VADDIO WallVIEW 50i PTZ HideAway User manual

Installation and User Guide
Camera and Electronic Products for Integrators
Ⓒ2006 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are
subject to change without notice. Vaddio, WallVIEW, ControlVIEW, EZCamera, Quick-Connect and PowerRite are registered trademarks of
Vaddio. All other trademarks are property of their respective owners. Document Number 010-2201-000 Rev. F
Page 1 of 8
WallVIEW™ PTZ Systems
WallVIEW 50i PTZ, WallVIEW 100 PTZ and WallVIEW 70 PTZ
Pan/Tilt/Zoom Camera Systems
INTRODUCTION
The Vaddio WallVIEW PTZ Camera Systems are complete wall-mounted camera
packages featuring the Vaddio EZCamera™ Cabling System that allows the installer to
use Category 5 cabling to run power, video and camera control. The included
PowerRite™ power supply provides the right amount of power required for proper
operation of the camera over Cat. 5 cabling.
INTENDED USE Before installing the Vaddio WallVIEW PTZ Camera Systems, please read
the entire manual thoroughly. All Vaddio camera systems were designed
for use indoors. Outdoor operation is not recommended, hasn’t been
tested, and could damage the camera and/or create a potentially unsafe
operating condition. Use only the Vaddio PowerRite power supply
provided.
IMPORTANT
SAFEGUARDS Read and understand all instructions before using. Do not operate any
electrical device if it has been dropped or damaged. In this case, a Vaddio
technician must examine the product before operating. To reduce the risk
of electric shock, do not immerse in water or other liquids and avoid
extremely humid conditions.
Figure 1: WallVIEW Systems (left to right); WallVIEW 50i PTZ, WallVIEW 100 PTZ, WallVIEW 70 PTZ, with each camera showing
EZCamera Cabling Shoe and Thin Profile wall mount bracket.
Use only the power supply provided with the Vaddio WallVIEW products.
Use of an
y
unauthorized
p
ower su
pp
l
y
will void an
y
and all warranties.

Vaddio WallVIEW – Document Number – 010-2201-000 Rev. F
Page 2 of 8
UNPACKING
Carefully remove all of the parts from the packaging. Unpack and identify the
following parts for each of the WallVIEW systems:
WallVIEW 100 PTZ
Part Numbers: 999-2204-000 (NTSC) and 999-2204-001 (PAL)
•One (1) Sony® EVI-D100 Camera (not included in WallVIEW Kit)
•Vaddio IR Remote Commander for Sony Cameras (not included in Kit version)
•One (1) Vaddio EZCamera Cable Shoe for D100 camera
•One (1) Thin Profile wall mount bracket (matching color)
•One (1) 12’ (3.66m) S-Video cable
•One (1) 12’ (3.66m) Composite video cable (RCA connectors)
•One (1) Vaddio Quick-Connect™ Box
•One (1) EZCamera Control Adapter
•One (1) 15VDC PowerRite power supply with power cable
For PAL camera versions, both EURO and UK Power cables are included.
•Mounting hardware & Documentation
WallVIEW 70 PTZ
Part Numbers: 999-2704-000 (NTSC) and 999-2704-001 (PAL)
•One (1) Sony EVI-D70 Camera (not included in WallVIEW Kit)
•Vaddio IR Remote Commander for Sony Cameras (not included in Kit version)
•One (1) Vaddio EZCamera Cable Shoe for D70 camera
•One (1) Thin Profile wall mount bracket (matching color)
•One (1) 12’ (3.66m) S-Video cable
•One (1) 12’ (3.66m) Composite video cable (RCA connectors)
•One (1) Vaddio Quick-Connect™ Box
•One (1) EZCamera Control Adapter
•One (1) 18VDC PowerRite power supply with power cable
For PAL camera versions, both EURO and UK Power cables are included.
•Mounting hardware & Documentation
WallVIEW 50i PTZ
Part Numbers: 999-4204-000 (NTSC) and 999-4204-001 (PAL)
•One (1) Canon® VC-C50i Camera with Canon IR Remote
•One (1) Vaddio EZCamera Cable Shoe for 50i Camera
•One (1) Thin Profile wall mount bracket
•One (1) 12’ (3.66m) S-Video cable
•One (1) 12’ (3.66m) Composite video cable (RCA connectors)
•One (1) Vaddio Quick-Connect™ Box
•One (1) EZCamera Control Adapter
•One (1) 18VDC PowerRite power supply with power cable
For PAL camera versions, both EURO and UK Power cables are included.
•Mounting hardware & Documentation
Important Note:
The table below provides minimum and maximum CAT-5 cable distances that can be
used with the standard and optional power supplies with each camera system. 24
VDC power supplies are available as an accessory (Part # 451-2000-024).
18 VDC Power Supply
(included) 24 VDC Power Supply (sold separately)
WallVIEW 100 Up to 115 ft.
(35.1m)
115 ft. to 250 ft.
(35.1m to 76.2m)
WallVIEW 70 Up to 200 ft.
(61m)
200 ft. to 300 ft.
(61m to 91.4m)
WallVIEW 50 Up to 185 ft.
(56.4m)
185 ft. to 275 ft.
(56.4m to 83.8m)

