Valley Comfort Systems Blaze King PRINCESS PE1006 User manual

180-PE1006 v1.11 October 3, 2018
The authority having jurisdiction (such a municipal building department, fi re department, etc.) should be
consulted before installation to determine the need to obtain a permit.
Pour la version française de nos manuels S.V.P. vous référez à notre site web: www.blazeking.com
Manufactured By
Valley Comfort Systems Inc., 1290 Commercial Way, Penticton, BC, V2A 3H5, Canada
Phone: [phone] w Fax: [phone] w www.blazeking.com w [email protected]
OPERATION & INSTALLATION MANUAL
PRINCESS PE1006/PEJ1006
SOLID FUEL CATALYTIC STOVE
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please SAVE THESE INSTRUCTIONS for future reference.
This heater meets the 2015 U.S. Environmental Protection Agency’s particulate emission limits for wood heaters sold after May 15, 2015.
PE1006BK PE1006LBK PE1006UBK

180-PE1006 v1.11 October 3, 2018
Page 2 PE1006
INTRODUCTION _____________________________________________________________ 4
SPECIFICATIONS _____________________________________________________________ 5
EMISSIONS __________________________________________________________________ 5
PRODUCT INFORMATION _____________________________________________________ 6
APPLIANCE DIMENSIONS—Princess Classic PE1006BK .............................................................. 6
APPLIANCE DIMENSIONS—Princess Parlor PE1006LBK ............................................................. 7
APPLIANCE DIMENSIONS—Princess Ultra PE1006UBK.............................................................. 8
CERTIFICATION LABEL________________________________________________________ 9
SAFETY PRECAUTIONS ________________________________________________________ 10
INSTALLATION INSTRUCTIONS_________________________________________________ 13
PARTS INCLUDED WITH THE PRINCESS ................................................................................... 13
OPTIONAL EQUIPMENT............................................................................................................... 13
FLOOR PROTECTION .................................................................................................................... 13
MINIMUM CLEARANCES for PE1006 and PEJ1006...................................................................... 14
COMBUSTION AIR......................................................................................................................... 15
DRAFTING PERFORMANCE ......................................................................................................... 15
ROLE OF THE CHIMNEY............................................................................................................... 15
VENTING SYSTEMS ...................................................................................................................... 16
RECOMMENDED FLUE HEIGHTS................................................................................................ 19
MOBILE HOME (AND RESIDENTIAL ALCOVE INSTALLATIONS)........................................... 20
OPTIONAL ACCESSORIES............................................................................................................. 21
OPERATING INSTRUCTIONS ___________________________________________________ 24
INTRODUCTION ............................................................................................................................ 24
YOUR FIRST FIRE!.......................................................................................................................... 24
BYPASS ............................................................................................................................................ 24
CATALYTIC THERMOMETER ....................................................................................................... 24
THERMOSTAT ................................................................................................................................ 25
SELECTING WOOD........................................................................................................................ 25
HOW TO USE MOISTURE METERS.............................................................................................. 26
EFFICIENCY.................................................................................................................................... 26
LIGHTING THE FIRE ..................................................................................................................... 27
RELOADING PROCEDURE (with the catalyst temperature in the ACTIVE ZONE) ....................... 28
RELOADING PROCEDURE (with the catalyst temperature still in the INACTIVE ZONE)............. 28
OPTIMAL THERMOSTAT SETTING ............................................................................................. 28
FAN OPERATION ........................................................................................................................... 29
ICE - FORMATION AND PREVENTION ....................................................................................... 29
WOOD BURNING IN THE SHOULDER SEASON ......................................................................... 29
CATALYST MONITORING ______________________________________________________ 30
CATALYST MONITORING ______________________________________________________ 30
CATALYTIC COMBUSTOR, TESTING ........................................................................................... 30
CATALYTIC COMBUSTOR, CLEANING ....................................................................................... 30
CATALYTIC COMBUSTOR, TROUBLESHOOTING...................................................................... 31
CATALYTIC COMBUSTOR, REPLACEMENT ............................................................................... 33
TABLE OF CONTENTS

180-PE1006 v1.11 October 3, 2018
Page 3
PE1006 TABLE OF CONTENTS
MAINTENANCE ______________________________________________________________ 36
RUN-AWAY OR CHIMNEY FIRE.................................................................................................... 36
CREOSOTE FORMATION AND REMOVAL .................................................................................. 36
CHIMNEY MAINTENANCE........................................................................................................... 36
CHIMNEY MAINTENANCE........................................................................................................... 37
FIRE EXTINGUISHERS AND SMOKE DETECTORS..................................................................... 37
ASH REMOVAL ...............................................................................................................................37
LOADING DOOR GASKET INSPECTION...................................................................................... 38
LOADING DOOR GASKET REPLACEMENT................................................................................. 38
BYPASS DOOR GASKET INSPECTION.......................................................................................... 38
BYPASS DOOR GASKET REPLACEMENT..................................................................................... 39
DOOR GLASS GASKET INSPECTION ........................................................................................... 40
DOOR GLASS GASKET REPLACEMENT ...................................................................................... 40
DOOR GLASS, CLEANING............................................................................................................. 40
LOADING DOOR TENSION ADJUSTMENT ................................................................................. 41
OPTIONAL FAN ASSEMBLY .......................................................................................................... 42
THERMOMETER ............................................................................................................................ 42
THERMOSTAT ................................................................................................................................ 42
TROUBLESHOOTING__________________________________________________________ 43
REPLACEMENT PARTS ________________________________________________________ 46
WARRANTY _________________________________________________________________ 53
INSTALLER NOTES____________________________________________________________ 60

