4) Press the lter cleaning button down and hold it down for 3-4 seconds (Fig. 11).
5) Repeat the process two more times.
5. Wet & Dry Vacuum Operation
WARNING! ENSURE YOU READ, UNDERSTAND AND APPLY SECTION
ENTITLED ‘SAFETY INFORMATION’.
1) Verify that the correct lter is installed and the container latches are secured.
2) Secure the locking end of the hose into the vacuum suction port.
3) Push the desired accessories onto the hose nozzle. The air ow regulation allows you to
change vacuum cleaner suction. For best cleaning results, fully close the air ow regulation
(Fig. 12).
4) Plug the power cord into a power outlet.
5) Turn on the motor by assigning the switch to the “I” ON position.
6) Once you have completed vacuuming, switch to the “O” OFF position and unplug the power
cord from the power outlet.
For Dry Vacuuming:
WARNING: BEFORE INSTALLING, REMOVING OR CLEANING THE VACUUM
CLEANER FILTER, ENSURE THAT THE POWER CORD IS UNPLUGGED AND
SWITCHED OFF.
1) To prepare your vacuum cleaner for dry vacuuming, install the cartridge lter over the lter
cage. Carefully push lter until it sits ush forming a tight seal. Tighten the lter retainer lock
clockwise to secure against the internal lter cage (Fig. 13).
3) Switch the vacuum cleaner to position II, as described in Switching ON/OFF. The moment you
switch on the power tool, the vacuum cleaner will also switch on. Once the electrical appliance
has been switched off, the vacuum cleaner switches off following a time lapse
(around 5 seconds) to allow the suction tube to be emptied.
3. Power Regulator
2. Power Tool Take-Off Operation (Fig. 9)
WARNING: Always check the maximum wattage compatibility of the power tool take
off socket against the desired power tool before connecting to prevent overloading.
1) Connect the power cable of your power tool to the power take-off socket.
2) If applicable, connect the vacuum suction hose to the dust extractor connector on your tool with
the supplied adaptor.

13
GB
2) Optionally, fully t the dust bag ange onto the inlet stub. The vacuum cleaner can we be used
with or without dust bags.
IMPORTANT: Check the lter regularly for optimal performance. An old or blocked lter will reduce
suction performance.
For Wet Vacuuming:
1) To prepare your vacuum cleaner for wet vacuuming, release the retainer lock and remove the
dry use cartridge lter.
2) Carefully install the supplied foam lter over the internal lter cage, making sure the whole cage
is covered (Fig. 14).
WARNING:
DO NOT USE THE CARTRIDGE FILTER FOR WET VACUUMING.
DO NOT USE A DUST COLLECTION BAG FOR WET VACUUMING.
IMPORTANT! When vacuuming large quantities of liquids, do not immerse the nozzle completely;
leave a gap at the tip of the nozzle to allow air inow. The machine is tted with a oat valve that
stops the suction action when the container reaches its maximum capacity. You will notice an
increase in motor noise. When this happens, turn off the machine, disconnect from power supply,
and drain the liquid using the drainage hose. Ensure the drainage cap is re-installed before
continuing to vacuum.
6. Blower Operation
1) Make sure the container and any collected waste is emptied before using as a blower. This also
includes removal of the dust bag.
2) Insert the locking end of the hose into the blowing port on the side of the power head (Fig. 15).
3) Turn on the motor on by turning the switch to the ‘I’ ON position.
WARNING: KEEP BYSTANDERS CLEAR FROM BLOWING DEBRIS.
WARNING: ONLY WORK WITH A CLEAN SUCTION HOSE. DO NOT
USE THE BLOWER FUNCTION IN AN ENCLOUSED SPACE OR FOR DUSTS
WHICH ARE HAZARDOUS TO HEALTH. DO NOT INHALE DUSTS. DO WEAR
A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE INHALED.
WARNING: ONLY USE THE BLOWING FUNCTION FOR CLEANING,
REMOVING DUST, OR DRYING MACHINES AND APPLIANCES.

