VALSTEAM ADCA FLT32 User manual


VALSTEAM ADCA We reserve the right to change the design and material of this product without notice.
IMI 1.381 E 05.14
INSTALLATION AND MAINTENANCE INSTRUCTIONS
FLOAT & THERMOSTATIC STEAM TRAPS
FLT32
GENERAL
•These instructions must be carefully read before any work involving products supplied by VALSTEAM ADCA
ENGINEERING S.A. is undertaken.
•The installation procedure is a critical stage in a life of a steam trap and care should be taken to avoid damage
to the trap or equipment.
Warning!
- At start up, the presence of small particles in the water (dirt, scale, weld splatters, etc) may cause an imperfect
closure of the seat. If this occurs, proceed to an accurate cleaning.
- Do not touch the equipment without appropriate protection during working operation because it may conduct heat
if the used fluid is at high temperature.
- Before starting maintenance be sure that the equipment is not pressurized or hot.
- The equipments must be used within the working temperature and pressure limits laid down for them, otherwise
they may fail (refer to nameplate and/or IS- Information Sheet).
- Do not remove the nameplate attached to the equipment. Serial number and other useful information is stamped
on it.
INSTALLATION
- Before to install remove plastic covers placed on flanges or connection ends. The equipment has an arrow or
Inlet/Outlet designations. Be sure that it will be installed on the appropriate direction.
- Install the steam trap in the point of the system, where the condensate tends to collect. It must be installed with the
float lever in horizontal plane, so that it rises and falls vertically. An ADCA strainer should be installed upstream of
the trap.
BODY LIMITING CONDITIONS
FLANGED PN40 /
ANSI 300 lb *
FLANGED
ANSI 150 lb **
RELATED
TEMPERATURE
ALLOWABLE
PRESSURE
ALLOWABLE
PRESSURE
37,1 bar
15,4 bar
100 ºC
33,3 bar
13,8 bar
200 ºC
30,4 bar
12,1 bar
250 ºC
27,6 bar
10,2 bar
300 ºC
PMO –Max. operating pressure 32 bar;
TMO –Max. operating temperature 250 ºC;
*Acc. to EN1092-1:2018 ; **Acc. to EN1759-1:2004
Body limiting conditions PN40 or below, depending on the
type of connection adopted. Rating PN40 for thread, SW
and BW.
FLT32-4,5 4,5 bar
FLT32-10 10 bar
FLT32-14 14 bar
FLT32-21 21 bar
MAX. DIFFERENTIAL PRESSURE


VALSTEAM ADCA We reserve the right to change the design and material of this product without notice.
IMI 1.381 E 05.14
CE Marking:
This product has been designed for use on water and steam
which are in Group 2 of the European PED-Pressure Equipment
Directive in use and it complies with those requirements.
The product fall within category SEP and must not be CE marked.
Installation area requirements:
•The installation area should have easy access and provide enough space for maintenance and removing
operations.
•The installation area should have the necessary firing system to prevent damage of the equipment due to over
temperature/pressure cause by fire.
MAINTENANCE
•We recommend that the float steam traps are serviced as necessary. Steam traps should be checked
periodically (at least yearly), to verify that they are operating correctly and to clean the internal parts and screen
(if any).
•When reassembling make sure that all gasket faces are clean and always use a new gasket. Tighten cover
bolts uniformly in a diagonal sequence.
•For further information refer to the relevant FLT32 brochure or consult our Sales Office.
TROUBLESHOOTING
- If the malfunctions cannot be solved with the help of the following chart, please consult the manufacturer.
- Some of these faults may only occur in some models.
TROUBLE SHOOTING CHART
FAULT
POSSIBLE REASON
SOLUTION
Continuous steam discharge
Damaged seat.
Incorrect installation.
Substitute seat.
check the installation position
(see IMI 1.344 E 08.03).
The condensate isn’t discharged
Or not enough discharged
Obstructed strainer.
Inadequate pressure differential.
Proceed to an accurate clean and
identify the possible reason of
contamination.
Check the steam trap D.P. and
substitute.
MODEL SIZES CATEGORY
FLT32 ALL SEP
FLT32HC DN 25 1
GROUP 2 GASES CATEGORY


