Vantron VT-SBC-I350 User manual

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual www.vantrontech.com
VT-SBC-I350 Single Board Computer
User Manual
Version: 1.2
© Vantron Technology, Inc. All rights reserved.

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT- SBC-I350 | User Manual www.vantrontech.com
Revision History
No. Version Description Date
1 V1.0 First release Mar. 26, 2021
2 V1.1 Updated pinout description of J19 & J16 Jan. 10, 2022
3 V1.2 Updated procedures on image flashing Jun. 3, 2023

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT- SBC-I350 | User Manual www.vantrontech.com
Table of Contents
Foreword ...............................................................................................................................................................1
CHAPTER 1 INTRODUCTION..............................................................................................................................5
1.1 Product Overview..............................................................................................................................6
1.2 Terminology ........................................................................................................................................6
1.3 Block Diagram ....................................................................................................................................7
1.4 Specifications......................................................................................................................................8
1.5 Operating system...............................................................................................................................9
1.6 Mechanical Dimensions...................................................................................................................9
1.7 Power Supply and Consumption....................................................................................................9
1.8 Environmental Specifications .........................................................................................................9
CHAPTER 2 CONNECTOR DESCRIPTION ...................................................................................................... 10
2.1 Product Layout................................................................................................................................ 11
2.2 Memory and Storage..................................................................................................................... 11
2.2.1 LPDDR4 RAM ................................................................................................................................... 11
2.2.2 eMMC Flash..................................................................................................................................... 11
2.2.3 Storage expansion.......................................................................................................................... 11
2.2.4 EEPROM............................................................................................................................................ 12
2.3 Identification of Pin 1 .................................................................................................................... 12
2.4 Connectors and Jumpers .............................................................................................................. 12
2.4.1 J1 Power jack (1)............................................................................................................................. 12
2.4.2 J3 Battery connector (2)................................................................................................................ 13
2.4.3 U60 USB 2.0 Type-C (3) ................................................................................................................. 13
2.4.4 U14 USB 2.0 Type-A (4)................................................................................................................. 13
2.4.5 J30 USB 2.0 connector (5) ............................................................................................................ 14
2.4.6 J19 Ethernet jack (6)...................................................................................................................... 14
2.4.7 J12 3.5mm audio jack (7).............................................................................................................. 14
2.4.8 J18 HDMI (8).................................................................................................................................... 15
2.4.9 J7 MIPI DSI (9) ................................................................................................................................. 15
2.4.10 J9/J10 MIPI CSI (9).......................................................................................................................... 16
2.4.11 J4 Wi-Fi & Bluetooth antenna connector (11)......................................................................... 18
2.4.12 J5 GPS antenna connector (12)................................................................................................... 18
2.4.13 J8 Touch panel connector (13) .................................................................................................... 19
2.4.14 J11 A-Mic (14).................................................................................................................................. 19
2.4.15 U512/U513 D-Mic (15).................................................................................................................. 19
2.4.16 J13/J14 Speaker connectors (16) ................................................................................................ 20
2.4.17 J16 Button connector (17)............................................................................................................ 20
2.4.18 J15 40-pin header (18) .................................................................................................................. 21
2.4.19 J3 Micro SD slot (19)...................................................................................................................... 22
2.4.20 Buttons (20) ..................................................................................................................................... 22
CHAPTER 3 ANDROID SYSTEM MANUAL .................................................................................................... 23
3.1 Enable Developer Options............................................................................................................ 24
3.2 ADB Setup ........................................................................................................................................ 24
3.3 App Installation via ADB Commands ......................................................................................... 26
3.3.1 Prerequisites.................................................................................................................................... 26