180-PE1006 v1.11 October 3, 2018
Page 4 PE1006
INTRODUCTION
• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND IS PROHIBITED BY
FEDERAL AND STATE LAWS.
• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating
instructions could cause fi re or injury.
• Before installing this appliance, contact the local building or fi re authority and follow their guidelines.
• This appliance must be installed by a qualifi ed installer.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not operate without fully assembling all components.
• Do not let the appliance become hot enough for any part to glow red.
• Do not install damaged, incomplete or substitute components.
• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may be sharp.
• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing
ignition.
• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and
others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house.
To restrict access to an appliance or appliance, install an adjustable safety gate to keep toddlers, young children and other at risk
individuals out of the room and away from hot surfaces.
• Clothing or other fl ammable material should not be placed on or near the appliance. Objects placed in front of the appliance must be
kept a minimum of 48” away from the front face of the appliance.
• Due to high temperatures, the appliance should be located out of traffi c and away from furniture and draperies.
• Ensure you have incorporated adequate safety measure to protect infants / toddlers from touching hot surfaces.
• Even after the appliance is out, all surfaces, including the glass and/or any attachment will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety hearth guards to protect children from hot surfaces. These guards must be
fastened to a wall and/or to the fl oor.
• Any safety guard removed for servicing must be replaced prior to operating the appliance.
• Under no circumstances should this appliance be modifi ed.
• This appliance must not be connected to a chimney fl ue pipe servicing a separate solid fuel burning appliance.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done by a licensed
or qualifi ed service person.
• Do not strike or slam shut the appliance glass door.
• Operate only with the doors tightly closed.
• Appliance will over-fi re if door is not shut and latched.
• Only certifi ed doors / optional fronts / and surrounds for inserts with the unit are to be installed on the appliance.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags, these are
not toys and should be kept away from children and infants.
• If the appliance is not properly installed, a house fi re may result. Do not expose the appliance to the elements (rain, etc.) and keep the
appliance dry at all times.
• The chimney must be sound and free of cracks and obstructions. Clean your chimney regularly as required.
• Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fl uid, or similar liquids to start or ‘freshen up’ a fi re in this
heater. Keep all such liquids well away from the heater while it is in use.
• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to smoke spillage in your
home.
• Higher effi ciencies and lower emissions will generally result when burning air dried seasoned woods, as compared to wet, green or
freshly cut wood. Burning wet unseasoned wood can cause excessive creosote accumulation. When ignited it can cause a chimney
fi re that may result in a serious house fi re.
• The appliance is designed to burn seasoned wood only. Do not burn treated wood, coal, charcoal, colored paper, cardboard, solvents
or garbage.
• Burn wood directly on the fi rebricks. Do not use a grate or elevate the fi re.
• Do not store wood within appliance installation clearances or within the space required for re-fueling and ash removal.
• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well away from the home or
structure until completely cool.
CALIFORNIA PROPOSITION 65
WARNING: This product can expose you to chemicals including
benzene, which is known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information:
www.P65Warnings.ca.gov

180-PE1006 v1.11 October 3, 2018
Page 5
PE1006 SPECIFICATIONS
is unit was tested and listed UL 1482 (9/88) and ULC-S627 by Intertek
testing laboratories.
is manual describes the installation and operation of the Princess
PEJ1006 catalytic equipped wood heater.
is heater is certied to comply with the 2015 U.S. Environmental
Protection Agency’s particulate emission limits for wood heaters sold aer
May 15, 2015.
Under specic test conditions this heater has been shown to deliver heat at
rates ranging from 12000 to 35600 Btu/hr.
is wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal regulations
to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating instructions in this
manual.
is wood heater contains a catalytic combustor, which needs periodic inspection and replacement for proper operation.
It is against federal regulations to operate this wood heater in a manner inconsistent with operating instructions in this
manual, or if the catalytic element is deactivated or removed.
e combustor supplied with this heater is a Z4400G ceramic combustor. Consult the catalytic combustor warranty also
supplied with this wood heater. Warranty claims should be addressed to:
in Canada in USA
Blaze King Industries / Valley Comfort Systems
Warranty Department, 1290 Commercial Way
Penticton, BC Canada V2A 3H5, Ph: 250-493-7444
Blaze King Industries
Warranty Department, 146A Street
Walla, Walla, Washington 99362, Ph: 509-522-2730
EMISSIONS CO Average(%) g/hr
Low Burn 0.05 1.48
Med-low Burn 0.09 2.05
Med-high Burn 0.115 2.73
High Burn 0.4 3.51
EPA emission rate weighted average 2.42 g/hr
Model PE/PEJ 1006 (catalytic)
Height Classic 29 1/8” (740 mm)
Height Parlor 33 5/8” (854 mm)
Height Ultra 35” (889 mm)
Width 27” (686 mm) (without removable bypass handle)
Depth 30 3/4” (781 mm) (without optional fan kit)
31 5/8” (804 mm) (with optional fan kit)
Flue collar 6” I.D.
Fire door opening 16 3/8” x 8 1/4” (416 mm x 210 mm)
Firebox depth 18” (458 mm) brick to brick, 20 1/2” (521 mm) brick to glass
Firebox width 21 1/8” (537 mm)
Firebox height 12 1/2” (318 mm)
Fire box capacity 2.85 cu. ft.
Recommended Fuel length 16” max. (407 mm)
Wood capacity (approximate): White oak - 60 lbs. (27.21 kg)
Fir - 40 lbs. (18.14 kg)
Construction 10 gauge & 1/4” fi rebox, brick lined.
16 gauge outer shields
Shipping Weight 355-400 lbs. (161-182 kg)
Chimney recommendation 15’ from stove top to chimney cap.

