Vanguard Vp5c Quick start guide

Save this manual for future reference.

INFRARED VENT-FREE PROPANE/LP GAS

HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

Models:VP5C and VP10

WARNING: If the information in this manual is not followed exactly, a fire or

explosion may result causing property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediatelycallyourgassupplierfromaneighbor’sphone.Followthegas

supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

— Installation and service must be performed by a qualified installer, service

agency, or the gas supplier.

WARNING: This is an unvented gas-fired heater. It uses air (oxygen) from the

room in which it is installed. Provisions for adequate combustion must be

provided. Refer to page 3 of this manual.

Thisappliance maybe installedin anaftermarket* manufactured(mobile) home,

where not prohibited by state or local codes.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

This appliance is only for use with the type of gas indicated on the rating plate.

This appliance is not convertible for use with other gases.

101850

PROPANE/LP GAS HEATERS

VANGUARD VP5C AND VP10

Carbon Monoxide Poisoning: Early

signs of carbon monoxide poisoning re-

semble the flu, with headaches, dizziness,

ornausea.Ifyouhavethesesigns,theheater

maynot beworking properly.Getfreshair

atonce!Haveheaterserviced.Somepeople

are more affected by carbon monoxide than

others.Theseincludepregnantwomen,per-

sons with heart or lung disease or anemia,

those under the influence of alcohol, and

those at high altitudes.

Propane/LPGas:Propane/LPgasisodor-

less. An odor-making agent is added to

propane/LP gas. The odor helps you detect

a propane/LP gas leak. However, the odor

addedtopropane/LPgascanfade.Propane/

LP gas may be present even though no odor

exists.

Make certain you read and understand all

Warnings. Keep this manual for reference.

It is your guide to safe and proper operation

of this heater.

1. This appliance is only for use with the

typeofgas indicated on the rating plate.

Thisapplianceisnot convertible for use

with other gases.

2. Do not place propane/LP supply tank(s)

inside any structure. Locate propane/

LP supply tank(s) outdoors.

SAFETY

INFORMATION

WARNINGS

IMPORTANT: Read this Owner’s

Manual carefully and completely

before trying to assemble, oper-

ate, or service this heater. Im-

proper use of this heater can

causeseriousinjuryordeathfrom

burns, fire, explosion, and car-

bon monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

WARNING:Anychangetothis

heateror itscontrols canbe dan-

gerous.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch;

do not use any phone in your build-

ing

• immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions

• ifyou cannot reach your gas supplier,

call the fire department

4. Heater model VP10 shall not be in-

stalled in a bathroom.

5. Never install the heater

• in a recreational vehicle

• wherecurtains,furniture, clothing, or

otherflammable objects are less than

36inches from the front, top, or sides

of the heater

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

6. Always run heater with control knob

at LOW or HIGH locked positions

(VP10) or ON position (VP5C). Never

set control knob between locked posi-

tions. Poor combustion may result.

7. This heater needs fresh, outsideair ven-

tilation to run properly.This heater has

an oxygen depletion sensor (ODS) pi-

lot light safety system. The ODS shuts

down the heater if not enough fresh air

is available. See Air for Combustion

and Ventilation, pages 3 through 5.

8. Keep all air openings in the front and

bottom of heater clear and free of de-

bris. This will insure enough air for

proper combustion.

9. If heater shuts off, do not relight until

you provide fresh, outside air. If heater

keeps shutting off, have it serviced.

10. Do not run heater

• where flammable liquids or vapors

are used or stored

• under dusty conditions

11. Never place any objects on the heater.

12. Surface of heater becomes very hot

whenrunningheater.Keepchildrenand

adults away from hot surface to avoid

burns or clothing ignition. Heater will

remain hot for a time after shut-down.

Allow surface to cool before touching.

13. Carefully supervise young children

when they are in same room with

heater.

14. Make sure grill guard is in place be-

fore running heater.

15. Do not use heater if any part has been

under water. Immediately call a quali-

fied service technician to inspect the

room heater and to replace any part of

the control system and any gas control

which has been under water.

16. Turn off heater and let cool before ser-

vicing. Only a qualified service person

should service and repair heater.

17. Operating heater above elevations of

4,500 feet could cause pilot outage.

18. To prevent performance problems, do

not use propane fuel tank of less than

100 lb. capacity.

101850

OWNER’S MANUAL

PRODUCT

IDENTIFICATION

PRODUCT

FEATURES

SAFETY PILOT

This heater has a pilot with an Oxygen

Depletion Sensor Shutoff System (ODS).

TheODS/pilotisarequiredfeatureforvent-

free room heaters. The ODS/pilot shuts off

the heater if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system

requires no matches, batteries, or other

sources to light heater.

LOCAL CODES

Install and use heater with care. Follow all

local codes. In the absence of local codes,

use the latest edition of National Fuel Gas

Code ANSI Z223.1, also known as NFPA

54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

UNPACKING

1. Remove heater from carton.

2. Remove all protective packaging ap-

plied to heater for shipment.

3. Check heater for any shipping damage.

If heater is damaged, promptly inform

dealer where you bought heater.

Heater Cabinet

Grill Guard

Burners

Front Panel

Figure 1 - Vent-Free Propane/LP Gas Heater (Model VP10 Shown)

Control Knob

Piezo Ignitor Button

AIR FOR

COMBUSTION

AND

VENTILATION

WARNING: This heater shall

not be installed in a confined

spaceunlessprovisions arepro-

vided for adequate combustion

and ventilation air. Read the fol-

lowing instructions to insure

properfreshairforthisandother

fuel-burning appliances in your

home.

Today’s homes are built more energy effi-

cient than ever. New materials, increased

insulation, and new construction methods

help reduce heat loss in homes. Home own-

ersweatherstripandcaulkaroundwindows

and doors to keep the cold air out and the

warm air in. During heating months, home

owners want their homes as airtight as pos-

sible.

While it is good to make your home energy

efficient,yourhomeneedstobreathe.Fresh

air must enter your home. All fuel-burning

appliances need fresh air for proper com-

bustion and ventilation.