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT- SBC-I350 | User Manual www.vantrontech.com
3.3.2 App installation............................................................................................................................... 26
3.4 Image Flashing on a Windows Host ........................................................................................... 27
3.4.1 Prerequisites.................................................................................................................................... 27
3.4.2 Driver installation ........................................................................................................................... 27
3.4.3 Image flashing ................................................................................................................................. 29
3.5 Using the Serial Ports .................................................................................................................... 31
CHAPTER 4 DISPOSAL AND WARRANTY...................................................................................................... 33
4.1 Disposal............................................................................................................................................. 34
4.2 Warranty........................................................................................................................................... 35

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 1 www.vantrontech.com
Foreword
Thank you for purchasing VT-SBC-I350 single board computer (“the Board” or “the Product”).
This manual intends to provide guidance and assistance necessary on setting up, operating or
maintaining the Product. Please read this manual and make sure you understand the
functionality of the Product before putting it into use.
Intended Users
This manual is intended for:
•Embedded software developer
•Custom development software engineer
•Other technically qualified personnel
Copyright
Vantron Technology, Inc. (“Vantron”) reserves all rights of this manual, including the right to
change the content, form, product features, and specifications contained herein at any time
without prior notice. An up-to-date version of this manual is available at www.vantrontech.com.
The trademarks in this manual, registered or not, are properties of their respective owners.
Under no circumstances shall any part of this user manual be copied, reproduced, translated,
or sold. This manual is not intended to be altered or used for other purposes unless otherwise
permitted in writing by Vantron. Vantron reserves the right of all publicly released copies of
this manual.
Disclaimer
While all information contained herein has been carefully checked to assure its accuracy in
technical details and typography, Vantron does not assume any responsibility resulting from
any error or features of this manual, nor from improper uses of this manual or the software.
It is our practice to change part numbers when published ratings or features are changed, or
when significant construction changes are made. However, some specifications of the Product
may be changed without notice.

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 2 www.vantrontech.com
Technical Support and Assistance
Should you have any question about the Product that is not covered in this manual, contact
your sales representative for solution. Please include the following information in your
question:
•Product name and PO number;
•Complete description of the problem;
•Error message you received, if any.
Vantron Technology, Inc.
Address: 48434 Milmont Drive, Fremont, CA 94538
Tel: [phone]
Email: [e-mail]
Symbology
This manual uses the following signs to prompt users to pay special attention to relevant
information.
Caution for latent damage to system or harm to personnel
Attention to important information or regulations

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 3 www.vantrontech.com
General Safety Instructions
The Product is supposed be installed by knowledgeable, skilled persons familiar with local
and/or international electrical codes and regulations. For your safety and prevention of
damage to the Product, please read and observe carefully the following safety instructions
prior to installation and operation. Keep this manual well for future reference.
•Do not disassemble or otherwise modify the Product. Such action may cause heat
generation, ignition, electronic shock, or other damages including human injury, and may
void your warranty.
•Keep the Product away from heat source, such as heater, heat dissipater, or engine casing.
•Do not insert foreign materials into any opening of the Product as it may cause the Product
to malfunction or burn out.
•To ensure proper functioning and prevent overheating of the Product, do not cover or
block the ventilation holes of the Product.
•Follow the installation instructions with the installation tools provided or recommended.
•The use or placement of the operation tools shall comply with the code of practice of such
tools to avoid short circuit of the Product.
•Cut off the power before inspection of the Product to avoid human injury or product
damage.

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 4 www.vantrontech.com
Precautions for Power Cables and Accessories
Use proper power source only. Make sure the supply voltage falls within the specified
range.
Place the cables properly at places without extrusion hazards.
There is a coin cell battery for powering the RTC. Therefore, please avoid short circuit of
the battery during transportation or operation at high temperatures.
Cleaning instructions:
•Power off before cleaning the Product
•Do not use spray detergent
•Clean with a damp cloth
•Do not try to clean exposed electronic components unless with a dust collector
Power off and contact Vantron technical support engineer in case of the following faults:
•The Product is damaged
•The temperature is excessively high
•Fault is still not solved after troubleshooting according to this manual
Do not use in combustible and explosive environment:
•Keep away from combustible and explosive environment
•Keep away from all energized circuits
•Unauthorized removal of the enclosure from the device is not allowed
•Do not change components unless the power cable is unplugged
•In some cases, the device may still have residual voltage even if the power cable is
unplugged. Therefore, it is a must to remove and fully discharge the device before
replacement of the components.