180-PE1006 v1.11 October 3, 2018
Page 6 PE1006
APPLIANCE DIMENSIONS—Princess Classic PE1006BK
PRODUCT INFORMATION














 








ZRSWLRQDOIDQV












180-PE1006 v1.11 October 3, 2018
Page 7
PE1006
APPLIANCE DIMENSIONS—Princess Parlor PE1006LBK
PRODUCT INFORMATION



 















 
















ZRSWLRQDOIDQV










180-PE1006 v1.11 October 3, 2018
Page 8 PE1006
PRODUCT INFORMATION
APPLIANCE DIMENSIONS—Princess Ultra PE1006UBK








 
















ZRSWLRQDOIDQV




180-PE1006 v1.11 October 3, 2018
Page 9
PE1006 CERTIFICATION LABEL
Residential Installations / Installations résidentielles ABCDEF
Roof exit, parallel and corner.
Sortie de toit, parallèle et coin.
16”
407mm
9”
229mm
29.5”
750mm
19.25”*
489mm
14”
356mm
28"*
712mm
Roof exit, reduced side. Use side shields
Sortie de toit, côté réduits. Utiliser des panneaux latéraux.
10”
254mm
9”
229mm
23.5”
597mm
19.25"*
489mm
Roof exit, reduced corner. Use side shields and either fan kit or rear shield
Sortie de toit, coin réduits. Utiliser des panneaux latéraux et kit de ventilateur / panneaux arrière.
6"
153mm
20"*
508mm
Roof exit, close clearance. Use side shields and either fan kit or rear shield. Sortie de toit,
dégagement étroit, utiliser des panneaux latéraux, et kit de ventilateur / panneauxr arrière.
10”
254mm
6”
153mm
23.5”
597mm
16.25”*
413mm
Wall exit, parallel and corner.
Sortie, parallèle et coin.
16”
407mm
9”
229mm
29.5”
750mm
19.25”*
489mm
14”
356mm
28"*
712mm
Wall exit, reduced side. Use side shields
Sortie de mur, côté réduit. Utiliser des panneaux latéraux.
10”
254mm
9”
229mm
23.5”
597mm
19.25”*
489mm
Wall exit, reduced corner. Use side shields and either fan kit or rear shield.
Sortie de mur, coin réduit. Utiliser des panneaux latéraux/ kit de ventilateur / panneaux arrière.
7"
178mm
21"*
535mm
Alcove roof exit. Use side shields and either fan kit or rear shield.
Chambrette, sortie de toit. Utiliser des panneaux latéraux/et kit de ventilateur / panneaux arrière.
10”
254mm
6”
153mm
23.5”
597mm
16.25”*
413mm
Mobile Home Installations / Installations pour maison mobile
Roof exit parallel and corner. Use side shields, either fan kit or rear shield and outside air kit
La sortie du toit, parallèle et le coin utiliser les boucliers latéraux, ou kit de ventilateur
ou un bouclier et un kit d ’air extérieur.
10”
254mm
6”
153mm
23.5”
597mm
16.25”*
413mm
6”
153mm
20”*
508mm
Floor protection may be any non-combustible material or Listed Floor Protector, and must extend at least 18” (458 mm) in Canada or 16” (407 mm) in
U.S.A., in front of the loading door opening. In USA, minimum size is 33” x 42 3/8” (839 x 1077 mm). In Canada, minimum size is 43” x 52 3/8” (1093
x 1331 mm).
U.S. ENVIRONMENTAL PROTECTION AGENCY - 2015 Standard - certifi ed to comply with 2015 particulate emission standards (EPA test methods
28 and 5G with an emission-rate of 2.42 g/hr). Not approved for sale after May 15, 2020. This wood heater needs periodic inspection and repair
for proper operation. Consult the owner’s manual for further information. It is against federal regulations to operate this wood heater in a manner
inconsistent with operating instructions in the owner’s manual, or if the catalytic element is deactivated or removed.
*ONLY OPERATE WITH DOORS CLOSED. Open door to feed fi re ONLY. *DO NOT OBSTRUCT COMBUSTION AIR OPENINGS. Do not obstruct the
space beneath the heater. For Use With Solid Wood Fuel Only - Do not burn other fuels, this may make the catalyst in the combustor inactive. The
performance of the catalytic device or its durability has not been evaluated as part of the certifi cation. Combustor part number: Z4400G. Provide
adequate outside air for combustion. *Replace with only ceramic glass, 5 mm. thickness.
POUR PRÉVENIR UN INCENDIE Installer et employer seulement selon le manuel des directives d’installation de Blaze King. Contacter les
fonctionnaires locaux de bâtiment ou de feu au sujet des restrictions et de l’inspection d’installation dans votre secteur.
La taille de conduite de cheminée est 6”.
CHEMINÉE: NE PAS CONNECTER CET APPAREIL A UN CONDUIT DE CHEMINÉE SERVANT UN AUTRE APPAREIL. Excepté pour les installation
détaillée ci-dessous, employer avec une cheminée 6” approuvé pour l’utilisation avec les combustibles solides et conformément à ULC629 au Canada
ou à UL-103HT aux Etats-Unis ou un type de cheminée résidentiel de maçonnerie.
Le dégagement étroit de maison mobile, et de les installations résidentielles de chambrette exigent des conduits de 6” à double paroi de cheminée
approuvé au dégagement de fi n de mur, avec une cheminée approuvée construite par une usine appropriée pour l’utilisation avec les combustibles
solides et conformément à, l’ ULC629 au Canada ou l’ UL-103HT AUX Etats-Unis. On permet seulement l’installation dans une maison mobile avec une
sortie de toit. Ne pas installer dans une chambre à coucher. Largeur minimum de 47” de chambrette " profondeur maximum 48 " taille minimum 49 "
au -dessus du poêle. Pour passer au travers d’un mur ou d’un plafond ceci exige des méthodes spéciales: voir les directives et les codes locaux de
bâtiment. Estimation électrique: 115VAC, 60 hertz , 0.58 ampêre , risque de choc électrique, débrancher l ’alimentation électrique avant l'entretien de
l’unité. Ne pas faire courir le cordon d’alimentation devant ou sous l 'appareil.
BLAZE KING CATALYST STOVE - PE(J)1006 W/N #16626
POÊLE À BOIS CATALYTIQUE
LISTED ROOM HEATER, SOLID FUEL TYPE / APPAREILLE APPROUVÉE DE TYPE CARBURANT
SUITABLE FOR MOBILE-HOME INSTALLATION. CONCU POUR MAISONS MOBILES.
Appareille approuvé de type carburant solide, aussi adapte pour installer une maison mobile.
MODEL/MODÈLE: PE1006/PEJ1006 Tested to / Testé: UL 1482 (9/88) / CSA B366.2 ULC S627
CERTIFIED IN BOTH UNITED STATES AND CANADA / CERTIFIÉ POUR LES ÉTATS-UNIS ET LE CANADA
MINIMUM CLEARANCES TO COMBUSTIBLES (See owners manual for complete description of all requirements)
DÉGAGEMENTS MINIMUM AUX COMBUSTIBLES (voir les directives d’installation dans le manuel pour la description complète de toutes les conditions)
MANUFACTURE DATE
JAN FEB MAR APR MAY JUN 
JUL AUG SEP OCT NOV DEC 
2015 2016 2017 2018 2019 2020 
La protection de plancher peut être n’importe quel matériel non combustible ou Protecteur de plancher approuvé, et doit se prolonger au moins, 18"
(458 mm) au Canada ou 16" (407 mm) aux Etats-Unis, devant l’ouverture de la porte de chargement. Aux Etats-Unis, la taille minimum est de 33” x 42
3/8” (839 x 1077 mm). Au Canada la taille minimum est 43” x 52 3/8” (1093 x 1331 mm).
AGENCE DE PROTECTION DE L’ENVIRONNEMENT U.S.- STANDARD 2015 – certifi é conformément aux normes standard d’émissions de particules
2015 (Méthodes de test 28 et 5G EPA avec un taux d'émission de 2.42 gr/hre). Non approuvé pour la vente après le 15 mai 2020. Cet appareil de
chauff age au bois nécessite des inspections périodiques et des réparations pour un fonctionnement adéquat. Consulter le manuel du propriétaire
pour plus d’informations. Il est contre les règlements fédéraux de faire fonctionner cet appareil de chauff age à l’encontre des instructions
d’utilisation fournies dans le manuel du propriétaire, ou si l’élément catalytique est enlevé ou désactivé.
*Utiliser uniquement avec les portes fermées. Ouvrir la porte pour alimenterl le feu SEULEMENT. *Ne pas obstruer l’ouverture d’air de combustion.
Fournir de l’air extérieur adéquat pour la combustion. Ne pas obstruer l’espace sous le poéle. Utiliser uniquement avec des combustibles solides
- Ne pas brûler aucune autres combustibles, ce qui peut rendre le catalyseur dans la chambre de combustion inactif. La performance du catalyseur
ou sa longévité n’a pas été évaluée dans le cadre de la certifi cation. Numéro de la pièce de combustion: Z4400G. *Employer seulement le verre en
céramique si le remplacement est nécessaire, d’une épaisseur de 5mm.
PREVENT HOUSE FIRES- Install and use only in accordance with Blaze King’s installation and operation instructions. Contact local building or fi re
offi cials about restrictions and installation inspection in your area. The fl ue size is 6".
CHIMNEYS: DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. Except for installation detailed below, use 6” listed
factory built chimney suitable for use with solid fuels and conforming to, ULC629 in Canada or UL-103HT in the USA or a masonry residential type
chimney.
Mobile Home, residential close clearance, and residential alcove installations require a 6” listed double wall close clearance chimney connector, with
matching listed factory built chimney suitable for use with solid fuels and conforming to, ULC629 in Canada or UL-103HT in the USA. Mobile Home
installations are only allowed with a roof exit. Do not install in a sleeping room. Alcove minimum width 47", maximum depth 48", minimum height 49"
above stove top. Passing through a wall or ceiling requires special methods: see instructions and local building codes. Electrical rating: 115 VAC, 60
Hz, 0.58 Amps. Risk of electrical shock. Disconnect power before servicing unit. Do not route power cord in front of or beneath heater.
Fabriqué au
 USA:
Blaze King Industries
146A Street
Walla Walla, WA.
99362
 CANADA:
Valley Comfort Systems
1290 Commercial Way
Penticton, B.C.
V2A 3H5
WH- P
#0217PE 06 15.indd
G - 3” (77 mm) in U.S.A.
8” (203 mm) in Cvanada
H - 16” (406 mm) in U.S.A.
18” (456 mm) in Canada
* Check with local codes and pipe manufacturer for pipe clearances. In Canada, 18” clearances from single wall pipe is required.
* Vérifi er avec les codes locaux et manufacturiers des conduits pour les dégagements. Au Canada, dégagement de 18” pour le tuyaux à paroi simple est requis