Exhaustfans,fireplaces,clothesdryers,and

fuel burning appliances draw air from the

house to operate. You must provide ad-

equate fresh air for these appliances. This

will insure proper venting of vented fuel-

burning appliances.

PROVIDING ADEQUATE

VENTILATION

ThefollowingisexerptsfromNationalFuel

Gas Code. NFPA 54/ANSI Z223.1, Section

5.3, Air for Combustion and Ventilation.

Allspacesinhomesfallintooneofthethree

following ventilation classifications:

1. Unusually Tight Contruction; 2. Uncon-

fined Space; 3. Confined Space.

The information on pages 4 and 5 will help

you classify your space and provide ad-

equate ventilation.

101850

PROPANE/LP GAS HEATERS

VANGUARD VP5C AND VP10

DETERMINING FRESH-AIR

FLOW FOR HEATER

LOCATION

Determining if You Have a

Confined or Unconfined Space

Usethisworksheetto determineif youhave

a confined or unconfined space.

Space: Includes the room in which you

will install heater plus any adjoining rooms

with doorless passageways or ventilation

grills between the rooms.

1. Determine the volume of the space

(length x width x height).

Length x Width x Height =

______ cu. ft. (volume of space)

Example:

Space size

20 ft. (length) x 16 ft. (width) x 8 ft.

(ceiling height) =

2560 cu. ft. (volume of space)

If additional ventilation to adjoining

room is supplied with grills or open-

ings, add the volume of these rooms to

the total volume of the space.

2. Divide the space volume by 50 cubic

feet to determine the maximum Btu/

Hr the space can support.

_____(volume of space) ÷50 cu. ft. =

(Maximum Btu/Hr the space can sup-

port)

Example:

2560 cu. ft. (volume of

space) ÷50 cu. ft. = 51.2 or 51,200

(maximum Btu/Hr the space can sup-

port)

Unusually Tight Construction

The air that leaks around doors and win-

dows may provide enough fresh air for

combustion and ventilation. However, in

buildings of unusually tight construction,

you must provide additional fresh air.

Unusually tight construction is

defined as construction where:

a. walls and ceilings exposed to

the outside atmosphere have a

continuous water vapor retarder

with a rating of one perm (6x10-11

kg per pa-sec-m2) or less with

openingsgasketedorsealed

and

b. weather stripping has been

addedonopenablewindowsand

doors

and

c. caulking or sealants are ap-

plied to areas such as joints

aroundwindowanddoorframes,

between sole plates and floors,

between wall-ceiling joints, be-

tweenwallpanels,atpenetrations

for plumbing, electrical, and gas

lines, and at other openings.

If your home meets all of the three

criteria above, you must provide ad-

ditional fresh air. See

Ventilation Air

From Outdoors

, page 5

If your home does not meet all of the

three criteria above, proceed to

De-

termining Fresh-Air Flow For Heater

Location.

AIR FOR

COMBUSTION

AND

VENTILATION

Continued

Confined and Unconfined Space

TheNationalFuelGasCode(ANSIZ2123.1,

1992 Section 5.3) defines a confined space

as a space whose volume is less than 50

cubicfeetper1,000Btuperhour(4.8m3per

kw) of the aggregate input rating of all

appliances installed in that space and an

unconfined space as a space whose volume

is not less than 50 cubic feet per 1,000 Btu

per hour (4.8 m3 per kw) of the aggregate

inputratingofallappliancesinstalledinthat

space.Roomscommunicating directly with

the space in which the appliances are in-

stalled*, through openings not furnished

with doors, are considered a part of the

unconfined space.

*Adjoiningroomsarecommunicatingonly

iftherearedoorlesspassagewaysorventila-

tion grills between them.

3. Add the Btu/Hr of all fuel burning ap-

pliances in the space.

Vent-free heater _________ Btu/Hr

Gas water heater*________ Btu/Hr

Gas furnace ____________ Btu/Hr

Vented gas heater ________ Btu/Hr

Gas fireplace logs________ Btu/Hr

Other gas

appliances* + ___________ Btu/Hr

Total = ________________ Btu/Hr

Example:

Gas water heater

40,000 Btu/Hr

Vent-free heater +10,000 Btu/Hr

Total = 50,000 Btu/Hr

* Do not include direct-vent gas appli-

ances. Direct-vent draws combustion

air from the outdoors and vents to the

outdoors.

4. Compare the maximum Btu/Hr the

space can support with the actual

amount of Btu/Hr used.

__________ Btu/Hr (maximum the

space can support)

__________ Btu/Hr (actual amount of

Btu/Hr used)

Example:

46,100 Btu/Hr (maximum

the space can support)

50,000 Btu/Hr (actual

amount of Btu/Hr used)

The space in the above example is a con-

fined space because the actual Btu/Hr used

ismorethanthemaximumBtu/Hrthespace

can support. You must provide additional

fresh air. Your options are as follows:

A. Reworkworksheet, adding the space of

an adjoining room. If the extra space

provides an unconfined space, remove

door to adjoining room or add ventila-

tion grills between rooms. See Ventila-

tion Air From Inside Building, page 5.

B. Vent room directly to the outdoors. See

Ventilation Air From Outdoors, page 5.

C. Install a lower Btu/Hr heater, if lower

Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the

maximumBtu/Hrthespacecansupport,the

spaceisanunconfinedspace.Youwillneed

no additional fresh air ventilation.

101850

OWNER’S MANUAL

AIR FOR

COMBUSTION

AND

VENTILATION

Continued

Remove

Door into

Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Ventilation

Grills

into Adjoining

Room,

Option 1

WARNING:Iftheareainwhich

the heater may be operated is

smaller than that defined as an

unconfined space, provide ad-

equate combustion and ventila-

tion air by one of the methods

described in the

National Fuel

Gas Code, ANSI Z223.1, 1992,

Section 5.3 or applicable local

codes.