14
GB
MAINTENANCE
WARNING: REMOVE THE POWER CORD FROM THE POWER SUPPLY BEFORE
CARRYING OUT ANY MAINTENANCE.
1) Keep all safety devices, air vents and the motor housing free of dirt and dust. Use a soft, dry
brush to clean the equipment regularly.
2) Clear all dirt or debris from the collection tank after each use. Allow to dry before replacing the
power head. Do not use cleaning agents or solvents; these may damage the appliance.
3) Check the hose, attachments, and power cord to verify that they have not been damaged or
any debris is trapped and blocking airow.
1. Cleaning Cartridge Filter
Remove the lter and clean by gently tapping or brushing off dirt. For optimal performance it is
recommended to replace the old lter with a new lter regularly.
2. Cleaning Foam Filter
Remove the foam lter and use a mild soap and water solution to wash and rinse with clean water
(Fig. 16). Allow lter to air dry before installing and using again.

15
GB
TROUBLESHOOTING
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG BEFORE
TROUBLESHOOTING.
Cleaning Performance
Vacmaster vacuum cleaners are tested for endurance. If your motor is operating, then the most
likely cause for a loss in suction is a blockage or an opening in the vacuum.
To maintain a high cleaning performance from your machine, it is important to replace or clean
cartridge lters as necessary. Replace full dust bags to prevent performance drops. A performance
drop with clean lters can only be caused by a blockage in the tools or the hose.
PROBLEM POSSIBLE CAUSE SOLUTION
The appliance does not work.
No power. Check the power supply and
fuse.
Functional fault in the power
cord, switch, or motor.
Have the damaged part
checked by qualied personnel
or contact the after sales
helpline.
Dust is escaping from the
motor cover.
The cartridge lter is missing
or damaged.
Put in a cartridge lter or
replace it.
Misuse the cartridge lter
when wet vacuuming, causing
the damage of cartridge lter.
Replace the damaged
cartridge lter with a new one
when dry vacuuming.
Misuse the foam lter when
dry vacuuming.
Replace the foam lter with the
cartridge lter.
Power tool take-off socket
does not work.
Power tool wattage is not
compatible with the power tool
take-off socket.
Check the wattage is
compatible with the power tool
take-off socket.
Incorrect operating mode
selected.
Ensure the switch is moved
into position II.
Low suction power and high
operating noise / vibrations.
Dust bag is full. Replace the dust bag.
Suction nozzle, hose, or tank
inlet is blocked.
Check the suction nozzle, hose,
and tank inlet for obstructions.
Cartridge lter is blocked. Remove the cartridge lter and
clean.
Float valve has closed.
Empty the container of any
liquid waste and ensure the
oat value located underneath
the lter is able to move freely.
Power regulator switch is set
to minimum.
Adjust variable power
regulator.

16
GB
RECYCLING AND DISPOSAL
TECHNICAL DATA
Model Number VDK1430SFC
Motor 220-240V~50Hz
Power Input 1400W
Max. Power Consumption Of the Power
Tool Take-Off Socket Outlet
1590W for BS Socket
2280W for VDE Socket
Tank Volume 30L
Net Weight 9kg
Max. Vacuum Pressure 24kPa / 240hPa
Max. Flow Rate 68L/s / 244.8m³/h
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. The machine must be delivered in rigid packaging to avoid damage during
transportation. The packaging and the machine itself are manufactured from recyclable
materials and should be disposed of accordingly.
Noise/Vibration Information
Noise emission values determined according to EN 60335-2-69.
Typically, the A-weighted sound pressure level of the power tool is <77 dB(A).
Uncertainty K = 3 dB. The noise level when working can exceed 80 dB(A).
Total vibration values ah (triax vector sum) and uncertainty K determined according to
EN 60335-2-69: ah<2.5 m/s2, K =1.5 m/s2.

17
GB
PLUG/FUSE REPLACEMENT (UK &
IRELAND ONLY)
This product is tted with a non-rewirable plug. If the plug has to be changed, refer to the picture
below.
6mm
6mm
FUSE
FITTED WITH BS 1362 13A FUSE ALWAYS RT FIT BS 1362 REPLACEMENT CARTRIDGE FUSE
6mm
32mm
E
L
N
13A
GREEN&
YELLOW
OR
GREEN
BROWN
OR
RED
CORD GRIP
BLUE
OR
BLACK

1
15
12
4
13
12
11
14
3
7
9
6
MAX MIN
MAX MIN
15 16
8
10