180-PE1006 v1.11 October 3, 2018
Page 10 PE1006
This appliance must be connected to a listed high temperature (ULC629 IN CANADA OR
UL-103HT IN THE USA) residential type factory built solid fuel chimney or an approved
masonry chimney with a fl ue liner.
Chimney and chimney connector must be in good condition and kept clean.
NEVER vent the stove to other rooms of the building. Must be vented to the outside ONLY.
NEVER use a chimney or chimney connector smaller then the stove exhaust, unless
approved by your local inspector.
NEVER vent the stove into a “Class B” gas vent chimney.
DO NOT CONNECT IN CONJUNCTION WITH ANY AIR DISTRIBUTION DUCTWORK
UNLESS SPECIFICALLY APPROVED FOR SUCH INSTALLATIONS.
Inspect the chimney connector and chimney regularly during each burning season and
clean when necessary.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
NEVER intentionally start a chimney fi re to clean the fl ue.
When installed in a mobile home, this appliance must be bolted to the fl oor and provided
with outside air.
WARNING: DO NOT INSTALL IN A SLEEPING ROOM
CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME
FLOOR, WALL, AND CEILING/ROOF MUST BE MAINTAINED.
Check with local building offi cials.
If the Optional Fan Kit is
installed, connect this unit to
a properly grounded, 110-volt
electrical outlet. Do not route
the power cord in front of or
under the appliance.
Do not make any changes or
modifi cations to an existing
masonry fi replace or chimney
to install this appliance. Do
not make any changes to
the appliance to increase
combustion air.
SAFETY PRECAUTIONS
IF THIS BLAZE KING APPLIANCE IS NOT PROPERLY INSTALLED OR OPERATED, A HOUSE FIRE MAY
RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. CONTACT LOCAL
BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION
REQUIREMENTS IN YOUR AREA.
PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW APPLIANCE. FAILURE TO
FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH.