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 5 www.vantrontech.com
CHAPTER 1 INTRODUCTION

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 6 www.vantrontech.com
1.1 Product Overview
VT-SBC-I350 Single Board Computer features a thinner and smaller form factor that is easy
to integrate. It is powered by MTK® MT8365 (I350) processor, which integrates a fast 2GHz
quad-core ARM Cortex-53 CPU and a high-performance ARM Mali-G52 GPU to deliver
powerful Edge AI processing with extremely low power consumption. The board supports
up to 13MP high-definition camera, which, combined with the high-definition video
encoding and decoding technology, provides outstanding visual experience. Better yet, it
provides rich on-board interfaces and customer expansion options to meet different
application scenarios including smart retail, self-service terminals, industrial automation,
intelligent medical health, and digital media.
Featuring high flexibility and high performance, the board could work under extreme
environments with extended temperatures ranging from -20℃to +60℃, making it a
reliable industrial IoT solution.
1.2 Terminology
Terminology Description
NC No connection
VCC
Voltage common collector
GND
Ground
/
Active low signal
+
Positive of difference signal
-
Negative of difference signal
I
Input
O
Output
I/O
Input/output
P
Power or ground
A
Analog
OD
Open drain
CMOS
3.3 V CMOS
LVCMOS
Low Voltage CMOS
LVTTL
Low Voltage TTL
3.3V
3.3 V signal level
5V
5V signal level
USB
5V tolerant signal
PCIe
PCI Express signal, not 3.3 V tolerant
MMC
Multimedia Card

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 7 www.vantrontech.com
1.3 Block Diagram
MTK: MT8365
ARM Cortex-A53
Qaud_Core Low Power
Processor
2.0GHz
Mali-G52 GPU core
600MHz
14nm
Hardware Watchdog
Audio Codec
MT6390
PMIC
RTC
eMMC5.1,
16GB
EMMC V5 .1
2Kbit EEPROM
DDR-CH
I2C0
: IC Chip
: Connector
Display Connector 1x31x0.3mm
4Lane MIPI /LVDS signal
USB 2.0
Power Button
Reset
Temperature:-20~+60℃
OS: Android 10
Vol+ Button
Vol- Button
USB2.0
Type-A
1x4x1.25mm
SMT Connector
UART0 For Debug
2GB LPDDR4-3200
DDR 2x16bit
For debug CPU
WIFI/BT/GPS/FM RF
Chip
MT6631N
802.11 a/b/g/n/ac
BT5.0
GPS/Gloness/BD
WIFI Data
WIFI/BT/GPS ANT
Optional up to 4GB
4-bit MSDC1
Micro SD Socket
MIPI support up to 1920x1080
LVDS support up to 1080x720
Modle:FPC031003-31LG
1x6x0.5mm
TP
connector
I2C1,Reset,
Interrupt
signal,3.3V
For C TP
2x4x1.0mm
SMT Connector
JTAG For Debug
2x20x2.0mm
THR Connector
UART1 For Debug DSP or GE UART
UART2 For GE UART
I2C2
SPI
MSDC2 For SDIO or 6xGPIOs
USB 2.0
USB 2.0
VSYS
3.3V
DC IN
BT Data
GPS Data
Control signal
LNA
GPS signal
FILTER
5G
2.4G
1.6G
Back lig ht
power
Front Camera
1x31x0.3mm
Rear Camera
1x31x0.3mm
MIPI CSI0
I2C3
MIPI CSI1
DPI to HMDI
IT66121FN
Ethernet PHY
RTL8201F
DPI
RMII
MUX sign al
HDMI Type-A
RJ45
D-MIC
D-MIC
DMIC0
DMIC1
I2S
Power_SPI
1x2x1.25mm
A-MIC
Audio Jack 3.5mm
4-sections
26M_CLK OUT
Watchdog
Reset signal
CON
AMP
CON
AMP
VPROC
VCROE
VSRAM_PROC
VS1
LDO
26M
Support
2x1W/8R
speaker
Charger
RT9466
VSYS VSYS
Battery Con
Gauge
Power Con
12V
Micro USB
USB 2.0 OTG
G-sens or
MMA8452
AW8737SCSR
I2C2
V_BAT
MSDC0
I2C0