VENTILATION AIR

Ventilation Air From Inside

Building

Thisfreshairwouldcomefromanadjoining

unconfined space. When ventilating to an

adjoining unconfined space, you must pro-

vide two permanent openings: one within

12" of the ceiling and one within 12" of the

floor on the wall connecting the two spaces

(seeoptions1and2,Figure2).Youcanalso

remove door into adjoining room (see op-

tion 3, Figure 2). Follow the National Fuel

Gas Code NFPA 54/ANSI Z223.1, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

WARNING:Rework

worksheet, adding the space of

the adjoining unconfined space.

Thecombinedspacesmusthave

enough fresh air to supply all

appliances in both spaces.

Figure 2 - Ventilation Air from Inside Building

Figure 3 - Ventilation Air from Outdoors

Outlet

Air Ventilated

Attic

Outlet

Air

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

Ventilation Air From Outdoors

Provideextrafreshairbyusingventilation grillsorducts.Youmustprovidetwopermanent

openings:onewithin12"oftheceilingandonewithin12"ofthefloor.Connecttheseitems

directlytotheoutdoorsorspacesopentotheoutdoors.Thesespacesincludeatticsandcrawl

spaces.

IMPORTANT:

Do not provide openings for inlet or outlet air into attic if attic has a

thermostat-controlledpower vent.Heatedair enteringtheattic willactivatethe powervent.

101850

PROPANE/LP GAS HEATERS

VANGUARD VP5C AND VP10

2. Mark two mounting screw locations on

wall (see Figure 5).

INSTALLING HEATER TO

WALL

Marking Screw Locations

1. Determine where you will locate heater.

Figure 5 - Mounting Screw Locations

WARNING:Maintainminimum

clearances shown in Figure 5. If

you can, provide greater clear-

ancesfromfloorandjoiningwall.

Figure4-MountingClearancesAsViewed

From Front of Heater

Forconvenienceandefficiency,installheater

• where there is easy access for opera-

tion, inspection, and service

• in coldest part of room

36"

FLOOR

CEILING

Minimum

Minimum To Top Surface

Of Carpeting, Tile Or Other

Combustible Material

Minimum

From

Sides Of

Heater

Right

Side

Left

Side

INSTALLING

TO WALL

NOTICE: A qualified service per-

son must install heater. Follow

all local codes.

CHECK GAS TYPE

Useonlypropane/LPgas.Ifyourgassupply

isnotpropane/LP,donotinstallheater.Call

dealer where you bought heater for proper

type heater.

INSTALLATION ITEMS

Beforeinstallingheater,makesureyouhave

the items listed below.

• externalregulator(suppliedbyinstaller,

see page 8)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• manual shutoff valve *

• ground joint union

• test gauge connection * (see Figure 13,

page 8)

• sediment trap

• tee joint

• pipe wrench

LOCATING HEATER

This heater is designed to be mounted on a

wall.

WARNING:Maintainthemini-

mumclearancesshowninFigure

4.Ifyoucan,providegreaterclear-

ancesfromfloor,ceiling,andjoin-

ing wall.

WARNING: Never install the

heater

• in a bathroom (VP10 only)

• in a recreational vehicle

• where curtains, furniture,

clothing,orotherflammable

objects are less than 36

inchesfromthefront,top,or

sides of the heater

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities in the air (such

as tobacco smoke) exist, may

discolor walls.

* AnA.G.A.design-certifiedmanualshutoff

valve with 1/8" NPT tap is an acceptable

alternative to test gauge connection. The

optional A.G.A. design-certified manual

shutoff valve can be purchased from your

dealer. See Accessory, page 15.

CAUTION: If you install the

heater in a home garage

• heater pilot and burner must

be at least 18 inches above

floor

• locate heater where moving

vehicle will not hit it

IMPORTANT:

Vent-freeheatersaddmois-

ture to the air. Although this is beneficial,

installing heater in rooms without enough

ventilation air may cause mildew to form

from too much moisture. See Fresh Air for

Combustion and Ventilation, pages 3

through 5.

Mounting

Screw

Locations

10 7/8"

Minimum To

Maintain 8"

Clearance

From Wall

7 3/4"

20 1/4"

Minimum To

Maintain 3"

Clearance

From Floor

FLOOR

JOINING WALL

101850

OWNER’S MANUAL

Installing Two Mounting Screws

Note:

Wall anchors and mounting screws

areinhardwarepackage.Thehardwarepack-

age is provided with heater.

Attaching to wall stud method

For attaching mounting screw to wall stud

1. Drill hole at marked location using 9/

64" drill bit.

2. Insert mounting screw into wall stud.

3. Tighten screw until 1/16" space (thick-

ness of penny) is between screwhead

and wall.

Attaching to wall anchor

method

Follow instructions below to attach mount-

ing screws to hollow walls (wall areas be-

tween studs) or solid walls (concrete or

masonry).

1. Drill holes at marked locations using

5/16"drill bit. For solid walls (concrete

or masonry), drill at least 1 1/4" deep.

2. Fold wall anchor (see Figure 6).

Figure 8 - Tightening Anchors

5. Tighten two screws until 1/16" space

(thickness of penny) is between

screwheads and wall (see Figure 8).

Figure 7 - Popping Open Anchor Wings

For Thin Walls

Thin Walls

(1/4" to 1/2" thick)

3. Insert wall anchor (wings first) into

hole. Tap anchor flush to wall.

4. For thin walls (1/2" or less), insert red

key into wall anchor. Push red key to

“pop” open anchor wings (see Figure

7).

IMPORTANT:

Donot hammer key!

Forthickwalls(over1/2"thick)orsolid

walls, do not pop open wings.

Figure 6 - Folding Anchor

Thin or Thick

Wall (thick

wall shown)

Solid

Wall

1/16"

Space

INSTALLING

TO WALL

Continued

Placing Heater On Mounting

Screws

1. Locate two keyhole slots on back panel

of heater (see Figure 9).

2. Place large openings of slots over

screwheads. Slide heater down until

screws are in small portion of slots.

Figure 11 - Installing Bottom Mounting

Screw

Figure 9 - Location Of Keyhole Slots On

Back Panel Of Heater

Keyhole Slots

Removing Front Panel Of Heater

1. Remove two screws near bottom cor-

ners of front panel.