180-PE1006 v1.11 October 3, 2018
Page 11
PE1006
Never try to repair or replace
any part of this appliance
unless instructions are given
in this manual. All other work
must be done by a trained
technician.
Allow the appliance to cool
down before carrying out any
maintenance or cleaning.
Maintain the door and glass
seal and keep them in good
condition. A leaking door seal
will shorten burn times and
may harm the combustor.
Avoid placing wood against
the glass when loading. Do
not slam the door or strike the
glass.
Do not throw this manual
away. This manual has
important operating and
maintenance instructions that
you will need at a later time.
Always follow the instructions
in this manual.
Do not place clothing or other
fl ammable items on or near
this appliance.
Do not use a grate or other
device to elevate the fi re off of
the fi rebox fl oor. Burn the fi re
directly on the bricks.
Ashes should be placed in a
steel container with a tightly
fi tting lid and moved outdoors
immediately. If the ashes are
disposed of by burial in soil or
otherwise locally dispersed,
they should be retained in
the closed container until
all cinders have thoroughly
cooled. Other waste shall not
be placed in this container.
SAFETY PRECAUTIONS
It is required in some jurisdictions to install smoke and carbon monoxide detectors where
heaters are installed. Install at least one smoke detector on each fl oor of your home to
ensure your safety. It should be located away from the wood appliance and close to the
sleeping areas. Locating a smoke detector too close to a wood appliance can cause the
smoke detector alarm to sound if a puff of smoke is emitted while the wood appliance door
is open during reloading. Follow the smoke detector manufacturers placement, installation,
and maintenance instructions.
DO NOT OVER FIRE THIS
HEATER. Attempts to
achieve heat output rates
that exceed heater design
specifi cations can result in
permanent damage to the
heater and to the catalytic
combustor. Over fi ring the
appliance may cause a house
fi re. Never burn the appliance
so hot that the appliance or
chimney connector begins to
glow.

180-PE1006 v1.11 October 3, 2018
Page 12 PE1006
Never burn the appliance
with the loading door open.
Leaving the door cracked
open may damage the
combustor.
Never block free airfl ow
through vents on this
appliance.
HOT WHILE IN OPERATION.
KEEP CHILDREN,
CLOTHING AND FURNITURE
AWAY.
CONTACT MAY CAUSE SKIN
BURNS.
Do not touch the appliance
when it is hot and educate all
children of the danger of a
high temperature appliance.
Young children should be
supervised when they are
in the same room as the
appliance.
This appliance must be
properly installed to prevent
the possibility of a house
fi re. The instructions must
be strictly adhered to. Do not
use makeshift methods or
compromise in the installation.
Do not use chemicals or fl uids
to start the fi re. Never use
gasoline, gasoline-type lantern
fuel, kerosene, charcoal lighter
fl uid, or similar liquids to start or
‘freshen up’ a fi re in this heater.
Keep all such liquids well away
from the heater while it is in use.
Some fuels could generate
carbon monoxide and are very
dangerous.
Keep furniture, curtains,
wood, paper and other
combustibles a minimum of
48in (1219mm) away from
the front of the appliance.
ALSO, DO NOT STORE
COMBUSTIBLES UNDER
THE APPLIANCE (WOOD,
PAPER etc.).
Contact local building offi cials
to obtain a permit and
information on any installation
restriction or inspection
requirements in your area.
Notify your insurance
company as well.
SAFETY PRECAUTIONS
This appliance is designed and approved for burning cord wood only. DO NOT burn trash,
garbage; artifi cial or paper logs; gift wrappings; coal; lighter fl uids; chemical cleaners;
chemical starters; treated or painted wood; salt water driftwood or foil-backed paper such
as gum wrappers or cigarette packages; lawn clippings or yard waste; materials containing
rubber (including tires), plastic, asbestos; waste petroleum products, paints or paint
thinners, or asphalt products; construction or demolition debris; railroad ties or pressure-
treated wood; manure or animal remains; unseasoned wood or paper products, cardboard,
plywood, or particleboard. The prohibition against burning these materials does not prohibit
the use of fi re starters made from paper, cardboard, saw dust, wax and similar substances
for the purpose of starting a fi re in an aff ected wood heater. Burning these materials may
result in the release of toxic fumes or render the heater ineff ective and cause smoke.
Burn natural wood only. It will void all warranties and safety listings and may damage the
combustor.