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 8 www.vantrontech.com
1.4 Specifications
VT-SBC-I350
System
CPU
MTK MT8365 (I350), Quad-core ARM Cortex-A53, 2.0GHz (Max)
GPU
Mali-G52, 3D graphic accelerator, capable of processing 57.6 GFLOPS
and 1600M pixel/s, 600MHz
Memory
2GB LPDDR4-3200, up to 4GB
Storage
16GB eMMC 5.1, up to 64GB
2Kb EEPROM
1 x Micro SD slot (SDIO 3.0)
PMIC
MT6390
Communication
Ethernet
1 x RJ45, 10M/100Mbps, RTL8201 (Ethernet PHY)
Wi-Fi & BT Wi-Fi 802.11 a/b/g/n/ac + BT 5.0
GNSS
GPS + Glonass + Beidou/Galileo
Media
Display
1 x 4-Lane MIPI DSI, up to 1920 x 1080
1 x HDMI (Type-A), up to 1920 x 1080
Camera
2 x 4-Lane MIPI CSI, 13 MP, 1080P/60fps video decoder
Audio
1 x A-Mic to PMIC
2 x D-Mic to AP (CPU), noise reduction
1 x 3.5mm combo audio jack
2 x 1.2W Speaker connector
I/Os
Serial
2 x UART for communication
1 x UART for debugging
USB
1 x USB 2.0 Type-C (OTG supported)
1 x USB 2.0 Type-A
1 x USB 2.0 connector (not for use simultaneously with USB Type-A)
GPIO
4 x GPIO
RTC
Supported, powered by an external battery
Watchdog
Supported
Expansion I2C 1 x I2C for TP 1 x I2C for external communication
System Control Button
1 x ON/OFF button
1 x Reset button
2 x Volume button (+ & -)
1 x Button connector
Sensor
G-sensor
3-Axis G-sensor
Power Input 12V DC 1 x Power jack
Software
Operating system
Android 10
Device management
platform
BlueSphere MDM
OTA tool BlueSphere OTA
Mechanical Dimensions 100mm x 75mm
Cooling mode
Fanless
Environment
Condition
Temperature
Operating: -20℃~+60℃
Storage: -40℃~+85℃
Humidity
RH 5%-95%
Certification
FCC (part 15 class B)
ESD (contact: ±4KV and air: ±8KV)

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 9 www.vantrontech.com
1.5 Operating system
VT-SBC-I350 supports Android 10 operating systems.
1.6 Mechanical Dimensions
•100mm x 75mm
1.7 Power Supply and Consumption
VT-SBC-I350 works at 12V DC power input. It is recommended to use a 12V/2A power
adapter for the power supply.
The power consumption of the Board is 5W at the maximum. It should be pointed out that
power consumption is largely determined by the RAM, storage capacity, and other
configurations of the board.
1.8 Environmental Specifications
VT-SBC-I350 works at a temperature ranging from -20℃to +60℃and is designed to be
stored at a temperature ranging from -40°C to +85°C and at relative humidity of RH 5% to
96% for non-condensing purpose.