2. Lift straight up on grill guard until it

stops.Grillguard will slide upabout1/4".

3. Pull bottom of front panel forward, then

down.

Figure 10 - Removing Front Panel Of

Heater

Installing Bottom Mounting

Screw

1. Locate bottom mounting hole. This

hole is near bottom on back panel of

heater (see Figure 11).

2. Mark screw location on wall.

3. Remove heater from wall.

4. If installing bottom mounting screw

into hollow or solid wall, install wall

anchor. Follow steps 1 through 5 under

Attaching To Wall Anchor Method.

If installing bottom mounting screw

into wall stud, drill hole at marked lo-

cation using 9/64" drill bit.

5. Replace heater on wall.

6. Insert bottom anchor screw through

backpanelintobottomanchorordrilled

hole (see Figure 11).

7. Tighten screw until heater is firmly se-

cured to wall. Do not over tighten.

Note:

Do not replace front panel at this

time. Replace front panel after making

gas connections and checking for leaks

(see pages 8 and 9).

101850

PROPANE/LP GAS HEATERS

VANGUARD VP5C AND VP10

IMPORTANT:

Hold pressure regulator

with wrench when connecting it to gas pip-

ing and/or fittings.

Figure 13 - Gas Connection

* An A.G.A. design-certified manual shutoff valve with 1/8" NPT tap is an acceptable

alternative to test gauge connection. Purchase the optional A.G.A. design-certified manual

shutoff valve from your dealer. See Accessory, page 15.

CONNECTING

TO GAS

SUPPLY

NOTICE: A qualified service per-

son must connect heater to gas

supply. Follow all local codes.

The installer must supply an external regu-

lator. The external regulator will reduce

incoming gas pressure. You must reduce

incominggaspressuretobetween11and14

inchesofwater.Ifyoudonotreduceincom-

ing gas pressure, heater regulator damage

could occur. Install external regulator with

the vent pointing down as shown in Figure

12. Pointing the vent down protects it from

freezing rain or sleet.

CAUTION: Never connect

heaterdirectlyto thepropane/LP

supply. This heater requires an

externalregulator(notsupplied).

Install the external regulator be-

tweentheheaterandpropane/LP

supply.

Installsedimenttrapinsupplylineasshown

in Figure 13. Locate sediment trap where it

is within reach for cleaning. Locate sedi-

menttrap where trapped matter is not likely

to freeze. A sediment trap traps moisture

and contaminants. This keeps them from

going into heater controls. If sediment trap

is not installed or is installed wrong, heater

may not run properly.

Installation must include a manual shutoff

valve,ground joint union, and plugged1/8"

NPT tap. Locate NPT tap within reach for

test gauge hook up. NPT tap must be up-

stream from heater (see Figure 13).

Apply pipe joint sealant lightly to male

threads. This will prevent excess sealant

fromgoingintopipe. Excess sealant in pipe

could result in clogged heater valves.

Figure 12 - External Regulator With Vent

Pointing Down

CAUTION: Use only new,

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

your local codes. Use pipe 3/8"

diameter or greater to allow

proper gas volume to heater. If

pipe is too small, undue loss of

pressure will occur.

Propane/LP

Supply Tank

Vent

Pointing

Down

External

Regulator

CAUTION:Usepipejointseal-

ant that is resistant to liquid pe-

troleum (LP) gas.

Tee Joint

Reducer

Bushing to

1/8" NPT

Plug Tap

Test

Gauge

Connection *

Tee

Joint

Pipe

Nipple

Cap

Pressure

Regulator

3/8" NPT

Pipe Nipple

Heater

Cabinet

Ground Joint

Union

From External

Regulator

(11" W.C. to 14" W.C.

Pressure)

Manual Shutoff

Valve *

3" Minimum Sediment

Trap

Closed

101850

OWNER’S MANUAL

CHECKING GAS

CONNECTIONS

PRESSURE TESTING GAS

SUPPLY PIPING SYSTEM

Test Pressures In Excess Of 1/2

PSIG

1. Disconnect heater and its individual

manual shutoff valve from gas supply

piping system. Pressures in excess of

1/2 PSIG will damage heater regula-

tor.

2. Cap off open end of gas pipe where

manual shutoff valve was connected.

WARNING: Test all gas pip-

ing and connections for leaks

after installing or servicing. Cor-

rect all leaks at once.

WARNING:Neveruseanopen

flame to check for a leak. Apply a

mixture of liquid soap and water

to all joints. Bubbles forming

show a leak. Correct all leaks at

once.

CAUTION: Make sure exter-

nal regulator has been installed

between propane/LP supply and

heater.Seeguidelinesunder

Con-

necting to Gas Supply

, page 8.

3. Pressurize supply piping system by ei-

ther using compressed air or opening

propane/LP supply tank valve.

4. Check all joints of gas supply piping

system. Apply mixture of liquid soap

and water to gas joints. Bubbles form-

ing show a leak.

5. Correct all leaks at once.

Test Pressures Equal To or

Less Than 1/2 PSIG

1. Close manual shutoff valve (see Fig-

ure 14).

2. Pressurize supply piping system by ei-

ther using compressed air or opening

propane/LP supply tank valve.

POSITION

OFF

POSITION

Figure 14 - Manual Shutoff Valve

Manual

Shutoff

Valve

Open

Closed

3. Check all joints from propane/LP sup-

ply tank to manual shutoff valve (see

Figure 15). Apply mixture of liquid

soap and water to gas joints. Bubbles

forming show a leak.

4. Correct all leaks at once.

PRESSURE TESTING

HEATER GAS

CONNECTIONS

1. Open manual shutoff valve (see Figure

14).

2. Open propane/LP supply tank valve.

3. Make sure control knob of heater is in

the OFF position.

4. Check all joints from manual shutoff

valve to control valve (see Figure 15).

Apply mixture of liquid soap and wa-

ter to gas joints. Bubbles forming show

a leak.

5. Correct all leaks at once.

6. Light heater (see Operating Heater,

pages 9 through 11). Check all other

internal joints for leaks.