180-PE1006 v1.11 October 3, 2018
Page 13
PE1006 INSTALLATION INSTRUCTIONS
FLOOR PROTECTION
If the stove sits on a combustible fl oor, a non-combustible shield must be used underneath the
stove and extending 16” out from the front and 8” on either side of the fuel-loading door in the
USA. In Canada a non-combustible shield must be used underneath the stove and extending 8”
on either side and rear and 18” out in front of the loading door.
A non-combustible shield is also required underneath the chimney connector and extending at
least 2” (50.8mm) on either side of the chimney connector.
See the next page for minimum sizes depending on model. This fl oor protection is required
to prevent sparks from falling onto the combustible fl oor. See CSA B365-M87). This product
does not require thermal hearth pad protection.
Blaze King grants no warranty, implied or
stated, for the installation or maintenance of the
appliance and assumes no responsibility of any
consequential damage(s).
PARTS INCLUDED
1. Poker
2. Manual kit (w/ warranty cards, thermometer, fi re starter, bypass handle)
OPTIONAL EQUIPMENT
1. Fan kit (Z1714) 2. Convection deck (Z1744)
3. Rear shield (Z4015) 4. Ash drawer (Z1710 on parlor model)
5. Side Shields (ZSSP1006) (Classic / Parlor) 6. Fresh air kit (Z1726B)
• BEFORE INSTALLING THIS APPLIANCE, CONTACT THE LOCAL BUILDING OR FIRE OR OTHER
AUTHORITY HAVING JURISDICTION AND FOLLOW THEIR GUIDELINES.
• THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. FOLLOW THE
INSTALLATION DIRECTIONS. DO NOT OPERATE WITHOUT FULLY ASSEMBLING ALL
COMPONENTS.
• IF THIS APPLIANCE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT.
• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF
CONTACTED. CHILDREN AND PETS MUST BE KEPT FROM TOUCHING THE APPLIANCE
WHEN IT IS HOT.
• COMBUSTIBLE MATERIAL SUCH AS FIRE WOOD, WET CLOTHING, ETC. PLACED TOO CLOSE
CAN CATCH FIRE. OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A
MINIMUM OF 48”(1219 MM) FROM THE FRONT OF THE APPLIANCE.

180-PE1006 v1.11 October 3, 2018
Page 14 PE1006
INSTALLATION INSTRUCTIONS
MINIMUM CLEARANCES for PE1006 and PEJ1006
Residential Installations A B C D E F J
Roof exit, parallel and corner. No fan kit required. 16”
407 mm
9”
230 mm
29.5”
750 mm
19.25”*
489 mm
14”
360 mm
28”*
712 mm
49”
1245 mm
Roof exit, reduced side. Use side shields. 10”
254 mm
9”
230 mm
23.5”
597 mm
19.25”*
489 mm
49”
1245 mm
Roof exit, reduced corner. Use side shields and either fan kit or rear
shield.
6”
153 mm
20”*
508 mm
49”
1245 mm
Roof exit, close clearance. Use side shields, and either fan kit or
rear shield.
10”
254 mm
6”
153 mm
23.5”
597 mm
16.25”*
413 mm
49”
1245 mm
Wall exit, parallel and corner. No fan kit required. 16”
407 mm
9”
230 mm
29.5”
750 mm
19.25”*
489 mm
14”
360 mm
28”*
712 mm
49”*
1245 mm
Wall exit, reduced side. Use side shields. 10”
254 mm
9”
230 mm
23.5”
597 mm
19.25”*
489 mm
49”*
1245 mm
Wall exit, reduced corner. Use side shields and either fan kit or rear
shield.
7”
180 mm
21”*
535 mm
49”*
1245 mm
Alcove, roof exit. Use side shields, and either fan kit or rear shield. 10”
254 mm
6”
153 mm
23.5”
597 mm
16.25”*
413 mm
49”
1245 mm
Mobile Home Installation
Roof exit, parallel and corner. Use side shields, either fan kit or rear
shield and outside air kit.
10”
254 mm
6”
153 mm
23.5”
597 mm
16.25”*
413 mm
6”
153 mm
20”*
508 mm
49”
1245 mm
* Check with local codes and pipe manufacturer for pipe clearances. In Canada, 18” clearances from single wall pipe is required.
G = 3” (76mm) in USA
8” (203mm) in Canada
H = 16” (406mm) in USA
18” (456mm) in Canada
I = 0” (0mm) in USA
8” (203mm) in Canada
K = 18” (456mm) for single wall pipe in Canada
Ember protection shield (not required to have an insulation value)
is to be listed under UL 1618-2009 (type 1) and must have a minimum size of:
In USA: 33” x 42 3/8” (839 x 1077 mm)
In Canada: 43” x 52 3/8” (1093 x 1331 mm)
Min. Alcove minimum width 47”, maximum depth 48”, minimum height above stove top 49”
This stove must be installed in compliance with all local codes and regulations.

