V&A VA8051 Series User manual

-1-
LIGHT INTENSITY METER
SERIES
VA8051
Users Manual

-2-
Contents
1. Introduction.................................................. 3
2. Features........................................................ 5
3. Names of parts ............................................. 7
4. Operation instruction.................................... 9
5. Keys instruction.......................................... 11
6. Reference table of illumination standard ..... 13
7. Maintenance............................................... 14

-3-
1. Introduction
Thank you for purchasing the light intensity meter series
from us. The product includes two type: Type A(Basic),
Type B(Light sensor can be rotated in 270°to make
measure more easy and fast). Please take a few
minutes to browse through this user manual before you
begin to operate the meter to ensure that you are fully
familiarized with how best to operate the meter as
accurately and safely as possible.
This meter is an illuminance measuring instrument. It is

-4-
normally used to measure illuminances, e.g.at
workplaces.
1.1 Precautions safety measures
To get the best service from this meter, please read
this user's manual carefully and observe the detailed
safety precautions strictl y.
1.1.1 During use
1. If the OL symbol will show on the LCD, it means the
readings is outside the measuring range. Please keep
to the permitted measuring range.
2. Never store the product together with solvents, acides
or other aggressive substances.
3. When the battery voltage is under proper operation
requirement, the symbol will show on the LCD and
the battery need to be replaced with new.
1.1.2 Maintaining the product
Do not measure at a high temperature, high
humidity places.
Keep the light sensor clean.

-5-
To guarantee correct readings: Hold the
instrument horizontally so that the light sensor is
directed upwards.
When not using the instrument for a long time,
please remove the battery and avoid storing in
high temperature and high humidity.
2. Features
1. Display: 6 digits LCD Display
2. Parameters：
Lux（lm/m2）
foot candle (lm/ft2)
3. Resolution: 1 Lux（0…30000 Lux）；
0.1 ftc（0…2788.0 ftc）；
4. Range: 0…30000 Lux
0…2788.0 ftc
5. Accuracy: ±(4% +50 digits) to reference

-6-
6. Sample rate: 2 time /sec
7. auto power off: about 20 minutes
8. low battery indicator
9. Operating environment:
0℃~ 50 ℃(32℉~122℉)，0 ~ 80%RH
10. Storage environment:
-20℃~ 60℃(-4℉~140℉)，0 ~ 80%RH
11. Dimension and Weight:
121(L)x60(W)x30(H)mm, about 180g
12. Accessories:
DC1.5V (AAA) x 3pcs
String x 1pcs
Plastic box x 1pcs
Users manual x 1pcs

-7-
3. Names of parts
Instrument Familiarization
1. Sensor cover
2. Light sensor
（270°adjustable only for type B）
3. LCD display
4. Function key
Unit Func.
ON/OFF
Light intensity meter

-8-
LCD Display
The meaning of the symbols represented by the
following table
Number
of Order Symbol Functions
1
Indicating it is now in
the data-holding mode
2
Indicating the display
value being the
maximum value(MAX)
3
Indicating the display
value being the

-9-
minimum value(MIN)
4 Measure values
5 parameter unit
6 parameter unit
7
Indication to the
calibration mode
8
Indication low power of
batteries.
Batteries should be
replaced.
4. Operation instruction
1. Please install new batteries on the meter .
2. Put the meter on the environment to be measured
and hold it horizontally so that the light sensor is
directed upwards.
3. Press the ON/OFF key to turn the power on.

-10-
4. After power on, press the Unit key to select the
needed units.
5. When the reading has been stable, read the
illumination value.
* If you still need more operations, please see the
description of keys instruction.

-11-
5.Keys instruction
1. ON/OFF key
Press the key to turn the power ON and press the key
once more to turn the power OFF.
2. Func. key
Press the key can select the state of MAX、MIN、
HOLD.
The cycle of views shows as following figure:
Measure mode Hold mode Max mode
Min mode
Hold mode: Reading are held.
Max mode: Maximum values since the instrument
Mode
key
Mode
key
Mode key Mode key

-12-
was last switched on or last reset.
Min mode: Minimum values since the instrument
was last switched on or last reset.
3. Unit key
1) Unit set
Press the key can change the parameter unit: lux, ftc.
2) Back light contrl
If press the key >2sec. the back light will be turned on,
Press the key once >2sec. the light will be turned off. If
the back light is not closed within 60 seconds, it will be
turned off automatically.
3) Auto power off set
When the meter is powered on, it is under auto
power off mode. The meter will power itself off after 20
minutes if no key operation.
Canceled auto power off function: press Unit key
when power on until the LCD display AP OFF, then
press the ON/OFF key to confirm the setting. And then
the meter will be power off.

-13-
6. Reference table of
illumination standard
Place
Illumination
- Office
Conference Room,
Living room
200 ~ 750
Administration
700 ~ 1,500
Typing
1000 ~ 2,000
- Factory
Packaging, Access
150 ~ 300
Assembly line
300 ~ 750
Check
750 ~ 1,500
Electronic components
assembly line
1,500 ~ 3,000
- Hotel
Public places,Lavatory
100 ~ 200
Reception room
200 ~1,000
- Store
Staircase, corridor
150 ~ 200
Presentation window,
Packaging station
750 ~ 1,500
Shop window
1,500 ~ 3,000
- Hospital

-14-
Ward, Warehouse
100 ~ 200
Medical examination
room
300 ~ 750
Operating room,
Emergency Room
750 ~ 1,500
- School
Hall, Indoor stadium,
Classroom
200 ~ 750
Laboratory,Library
500 ~ 1,500
7.Maintenance
1. CLEANING INSTRUCTIONS
The meter may be wiped down with a wet sponge or
cloth using a mild water based detergent or
anti-bacterial soap and rinsed under a gentle stream
of cold water.
NOTE:
This unit is not designed for complete submersion or

-15-
washing in water.
2. BATTERY REPLACEMENT
Use the following procedure:
When the battery voltage drop below proper operation
range the symbol will appear on the LCD display
and the battery need to be replaced.
Press the battery cover and towards arrowhead
direction to open the battery cover.
Replace the battery with three new 1.5V batteries
(AAA).
Replace the battery cover.

-16-
V
A8051-09