7. Turn off heater (see To Turn Off Gas to

Appliance, page 10).

8. Replace front panel.

Figure 15 - Checking Gas Joints

Propane/LP

Supply Tank

Manual

Shutoff

Valve

Control

Valve

Location

OPERATING

HEATER

FOR YOUR SAFETY

READ BEFORE

LIGHTING

WARNING: If you do not fol-

low these instructions exactly, a

fireorexplosionmayresultcaus-

ing property damage, personal

injury or loss of life.

A. This appliance has a pilot which must

be lighted by hand. When lighting the

pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around

the appliance area for gas. Be sure to

smell next to the floor because some

gas is heavier than air and will settle

on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• Ifyoucannotreach your gas supplier,

call the fire department.

C. Use only your hand to push in or turn

the gas control knob. Never use tools.

If the knob will not push in or turn by

hand, don’t try to repair it, call a quali-

fied service technician or gas supplier.

Force or attempted repair may result in

a fire or explosion.

D. Do not use this appliance if any part

has been under water. Immediately call

aqualified service technician to inspect

the appliance and to replace any part

of the control system and any gas con-

trol which has been under water.

101850

PROPANE/LP GAS HEATERS

VANGUARD VP5C AND VP10

TO TURN OFF GAS

TO APPLIANCE

TO SELECT HEATING

LEVEL

Figure 18 - Burner Patterns

1. Slightly press in control knob and turn

counterclockwise

C-clockwise

to the LOW

or HIGH positions (VP10) or ON po-

sition (VP5C).

IMPORTANT:

Release downward

pressure while turning control knob.

Control knob will lock at the desired

position.

LOW

OFF

PILOT

HIGH

OFF

PILOT

OFF

Control VP10

Knob Burners

Control VP5C

Knob Burner

WARNING: When running

heater, set control knob at LOW

or HIGH locked positions (VP10)

or ON position (VP5C). Never set

control knob between locked

positions. Poor combustion and

higher levels of carbon monox-

ide may result.

CAUTION:Donottrytoadjust

heating levels by using the

manual shutoff valve.

OFF

PILOT

OFF

4. Wait five (5) minutes to clear out any

gas. Then smell for gas, including near

the floor. If you smell gas, STOP! Fol-

low “B” in the safety information, col-

umn 3, page 9. If you don’t smell gas,

go to the next step.

5. Press in control knob, and turn coun-

terclockwise

C-clockwise

to pilot position.

Keep control knob pressed for five sec-

onds.

Note:

You may be running this heater

for the first time after hooking up to

gas supply. If so, the control knob

may need to be pressed in for 30 sec-

onds. This will allow air to bleed

from the gas system.

• If control knob does not pop up

when released, contact a qualified

service person or gas supplier for

repairs.

6. With control knob pressed in, push

down and release ignitor button. This

will light pilot. The pilot is attached to

the front of burner. If needed, keep

pressingignitor button until pilot lights.

Note:

If pilot does not light, refer to

Troubleshooting, pages 12 through 14.

OPERATING

HEATER

Continued

Ignitor Electrode

Pilot Burner

Thermocouple

Figure 17 - Pilot

Control Knob

Figure 16 - Control Knob In The OFF

Position (Model VP10 Shown)

LIGHTING

INSTRUCTIONS

1. STOP! Read the safety information

above.

2. Make sure manual shutoffvalve is fully

open.

3. Turn control knob clockwise

Clockwise

to the OFF position.

Ignitor Button

OFF

PILOT

IGNITOR

LOW

HIGH

Also contact a qualified service per-

son or gas supplier for repairs. Until

repairs are made, light pilot with

match, see Manual Lighting Proce-

dure, page 11.

7. Keep control knob pressed in for 10

seconds after lighting pilot. After 10

seconds, release control knob.

Note:

If pilot goes out, repeat steps

3 through 7.

Shutting Off Heater

1. Turn control knob clockwise

Clockwise

to the OFF position.

Shutting Off Burner Only (pilot

stays lit)

1. Turn control knob clockwise

Clockwise

to the PILOT position.

101850

OWNER’S MANUAL

INSPECTING

BURNER

Check pilot flame pattern and burner flame

pattern often.

PILOT FLAME PATTERN

Figure 19 shows a correct pilot flame pat-

tern. Figure 20 shows an incorrect pilot

flame pattern. The incorrect pilot flame is

not touching the thermocouple. This will

cause the thermocouple to cool. When the

thermocouple cools, the heater will shut

down.

OPERATING

HEATER

Continued

1. Remove front panel (see Figure 10,

page 7).

2. Follow steps 1 through 5 under Light-

ing Instructions, page 10.

3. With control knob pressed in, strike

match. Hold match to pilot until pilot

lights.

4. Keep control knob pressed in for 10

seconds after pilot is lit. After 10 sec-

onds, release control knob.

5. Replace front panel.

Thermocouple

Figure 20 - Incorrect Pilot Flame Pattern

Figure 19 - Correct Pilot Flame Pattern

Thermocouple

GRH/OV 008BAD PILOT/LP

If pilot flame pattern is incorrect, as shown

in Figure 20

• turn heater off (see To Turn Off Gas

to Appliance, page 10)

• see Troubleshooting, pages 12

through 14

GRH/OV 007GOOD PILOT/LP

Pilot Burner

MANUAL LIGHTING

PROCEDURE BURNER FLAME PATTERN

Figure 21 shows a correct burner flame

pattern.Figure22showsanincorrectburner

flame pattern.

Figure 21 - Correct Burner Flame Pattern

(Model VP10 Shown)

Figure22-IncorrectBurnerFlamePattern

(Model VP10 Shown)

Ifburnerflamepatternisincorrect,asshown

in Figure 22

• turn heater off (see To Turn Off Gas

to Appliance, page 10)

• see Troubleshooting, pages 12

through 14

CLEANING AND

MAINTENANCE

ODS/PILOT AND BURNER

ORIFICE

• Use a vacuum cleaner, pressurized

air, or small, soft bristled brush to

clean.

CABINET

Air Passageways

• Use a vacuum cleaner or pressurized

air to clean.