Vaddio WallVIEW – Document Number – 010-2201-000 Rev. F
Page 3 of 8
INSTALLATION The WallVIEW products are cameras specifically designed for installation on a
vertical wall surface with Cat. 5 cable connectivity for Power, Video and Control
signaling. Installation is simplified in that no custom 8-Pin mini-din cables or
expensive S-Video plenum cables are needed and no power outlets are required
near the camera bracket. All cabling is routed to the head-end using Cat. 5 cabling
with the EZCamera Cabling system.
Before
Installing •Locate the camera mounting location paying close attention to camera viewing
angles, lighting conditions, possible line of site obstructions, and checking for
in-wall obstructions where the camera is to be mounted. Pick a mounting
location to optimize the performance of the camera.
•Pre-wire all cabling as required (see wiring diagram examples).
•The WallVIEW 100, 70 and 50i can be mounted to standard 2-gang wall
boxes. All cameras are basically lightweight and the thin profile wall mount
bracket can be adequately secured to the wall with the four (4) provided
conical plastic wall anchors (or your choice of dry wall anchor).
Wiring
Diagram
Examples
The Basic Idea: WallVIEW 50i, 70 & 100 PTZ
Figure 2:
The WallVIEW 50i, 70 & 100 uses a single cat. 5 for Power and Video and a 2nd Cat. 5 for control.
Control is wired in a daisy chain configuration if a single control port is to be used.
Daisy Chain
Control
Configuration
Note:
TXD, RXD & GND are required for basic control. For Daisy Chaining, DSR and DTR are required for
Sony products (Pins 1 and 2 on the Cat. 5 cable) and CTS and RTS are Required for Canon products
(Pins 3 and 4 on the Cat. 5 cable).
ProductionVIEW
Super Joystick
RS-232
S-Video or
Composite
Video or Both
Cat. 5
Power to Camera
Video From Camera
WallVIEW 100 PTZ
with Camera, Shoe
and Mount
Cat. 5
Quick-Connect Box
Display, Projector
or Codec Power Supply
Figure 3:
Vaddio ControlVIEW™ Xtreme Camera
Controller with Single RS-232 Control Port
controlling 3 WallVIEW 100s in Daisy Chain
Configuration
RS-232
OUT
RS-232
IN
RS-232
OUT
RS-232
IN
RS-232
OUT
RS-232
IN