VALSTEAM ADCA We reserve the right to change the design and material of this product without notice.
IMI 1.381 E 05.14
Excessive back pressure.
Damaged float.
Replace the steam trap by a
superior DN or use ADCAMAT.
Replace.
Temporary condensate
accumulation
Steam blocking.
Downsizing.
Use a steam trap with SLR.
Check maximum flow rate (during
start-up)
Slow initial start up
Damaged air eliminator.
The air flow is too high for the trap.
Downsizing.
Replace.
Install an additional air eliminator.
Check maximum flow rate (during
start-up)
PARTS LIST FOR FLT32- STEAM TRAPS DN 1/2”- 1”, DN15-DN25
TRAP SIZE
DN
A.92.2402.015 Valve,seat,float&gasket D.P.4,5bar DN1/2”-1” 3,4,5,6,7 1Set
A.92.2403.015 Valve,seat,float&gasket D.P.10 bar DN1/2”-1” 3,4,5,6,7 1Set
A.92.2404.015 Valve,seat,float&gasket D.P.14 bar DN1/2”-1” 3,4,5,6,7 1Set
A.92.2405.015 Valve,seat,float&gasket D.P.21 bar DN1/2”-1” 3,4,5,6,7 1Set
A.92.2402.115 Float & gasket DN1/2”-1” 3,7 1Set
A.92.2402.215 Air vent & gasket DN1/2”-1” 3,7 1Set
CODE
DESIGNATION
QTY.
POS.NR.
Recommended tightening torques FLT32 DN 1/2”-1”, DN15-DN25
TRAP SIZE
DN
4 1/2”-1” 50±5
8 1/2”-1” 50±5
9 1/2”-1” 70±5
POS.NR.
Nm
Remarks: Tighten cover bolts uniformly.


VALSTEAM ADCA We reserve the right to change the design and material of this product without notice.
IMI 1.381 E 05.14
PARTS LIST FOR FLT32HC STEAM TRAPS DN 1”, DN25
TRAP SIZE
DN
A.92.2502.025 Valve, seat, float & gasket D.P.4,5bar DN1” 3, 4, 5, 6, 7 1Set
A.92.2503.025 Valve, seat, float & gasket D.P.10 bar DN1” 3, 4, 5, 6, 7 1Set
A.92.2504.025 Valve, seat, float & gasket D.P.14 bar DN1” 3, 4, 5, 6, 7 1Set
A.92.2505.025 Valve, seat, float & gasket D.P.21 bar DN1” 3,4,5,6,7 1Set
A.92.2502.125 Float & gasket DN1” 3, 7 1 Set
A.92.2502.225 Air vent & gasket DN1” 3, 8 1 Set
CODE
DESIGNATION
QTY.
POS.NR.
Recommended tightening torques FLT32HC DN 1”, DN25
TRAP SIZE
DN
4 1” 50±5
8 1” 50±5
9 1” 80±5
POS.NR.
Nm
Remarks: Tighten cover bolts uniformly.
PARTS LIST FOR FLT32 STEAM TRAPS DN 11/2”-2”, DN40-50
TRAP SIZE
DN
A.92.2502.040 Valve, seat, float & gasket D.P.4,5bar DN11/2”-2” 3, 4, 5, 6, 7 1Set
A.92.2503.040 Valve, seat, float & gasket D.P.10 bar DN11/2”-2” 3, 4, 5, 6, 7 1Set
A.92.2504.040 Valve, seat, float & gasket D.P.14 bar DN11/2”-2” 3, 4, 5, 6, 7 1Set
A.92.2505.040 Valve, seat, float & gasket D.P.21 bar DN11/2”-2” 3, 4, 5, 6, 7 1Set
A.92.2502.140 Float & gasket DN11/2”-2” 3, 7 1Set
A.92.2502.240 Air vent & gasket DN11/2”-2” 3, 8 1Set
CODE
DESIGNATION
QTY.
POS.NR.
Recommended tightening torques FLT32 DN 11/2”-2”, DN 40-50
TRAP SIZE
DN
4 DN11/2”-2”10-15 (4xM6)
8 DN11/2”-2”50±5
9 DN11/2”-2”85±5
POS.NR.
Nm
Remarks: Tighten cover bolts uniformly.


VALSTEAM ADCA We reserve the right to change the design and material of this product without notice.
IMI 1.381 E 05.14
Correct Installation Wrong Installation
PRODUCTS RETURNING
- Information regarding any hazards and precautions to be considered because of contaminating fluids and
residues or mechanical damage that may represent a health, safety or environmental risk, must be provided in
writing by the distributors and costumers when returning products to Valsteam ADCA engineering.
- Health and safety data sheets regarding substances identified as hazardous or potentially hazardous must be
provided with the information mention above.
- LOSS OF WARRANTY: Total or partial disregard of above instructions involves loss of any right to warranty.