Exterior

• Use a soft cloth dampened with a

mild soap and water mixture. Wipe

the cabinet to remove dust.

WARNING: Turn off heater

and let cool before cleaning.

CAUTION: You must keep

control areas, burner, and circu-

lating air passageways of heater

clean. Inspect these areas of

heater before each use. Have

heaterinspectedyearlybyaquali-

fied service person. Heater may

needmorefrequentcleaningdue

to excessive lint from carpeting,

bedding material, etc.

101850

PROPANE/LP GAS HEATERS

VANGUARD VP5C AND VP10

TROUBLESHOOTING

Note:

All troubleshooting items

are listed in order of operation.

WARNING: Turn off heater and let cool before servicing. Only a

qualified service person should service and repair heater.

CAUTION: Never use a wire, needle, or similar object to clean ODS/

pilot. This can damage ODS/pilot unit.

POSSIBLE CAUSE

1. Ignitor electrode positioned wrong

2. Ignitor electrode broken

3. Ignitor electrode not connected to ig-

nitor cable

4. Ignitor cable pinched or wet

5. Piezo ignitor nut is loose

6. Broken ignitor cable

7. Bad piezo ignitor

1. Gas supply turned offormanualshutoff

valve closed

2. Control knob not in PILOT position

3. Control knob not pressed in while in

PILOT position

4. Air in gas lines when installed

5. Depleted gas supply

6. ODS/pilot is clogged

7. Gas regulator setting is not correct

REMEDY

1. Replace ignitor

2. Replace ignitor

3. Reconnect ignitor cable

4. Free ignitor cable if pinched by any

metal or tubing. Keep ignitor cable dry

5. Tighten nut holding piezo ignitor to

heater cabinet. Nut is located inside

heater cabinet at top

6. Replace ignitor cable

7. Replace piezo ignitor

1. Turn on gas supply or open manual

shutoff valve

2. Turn control knob to PILOT position

3. Press in control knob while in PILOT

position

4. Continue holding down control knob.

Repeat igniting operation until air is

removed

5. Contactlocal propane/LPgas company

6. Clean ODS/pilot (see Cleaning and

Maintenance,page11)or replace ODS/

pilot assembly

7. Replace gas regulator

OBSERVED PROBLEM

When ignitor button is pressed and control

knob is pressed in and turned to the PILOT

position, there is no spark at ODS/pilot

When ignitor button is pressed and control

knob is pressed in and turned to the PILOT

position, there is spark at ODS/pilot but no

ignition

101850

OWNER’S MANUAL

OBSERVED PROBLEM

ODS/pilot lights but flame goes out when

control knob is released

POSSIBLE CAUSE

1. Control knob not fully pressed in

2. Control knob not pressed in long

enough

3. Manual shutoff valve not fully open

4. Thermocouple connection loose at con-

trol valve

5. Pilotflame not touching thermocouple,

which allows thermocouple to cool,

causingpilotflametogoout.This prob-

lem could be caused by one or both of

the following:

A) Low gas pressure

B) Dirty or partially clogged ODS/

pilot

6. Thermocouple damaged

7. Control valve damaged

TROUBLESHOOTING

Continued

REMEDY

1. Press in control knob fully

2. After ODS/pilot lights, keep control

knob pressed in 10 seconds

3. Fully open manual shut-off valve

4. Hand tighten until snug, then tighten

1/4 turn more

5. A) Contact local propane/LPgas com-

pany

B) Clean ODS/pilot (see Cleaning and

Maintenance,page11)or replace ODS/

pilot assembly

6. Replace thermocouple

7. Replace control valve

Burner(s) does not light after ODS/pilot is

lit

Delayed ignition of burner(s)

Burner backfiring during combustion

Burner plaque(s) does not glow

Slight smoke or odor during initial opera-

tion

Heater produces a clicking/ticking noise

just after burner is lit or shut off

1. Clean burner orifice(s) (see Cleaning

and Maintenance, page 11) or replace

burner orifice(s)

2. Replace burner orifice(s)

3. Contactlocal propane/LPgas company

1. Contactlocal propane/LPgas company

2. Clean burner orifice(s) (see Cleaning

and Maintenance, page 11) or replace

burner orifice(s)

1. Clean burner orifice(s) (see Cleaning

and Maintenance, page 11) or replace

burner orifice(s)

2. Contactlocal propane/LPgas company

3. Replace burner

4. Replace gas regulator

1. Replace burner

2. Contactlocal propane/LPgas company

3. Turn control knob until it locks at de-

sired setting

1. Problem will stop after a few hours of

operation

1. This is common with most heaters. If

noise is excessive, contact qualified

service person

1. Burner orifice(s) is clogged

2. Burner orifice(s) diameter is too small

3. Inlet gas pressure is too low

1. Manifold pressure is too low

2. Burner orifice(s) is clogged

1. Burner orifice(s) is clogged or damaged

2. Inlet gas pressure is too low

3. Burner damaged

4. Gas regulator defective

1. Plaque damaged

2. Inlet gas pressure is too low

3. Control knob set between locked posi-

tions

1. Residues from manufacturing pro-

cesses

1. Metal expanding while heating or con-

tracting while cooling

101850

PROPANE/LP GAS HEATERS

VANGUARD VP5C AND VP10

Gas odor even when control knob is in OFF

position

Gas odor during combustion

Moisture/condensationnoticedonwindows

1. Locate and correct all leaks (seeCheck-

ing Gas Connections, page 9)

2. Replace control valve

1. Take apart gas tubing and remove for-

eign matter

2. Locate and correct all leaks (seeCheck-

ing Gas Connections, page 9)

1. Refer to Air for Combustion and Venti-

lation requirements (page 3)

1. Gas leak. See Warning statement at

top of page

2. Control valve defective

1. Foreign matter between control valve

and burner

2. Gas leak. See Warning statement at

top of page

1. Not enough combustion/ventilation air

POSSIBLE CAUSE

1. Heater burning vapors from paint, hair

spray, glues, etc. (See

IMPORTANT

statement above)

2. Low fuel supply

3. Gas leak. See Warning statement

above

1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

REMEDY

1. Ventilate room. Stop using odor-caus-

ing products while heater is running

2. Refill supply tank

3. Locate and correct all leaks (seeCheck-

ing Gas Connections, page 9)

1. Open window and/or door for ventila-

tion

2. Contactlocal propane/LPgas company

3. Clean ODS/pilot (see Cleaning and

Maintenance, page 11)

OBSERVED PROBLEM

Heater produces unwanted odors

Heater shuts off in use (ODS operates)

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediatelycallyourgassupplierfromaneighbor’sphone.Followthe

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

IMPORTANT:

Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke,

cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors.