Vaddio WallVIEW – Document Number – 010-2201-000 Rev. F
Page 4 of 8
MOUNTING
INSTRUCTIONS Step 1:
After determining the optimum location of the camera system, route the Cat. 5
cabling from the camera to the Quick-Connect Box located at the head-end. The
cable should pass through the oval slot located on the rear flange of the wall
mount (Figure 4).
Be sure to leave several inches of Cat. 5 extending out from the wall for ease of
connection.
Step 2: If the bracket is to be mounted on a 2-gang wall box, use the screws supplied with
the wall box cover plate to attach the Thin Profile wall mount bracket. If the
bracket is to be mounted to the dry wall, then mark and drill 3/16” (4.76mm) holes.
Make sure that the holes line up and provide a level, flat mounting surface. Tap in
the four (4) provided plastic conical wall anchors and mount the wall mount to the
anchors with the supplied sheet metal screws.
Step 3: Carefully attach the Vaddio EZCamera Shoe to the back connector plate of the
camera. Note: Do not force, the shoe should slide into place and make positive
connection with a minimum of effort.
Step 4: Place the camera onto the camera mount and plug in the Cat. 5, RJ-45
connectors. Using the supplied ¼”-20 machine screw, secure the camera to the
mount through the mounting slot (see Figure 4). Gently push camera back
towards the rear of the mount, feeding the excess cable into the wall or wall box,
until the shoe is held up against the wall mount, then tighten bottom screw.
Figure 4:
Wall Mount bracket showing oval cabling
through-hole on back of mounting flange.
Mount may be mounted to the wall with
conical wall anchors or to 2-gang wall box
Figure 5:
WallVIEW 70 shown with EZCamera
Cable Shoe. Carefully slide the shoe
into place taking care to seat the
male connections firmly into place.
Press firmly into place
Figure 6:
WallVIEW 100 shown with camera
shoe and mount. Slide the camera
and shoe back to touch the shoe and
mount together, then tighten ¼”-20
screw.
¼”-20 mounting screw
through bottom slot
Press to back of mount Slide camera to back of mount and ti
g
hten

Vaddio WallVIEW – Document Number – 010-2201-000 Rev. F
Page 5 of 8
Step 5: Attach the Cat. 5 cable for Power and Video on the Quick-Connect Box. Use the
supplied Video cables and plug these cables from the Quick-Connect Box to the
video destination (codec, monitor, projector). Connect the PowerRite power
supply to the Quick-Connect Box power input (see Figure 2).
Step 6: Verify all connections. Please check all Cat. 5 cables for continuity in advance to
final connection. This will save hours of trouble shooting time.
Connect only the Vaddio supplied power supply to an AC outlet. Power will travel
down the Cat. 5 cable to the cable shoe, powering the camera. The camera will
“Home” to a centered position ready for control information from the provided
Vaddio IR Remote Commander (WallVIEW 70, 100) or Canon IR Remote
(WallVIEW 50i PTZ) or RS-232 Camera controller of the integrators’ choice.
Completing the
Installation To insure proper continuity of control and operation of the cameras, the RS-232
controller (control system or joystick) should be powered on after the cameras.
The cameras should be powered up first in the control line. Depending on how
your programs are written, and if the cameras are turned off every night, please
adhere to the described power–up order to ensure proper operation.
INFORMATION For documents on video, power and control pin-outs, please see the Vaddio
website under Vaddio Technical Note #101 or the Appendix at the back of this
manual.
For RS-232 control information, please see the full-length manuals for each of the
manufacturer’s camera models (Sony EVI-D100, EVI-D70 and Canon VC-C50i)
either on the Vaddio or the manufacturer’s website www.vaddio.com
.
Vaddio has prepared a number of TechNotes, specifications and drawings
designed to inform and educate integrators’ of the value and the specific uses of
Vaddio products.
CARE AND
CLEANING •Do not attempt to take the products in these systems apart. There are no
user-serviceable components inside.
•Do not spill liquids on the products
•Keep these devices away from food and liquid
•For smears or smudges on the lens, wipe with a clean, soft cloth. Do not use
any abrasive chemicals on the camera body at any time.
OPERATING AND
STORAGE
CONDITIONS
Do not store or operate the WallVIEW System under the following conditions for
any circumstance:
•Temperatures above 40°C (104°F)
•Temperatures below 0°C (32°F)
•High humidity, condensing or wet environments
•Dusty environments
•In inclement weather
•Under severe vibration