180-PE1006 v1.11 October 3, 2018
Page 15
PE1006 INSTALLATION INSTRUCTIONS
COMBUSTION AIR
Ensure adequate combustion air allowing for all other exhausting type appliances in the dwelling (range hoods,
dryers, etc.). In air tight homes and modern constructions, careful considerations must be taken into account
when using a wood burning appliance. Heat recovery ventilators (HRV) systems along with constant running
fan motors in air handlers must be taken into account when balancing the system. Failure to do so may
result in air starvation, smoke spillage and carbon monoxide threats. Consult a HVAC specialist for proper
installation. Ensure adequate combustion air allowing for all other exhausting type appliances in the dwelling
(range hoods, dryers, etc.). In airtight houses it is recommended to install a fresh air inlet into the room where
the appliance is located, to prevent air starvation.
ROLE OF THE CHIMNEY
Without a proper installed chimney, this appliance will not burn correctly.
The role of the chimney is to pull the proper amount of air into the fi rebox for the purpose of complete
combustion. Incomplete combustion will lead to more smoke and pollution of the outside air. A proper
operating chimney will allow the user to enjoy peak performance at all burn operating levels from low to high.
Blaze King therefore recommends vertical installations with a minimum length of 15’ from stove top to chimney
cap. In all freestanding stove installations, use double wall stove pipe from the stove top to the ceiling support
box. The use of double wall stove pipe does allow for reduced clearances, however most importantly, it helps
to keep the chimney warm and improve draft.
For wall exits, the same suggestion applies. With the addition of the recommendation to use two 45 degree
elbows rather than a single 90 degree elbow. The use of two 45 degree elbows will allow for both a smoother
transition to the exterior chimney and will also shorten the horizontal run to the outside chimney. A minimum
36” rise is recommended prior to any elbows being used. When possible, outside chimney systems should
be isolated from direct exposure to winter weather by building a chase around the chimney, observing all
clearances as specifi ed by the venting manufacturer. Doing so will help to keep the chimney warmer and
improve draft.
DRAFTING PERFORMANCE
Draft is the force which moves air into the appliance up through the chimney. The amount of draft created by
your chimney depends upon length, off sets, insulating properties, obstructions (such as architectural design,
trees), local geography and other factors.
External forces, such as outdoor temperature, wind, barometric pressure, topography, or factors inside the
home (negative pressure from exhaust fans, chimneys, air infi ltration, etc) may adversely aff ect draft.
Too much draft may cause excessive temperatures in the appliance and may damage the heater. An
uncontrollable burn or excessive temperature indicates excessive draft.
Inadequate draft may cause back puffi ng (spillage) into the room and plugging of the chimney, chimney cap or
spark arrestor screen. Inadequate draft may cause smoke to leak into the room through appliance or chimney
connector joints. Poor draft can also lead to poor heat production and the inability for the combustor to remain
active in lower burn rate settings.
High effi ciency appliances, such as your Blaze King stove, may require some fi ne tuning of your chimney
system in order to maximize performance.
Blaze King cannot be responsible for external forces leading to less than optimal performance.

180-PE1006 v1.11 October 3, 2018
Page 16 PE1006
INSTALLATION INSTRUCTIONS
VENTING SYSTEMS
The venting system consists of a chimney connector and a chimney. These get extremely hot during use.
Temperatures inside the chimney may exceed 2000 degrees in the event of a creosote fi re. To protect against
the possibility of a house fi re, the chimney connector and chimney must be properly installed and maintained.
A listed thimble must be used when a connection is made through a combustible wall to a chimney. A chimney
support package must be used when a connection is made through the ceiling to a listed prefabricated
chimney. These accessories are absolutely necessary to provide safe clearances to combustible wall and
ceiling material.
This stove may be connected to a lined masonry chimney or a listed factory built chimney suitable for use with
solid fuels and conforming to, ULC629 in Canada or UL-103HT in the USA. Do not connect it to a chimney
serving another appliance. To do so will aff ect the safe operation of both appliances, and will void the stove
warranty. You must comply with the local authority having jurisdiction and/or in Canada, CSA installation
standard B365-M87.
The chimney connector must be 6” diameter, 24 MSG Black/Blue steel. Do not use aluminum or galvanized
steel. They cannot properly withstand the extreme temperatures of a wood fi re. The chimney connector
between the stove and the chimney should be as short and direct as possible.
The chimney connector must be attached to either an approved masonry chimney or one of the listed factory
built chimneys suitable for use with solid wood fuel. All joints must be tight and fastened with sheet metal
screws.
THE CHIMNEY CONNECTOR IS TO BE USED ONLY WITHIN THE ROOM, BETWEEN THE STOVE
AND CEILING / WALL. NEVER USE A CHIMNEY CONNECTOR TO PASS THROUGH AN ATTIC
OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED SPACE, OR A FLOOR, OR CEILING. AN
EFFECTIVE VAPOR BARRIER MUST BE MAINTAINED AT THE LOCATION WHERE THE CHIMNEY
OR COMPONENT PENETRATES TO THE EXTERIOR OF THE STRUCTURE. ALWAYS MAINTAIN
THE MINIMUM CLEARANCES TO COMBUSTIBLES AS REQUIRED BY THE APPLICABLE BUILDING
CODES.

180-PE1006 v1.11 October 3, 2018
Page 17
PE1006 INSTALLATION INSTRUCTIONS
CONNECTION TO A METAL PREFABRICATED CHIMNEY
Refer to “RECOMMENDED FLUE HEIGHTS” chart for minimum fl ue height recommendations and ULC629
in Canada or UL-103HT in the USA for installation codes. When a metal prefabricated chimney is used, the
manufacturer’s installation instructions must be followed precisely. You must also purchase (from the same
manufacturer) and install the ceiling support package or wall pass through and “T” section package, fi re
stops (when needed), insulation shield, roof fl ashing, chimney cap, etc. Maintain the proper clearance to the
structure as recommended by the manufacturer. This clearance is usually a minimum of 2 inches, although it
may vary by manufacturer or for certain components.
There are basically two methods of metal chimney installation. One method is to install the chimney inside
the residence through the ceiling(s) and the roof. The other method is to install an exterior chimney that runs
up the outside of the residence (not recommended). If it is necessary to run the chimney outside, build an
outside chase around the chimney.
The chimney must be the required height above the
roof or other obstruction for safety and for proper draft
operation. The requirement is that the chimney must
be at least 3 feet higher than the highest point where it
passes through the roof and at least 2 feet higher than
the highest part of the roof or structure that is within 10
feet of the chimney, measured horizontally (Fig. 1). The
height requirement is necessary in the interest of safety
and does not necessarily assure proper fl ue draft. Use
a minimum total system height of 15 feet, measured
from the stove fl ue collar to the top of the chimney, not
including the chimney cap.