101850

OWNER’S MANUAL

VP10 VP5C

Btu (Variable) 5,500/10,000 5,500

Type Gas Propane/LP Only Propane/LP Only

Ignition Piezo Piezo

Pressure Regulator Setting 8" W.C. 8" W.C.

Inlet Gas Pressure (inches of water)

Maximum 14" 14"

Minimum 11" 11''

Dimensions, Inches (H x W x D)

Heater 20 1/2 x 13 1/2 x 5 20 1/2 x 13 1/2 x 5

Carton 25 x 16 11/16 x 7 1/2 25 x 16 11/16 x 7 1/2

Weight (pounds)

Heater 14 13

Shipping 18 17

You may have further questions about in-

stallation, operation, or troubleshooting.

Ifso,contactDESAInternational’sTechni-

calServiceDepartment at 1-800-323-5190.

TECHNICAL

SERVICE

SPECIFICATIONS

When gas pressure is too low

• pilot will not stay lit

• burner(s) will have delayed ignition

• heater will not produce specified heat

• propane/LP gas supply may be low

When gas quality is bad

• pilot will not stay lit

•burner(s)willproduceflamesandsoot

• heater will backfire when lit

Youmayfeelyourgaspressureistoolowor

gas quality is bad. If so, contact your local

propane/LP gas supplier.

SERVICE HINTS

REPLACEMENT

PARTS

Note:

Use only original replacement parts.

Thiswillprotectyourwarrantycoveragefor

parts replaced under warranty.

ACCESSORY

Purchase this heater accessory from your

local dealer. If they cannot supply this ac-

cessory, call DESA International’s Parts

Department at 1-800-972-7879 for infor-

mation. You can also write to the address

listed on the back page of this manual.

MANUAL SHUTOFF VALVE -

GA5010

Manual shutoff valve with 1/8" NPT tap.

SERVICE

PUBLICATIONS

Youcanpurchaseaservicemanualfromthe

address listed on the back page of this

manual. Send a check for $5.00 payable to

DESA International.

Parts Under Warranty

Contact authorized dealer from whom you

purchasedthisproduct.Iftheyareunableto

supply original replacement part(s), call

DESAInternational’sTechnicalServiceDe-

partment at 1-800-323-5190 for referral in-

formation.

When contacting your dealer or DESA In-

ternational, have ready:

• your name

• your address

• model number of your heater

• how heater was malfunctioning

• type of gas used (propane/LPor natu-

ral gas)

• purchase date

Usually,wewillaskyoutoreturnthe defec-

tive part to the factory.

Parts Not Under Warranty

Contact authorized dealers of this product.

If they cannot supply original replacement

part(s), call DESA International’s Parts

Department at 1-800-972-7879 for referral

information.

When calling DESA International, have

ready:

• model number of your heater

• the replacement part number

101850

PROPANE/LP GAS HEATERS

VANGUARD VP5C AND VP10

PARTS LIST

Model VP5C

This list contains replaceable parts used in your heater. When ordering parts, follow the instructions

listed under Replacement Parts on page 15 of this manual.

HEATER EXPLODED VIEW

PARTS AVAILABLE - NOT SHOWN

KEY PART

NO. NUMBER DESCRIPTION QTY.

14 099057-01 Pressure Tap Fitting 1

15 098276-01 1/8 Pipe Plug 1

16 099468-10 Cabinet Assembly 1

17 099415-02 Gas Regulator 1

18 098303-02 Screw, #6 x 5/16" 2

19 098508-01 Valve Retainer Nut 1

20 099393-02 Control Knob 1

21 M11084-26 Screw, #10 x 3/8" 2

22 099818-01 Internal Tooth Washer 1

23 102445-01 Piezo Ignitor 1

24 098271-03 Ignitor Cable 1

099395-08 Control Position Label 1

100642-02 Assembly, Hardware 1

KEY PART

NO. NUMBER DESCRIPTION QTY.

1 098304-01 Screw, #10 x 3/8" 2

2 099467-03 Front Panel Assembly 1

3 099318-03 Grill Guard 1

4 101108-01 Grill Guard Clip 2

5 099469-01 Reflector Assembly 1

6 M15823-37 Screw Hex #8 x 1/4" 9

7 099059-03 ODS/Pilot Assembly 1

7-1 098514-01 Thermocouple 1

7-2 098594-01 Ignitor Electrode 1

8 099884-01 Burner Assembly 1

9 099056-01 Injector 1

10 099390-01 Tubing - Valve to burner 1

11 099387-05 Pilot Tubing - Valve to pilot 1

12 099391-02 Tubing - Regulator to valve 1

13 100829-01 Control Valve 1

7-1

7-2

ODS/PILOT GRHpv013.V

GRHVP5B

101850

OWNER’S MANUAL

PARTS LIST

Model VP10

This list contains replaceable parts used in your heater. When ordering parts, follow the instructions

listed under Replacement Parts on page 15 of this manual.

HEATER EXPLODED VIEW

PARTS AVAILABLE - NOT SHOWN

KEY PART

NO. NUMBER DESCRIPTION QTY.