Vaddio WallVIEW – Document Number – 010-2201-000 Rev. F
Page 6 of 8
WARRANTY
INFORMATION Hardware* Warranty - One year limited warranty on all parts. Vaddio warrants
this product against defects in materials and workmanship for a period of one year
from the day of purchase if Vaddio receives notice of such defects during the
warranty. They will, at its option, repair or replace products that prove to be
defective.
Exclusions - The above warranty shall not apply to defects resulting from:
improper or inadequate maintenance by the customer, customers applied software
or interfacing, unauthorized modifications or misuse, operation outside the normal
environmental specifications for the product, use of the incorrect power supply, or
improper site operation and maintenance.
Vaddio Customer Service – Vaddio will test, repair, or replace the product or
products without charge if the unit is under warranty. If the product is out of
warranty, Vaddio will test then repair the product or products. The cost of parts
and labor charge will be estimated by a technician and confirmed by the customer
prior to repair. All components must be returned for testing as a complete unit.
Vaddio will not accept responsibility for shipment after it has left the premises.
Vaddio Technical Support - Vaddio technicians will determine and discuss with
the customer the criteria for repair costs and/or replacement. Vaddio Technical
Support can be contacted through one of the following resources: e-mail support
at [e-mail]
.
Return Material Authorization (RMA) Number - Before returning a product for
repair or replacement request an RMA from Vaddio’s technical support. Provide a
technician with a return phone number, e-mail address, shipping address, and
product serial numbers. Describe the reason for repairs or returns as well as the
date of purchase. Include your assigned RMA number in all correspondence with
Vaddio. Write your assigned RMA number on the outside of the box when
returning the product.
Voided Warranty – The warranty does not apply if the original serial number has
been removed or if the product has been disassembled or damaged through
misuse, accident, modifications, or unauthorized repair.
Shipping and Handling - Vaddio will not pay for inbound shipping transportation
or insurance charges or accept any responsibility for laws and ordinances from
inbound transit. Vaddio will pay for outbound shipping, transportation, and
insurance charges for all items under warranty but will not assume responsibility
for loss and/or damage by the outbound freight carrier. If the return shipment
appears damaged, retain the original boxes and packing material for inspection by
the carrier. Contact your carrier immediately.
Products not Under Warranty - Payment arrangements are required before
outbound shipment for all out of warranty products.
*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in
accordance with industry standard practices.

Vaddio WallVIEW – Document Number – 010-2201-000 Rev. F
Page 7 of 8
Appendix 1:
Vaddio Power, Video and Control Pin-outs
For Vaddio Cameras: WallVIEW 50i PTZ, WallVIEW 70 PTZ and WallVIEW 100 PTZ
Power/Video Connection RJ-45 – Camera Shoe
# Pins
1) Power (+)
2) Power GND
3) Video GND
4) Y (luminance)
5) Video GND
6) C (Chrominance)
7) Video GND
8) Composite Video
RS-232 Connector IN – Camera Shoe
# Pins
1) DTR (Sony® Daisy chain to DSR)
2) DSR (Sony Daisy chain from DTR)
3) CTS (Canon® Daisy chain to RTS)
4) RTS (Canon Daisy chain from CTS)
5) Unused
6) Digital GND
7) RXD (from TXD of control source)
8) TXD (to RXD of control source)
RS-232 Connector Out – Camera Shoe
# Pins
1) DSR (Sony Daisy chain from DTR)
2) DTR (Sony Daisy chain to DSR)
3) RTS (Canon Daisy chain from CTS)
4) CTS (Canon Daisy chain to RTS)
5) Unused
6) Digital GND
7) TXD (to RXD of control source)
8) RXD (from TXD of control source)
Power/Video Connection – RJ-45 – Quick-Connect Box
# Pins
1) Power +
2) Power GND
3) Video GND
4) Y (luminance)
5) Video GND
6) C (Chrominance)
7) Video GND
8) Composite Video
Power
Video
Power/Video Connector
Power/Video
Connector
RS-232 IN
RS-232 OUT
RS-232 IN
Vaddio Camera Shoe
Back View
Top
View
Vaddio Camera Shoe
Back View
RS-232 OUT
12345678 Vaddio Camera Shoe
Back View
RS-232
In
12345678
12345678
RS-232
Out
Top
View
RJ-45
Power/Video
Connector to
Camera Shoe
S-Video
From
Camera Composite
Video From
Camera
Power Supply
To Camera Shoe
12345678
Power
Video

Vaddio WallVIEW – Document Number – 010-2201-000 Rev. F
Page 8 of 8
Ⓒ2008 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are
subject to change without notice. Vaddio, WallVIEW, ControlVIEW, EZCamera, ProductionVIEW, Quick-Connect and PowerRite are
registered trademarks of Vaddio. All other trademarks are property of their respective owners. Document Number 010-2201-000 Rev. F