180-PE1006 v1.11 October 3, 2018
Page 18 PE1006
INSTALLATION INSTRUCTIONS
CONNECTION TO A MASONRY CHIMNEY
Masonry chimney***
Ensure that a masonry chimney meets the minimum standards
(NFPA) by having it inspected by a professional. Make sure there
are no cracks, loose mortar or other signs of deterioration and
blockage. Have the chimney cleaned before the stove is installed
and operated. When connecting the stove through a combustible
wall to a masonry chimney, special methods are needed.
In Canada, the wall cut away is to provide 18” clearance for the
connector. The resulting space must remain empty. A fl ush
mounted sheet metal cover may be used on one side only. If
covers are to be used on both sides, each cover must be mounted
on noncombustible spacers at least 1” clear of the wall.
***Blaze King recommends the use of a Stainless steel liner,
preferably insulated, inside a masonry chimney. This to
maintain proper draft and overall better operation of the unit.
Your local dealer or local jurisdiction can provide details of
approved methods of passing a chimney connector through a
combustible wall in your area. In USA, the National Fire
Protection Association has minimum standards to comply
with. In Canada , this type of installation must conform to
CAN/CSA-B365, Installation Code for Solid Fuel Burning
Appliances and Equipment.

180-PE1006 v1.11 October 3, 2018
Page 19
PE1006 INSTALLATION INSTRUCTIONS
RECOMMENDED FLUE HEIGHTS
1. At sea level the minimum height is a 15 ft (4.6 m) straight run.
2. Add the following vertical height to the fl ue to compensate for:
45° elbow = 1.0 ft (.30 m)
90° elbow = 2.0 ft (.61 m)
“T” section= 3.0 ft (.91 m)
3. Each foot of horizontal run = 2 ft (.61 m) of vertical rise.
Example: One 90° elbow = 2ft (.61 m)
2ft Horizontal run = 4ft (1.2 m)
One base “T” = 3ft (.91 m)
Total height addition = 9ft (2.7 m) at sea level
MINIMUM RECOMMENDED FLUE HEIGHT
ELEVATION
ABOVE SEA
LEVEL
NUMBER OF ELBOWS
0 2 X 15° 2 X 30° 2 X 45°
0 - 1000 ft
0 - 305 m
15
4.6 m
16
4.9 m
18
5.5 m
19
5.8 m
1000 - 2000 ft
305 - 610 m
15.5
4.7 m
16.5
5.0 m
18.5
5.6 m
19.5
5.9 m
2000 - 3000 ft
610 - 914 m
16
4.9 m
17
5.2 m
19
5.8 m
20
6.1 m
3000 - 4000 ft
914 - 1219 m
16.5
5.0 m
17.5
5.3 m
19.5
5.9 m
20.5
6.2 m
4000 - 5000 ft
1219 - 1524 m
17
5.2 m
18
5.5 m
20
6.1 m
21
6.4 m
5000 - 6000 ft
1524 - 1829 m
17.5
5.3 m
18.5
5.6 m
20.5
6.2 m
21.5
6.6 m
6000-7000 ft
1829 - 2134 m
18
5.5 m
19
5.8 m
21
6.4 m
22
6.7 m
7000 - 8000 ft
2134 - 2438 m
18.5
5.6 m
19.5
5.9 m
21.5
6.6 m
22.5
6.9 m
NOTE: No more than one off set (two elbows allowed).
Two 45°elbows equal one 90° elbow
Please note: These are only guidelines. Please refer to the section in the manual pertaining to draft. Every
installation is unique and can be infl uenced by topographical and geographical phenomena.
The use of a manometer and an understanding of pressure planes and the stack eff ect are imperative in
planning and executing a successful installation.

180-PE1006 v1.11 October 3, 2018
Page 20 PE1006
INSTALLATION INSTRUCTIONS
MOBILE HOME (AND RESIDENTIAL ALCOVE INSTALLATIONS)
Requires side shields and outside air kit, and either rear shield OR fan kit. (See next page for kits and part
numbers). e outside air kit is easiest to mount before the stove is installed. See instructions packed with
each kit. NOTE: UNDER NO CIRCUMSTANCES SHOULD THE FRESH AIR TUBE EVER BE
INSTALLED HIGHER THAN THE BOTTOM OF THE APPLIANCE FIREBOX FLOOR
When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed
precisely. You must also purchase (from the same manufacturer) and install the ceiling support package, re
stops (when needed), insulation shield, roof ashing, chimney cap, etc. Maintain the proper clearance to the
structure as recommended by the manufacturer.
Chimney connector must be double wall close clearance type with either ULC629 or ULCS610 designation.
Single wall pipe is not allowed in Mobile Homes or in Alcove Installations. Insulated chimney components
must be a listed factory built chimney suitable for use with solid fuels and conforming to, ULC629 in Canada or
UL-103HT in the USA. For Mobile home, the chimney needs to be removable to allow for transportation of the
mobile home.
DO NOT INSTALL IN SLEEPING ROOM. THE STRUCTURAL INTEGRITY OF THE MOBILE
HOME FLOOR, WALL AND CEILING / ROOF MUST BE MAINTAINED.
In mobile home installations, the stove must be securely fastened to the fl oor using the tie-downs
provided in the Outside Air kit. (For the pedestal model, remove the ash drawer to access the screw down
holes. For the Leg model, use the Leg Anchor Kit (P/N ZR8039) to secure stove to fl oor.)
ALSO, a #8 ground wire must be attached to the stove and an appropriate ground.
oor using the tie downs