15 099057-01 Pressure Tap Fitting 1

16 098276-01 1/8 Pipe Plug 1

17 099468-08 Cabinet Assembly 1

18 099415-02 Gas Regulator 1

19 098303-02 Screw, #6 x 5/16" 2

20 098508-01 Valve Retainer Nut 1

21 099393-02 Control Knob 1

22 M11084-26 Screw, #10 x 3/8" 2

23 099818-01 Internal Tooth Washer 1

24 102445-01 Piezo Ignitor 1

25 098271-03 Ignitor Cable 1

099395-07 Control Position Label 1

100642-02 Assembly, Hardware 1

KEY PART

NO. NUMBER DESCRIPTION QTY.

1 098304-01 Screw, #10 x 3/8" 2

2 099467-03 Front Panel Assembly 1

3 099318-03 Grill Guard 1

4 101108-01 Grill Guard Clip 2

5 099469-02 Reflector Assembly 1

6 M15823-37 Screw Hex #8 x 1/4" 10

7 099059-03 ODS/Pilot Assembly 1

7-1 098514-01 Thermocouple 1

7-2 098594-01 Ignitor Electrode 1

8 099884-02 Burner Assembly 1

9 099056-01 Injector 2

10 099390-02 Tubing - Valve to plaque A 1

11 099387-05 Pilot Tubing - Valve to pilot 1

12 099392-01 Tubing - Valve to plaque B 1

13 099391-02 Tubing - Regulator to valve 1

14 100432-01 Control Valve 1

7-1

7-2

ODS/PILOT

GRH VP11AGRH VP11A

GRH VP11AGRH VP11A GRHpv013.U

101850

PROPANE/LP GAS HEATERS

VANGUARD VP5C AND VP10

NOTES

_______________________________________________________________________________________________

101850

OWNER’S MANUAL

NOTES

_______________________________________________________________________________________________

WARRANTY INFORMATION

Always specify model and serial numbers when communicating with the factory.

We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written

warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

VANGUARD VENT-FREE RESIDENTIAL GAS HEATERS

DESA International warrants this product to be free from defects in materials and components for three (3) years from the date of

first purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable

instructions. To make a claim under this warranty the Bill of Sale or cancelled check must be presented.

Thiswarranty isextendedonlyto theoriginalretailpurchaser. Thiswarrantycovers the costofpart(s) requiredtorestorethisheater

to proper operating condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s)

MUST be obtained through authorized dealers of this product and/or DESA International who will provide original factory

replacementparts.Failuretouseoriginalfactoryreplacementpartsvoidsthiswarranty.TheheaterMUSTbeinstalledbyaqualified

installer in accordance with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become

damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic

cost, labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the

owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE

PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND

LIMITSTHE DURATION OF ANY AND ALL IMPLIEDWARRANTIES, INCLUDING WARRANTIES OF MERCHANTA-

BILITY AND FITNESS FOR A PARTICULAR PURPOSE TO THREE (3) YEARS ON ALL COMPONENTS FROM THE

DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE

PRICE OF THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES

WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or

consequentialdamages,so the above limitation on implied warranties, orexclusion or limitation on damages may not applytoyou.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

For information about this warranty write:

101850-01

REV. D

7/97

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

KEEP THIS WARRANTY

Model

Serial No.

Date Purchased

This manual suits for next models

Table of contents

Other Vanguard Gas Heater manuals

Vanguard

Vanguard VMH3000TNA Quick start guide

Vanguard

Vanguard BLUE FLAME VP2000BTC Quick start guide

Vanguard

Vanguard MINI-HEARTH VMH2800TPC Operation manual

Vanguard

Vanguard GVB50P Quick start guide

Vanguard

Vanguard UNVENTED (VENT-FREE) PROPANE/LP GAS LOG... Specification sheet

Vanguard

Vanguard VN6D Quick start guide

Vanguard

Vanguard PRVYS18PWA Quick start guide

Vanguard

Vanguard VP11A Quick start guide

Vanguard

Vanguard VN18 Original instructions

Vanguard

Vanguard FLAME-MAX User manual

Vanguard

Vanguard VP1600ITB Quick start guide

Vanguard

Vanguard VP2000BTD Quick start guide

Vanguard

Vanguard VN12A Quick start guide

Vanguard

Vanguard Gas Log Heater Quick start guide

Vanguard

Vanguard VN1800D Quick start guide

Vanguard

Vanguard VGN30 Quick start guide

Vanguard

Vanguard VN18TA Original instructions

Vanguard

Vanguard VN1000B Quick start guide

Vanguard

Vanguard Flame-Max Vintage Oak Log Design Quick start guide

Vanguard

Vanguard VN1000BT Quick start guide

Vanguard

Vanguard VP1600TB Quick start guide

Vanguard

Vanguard Flame-Max VYS18PWA Specification sheet

Vanguard

Vanguard FLAME-MAX VYM27PR Quick start guide

Vanguard

Vanguard VGP30B Quick start guide

Popular Gas Heater manuals by other brands

Sealey

Sealey LP35.V5 instructions

Truma

Truma S 55 T EL operating instructions

Schwank

Schwank compactSchwank P40-R Installation & owner's manual

Bryant

Bryant 582A Series Installation, Start-Up and Service Instructions

Desa

Desa NZ100 Safety information and installation manual

Bromic Heating

Bromic Heating STRATOS BRAHMA 3.0 NG Installation, instruction and service manual

Flavel

Flavel Jazz Installation and maintenance instructions

HeatStar

HeatStar HSVFRD20LPBTS Operating instructions and owner's manual

Clarke

Clarke MGH2 User instructions

Mi-T-M

Mi-T-M MH-0100CM1N Operator's manual

Heatilator

Heatilator Fi36S Installation & operating instructions

ECS

ECS VFSUR18-1 Installation instructions and owner's manual

Desa

Desa GN30A Safety information and installation manual

Empire

Empire VFSUR18-2 Installation instructions and owner's manual

Design Dynamics

Design Dynamics VF-18N-BTB OWNER'S OPERATION AND INSTALLATION MANUAL

Williams

Williams 2001621 Brochure & specs

Clarke

Clarke GRH35 Operating & maintenance instructions

Medallion

Medallion MR10PT OWNER'S OPERATION AND INSTALLATION MANUAL

Vanguard VP5C Quick start guide

Popular Gas Heater manuals by other brands