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 10 www.vantrontech.com
CHAPTER 2 CONNECTOR DESCRIPTION

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 11 www.vantrontech.com
2.1 Product Layout
The board I/Os will be described in detail in 2.4 Connectors and Jumpers following the
sequencing numbers provided here.
2.2 Memory and Storage
2.2.1 LPDDR4 RAM
VT-SBC-I350 is equipped with a 2GB LPDDR4 RAM (frequency: 3200MHz) by default, and users
also have the option of 4GB RAM.
2.2.2 eMMC Flash
VT-SBC-I350 provides an eMMC 5.1 flash up to 64GB using SDIO interface, and the default
capacity is 16GB. It is used as the default boot and storage device.
2.2.3 Storage expansion
VT-SBC-I350 provides a Micro SD slot for storage expansion.
(10) MIPI CSI
(15) D-Mic
(18) Debug,
UART, GPIO, I
2
C
(15) D-Mic
(19) Micro SD
slot
(17) Button
(16) SPK_L
(16) SPK_R
(14) A-Mic
(2) Battery
(1) DC
(3) USB
Type-C
(7)
Audio
(6)
Ethernet
(8)
HDMI
(4) USB
Type-A
(13) TP
(5) USB 2.0
(12) GPS ant.
(11) Wi-Fi ant.
(9)MIPI DSI
(10) MIPI CSI

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 12 www.vantrontech.com
2.2.4 EEPROM
The Board implements a 2Kb EEPROM (address 0x50), communicating with the CPU using
I2C0. The EEPROM is for storing hardware version, firmware information, and other
custom information. The write protection is controlled by software.
2.3 Identification of Pin 1
Unless otherwise stated, pin 1 of a connector is seated on a square pad that is different
from the round pads used for other pins. Sometimes, pin 1 is next to a trigonal mark on
the board. When there are two rows of pins on a connector, the row with pin 1 is
composed of odd numbers and the other is composed of even numbers.
Usually, there will be numbers or marks next to the pins of a connector on the board to
indicate the pinouts.
2.4 Connectors and Jumpers
This section is going to brief the connectors/jumpers on the Board with corresponsive
pinout description.
2.4.1 J1 Power jack (1)
VT-SBC-I350 works at 12V DC power input (12V/2A power adapter recommended)
supplied through the power jack on the board.

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 13 www.vantrontech.com
2.4.2 J3 Battery connector (2)
VT-SBC-I350 offers a battery connector for connecting an external battery or rechargeable
power source. This is useful in situations where there might be a power outage or failure
in the main power supply. It ensures key processes or functions not to be interrupted.
Pinout description:
No. Signal Type Level Description
1
VCC_BAT
P
3.8V
Battery anode
2
VCC_BAT
P
3.8V
Battery anode
3
VCC_BAT
P
3.8V
Battery anode
4
BAT_GND
P
Battery cathode
5
BAT_GND
P
Battery cathode
6
BAT_GND
P
Battery cathode
7
BATT_TS
AI
Battery temp. input
Note: Only when an external battery is connected, can the RTC feature be enabled.
2.4.3 U60 USB 2.0 Type-C (3)
VT-SBC-I350 has a USB 2.0 Type-C interface, supporting USB OTG feature for data
transmission, board debugging, peripheral connection, etc. The maximum output of this
interface is 5V/1A.
2.4.4 U14 USB 2.0 Type-A (4)
VT-SBC-I350 has a USB 2.0 Type-A interface, supporting data transmission, peripheral
connection, etc. The maximum output of this interface is 5V/1A.
Pin
1

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 14 www.vantrontech.com
2.4.5 J30 USB 2.0 connector (5)
The USB 2.0 connector cannot be used simultaneously with the USB 2.0 Type-A interface,
You can choose one for peripheral connection.
Pinout description:
No. Signal Type Level Description
1
VBUS1
P
5V output, Max. 1A
2
USB_DM
D-
3
USB_DP
D+
4
GND
P
GND
Ground
2.4.6 J19 Ethernet jack (6)
VT-SBC-I350 offers an RJ45 Ethernet jack, supporting 10/100Mbps transmission rate. The
Ethernet jack has two LED indicators, green for activity indication and yellow for link
indication.
2.4.7 J12 3.5mm audio jack (7)
The on-board 3.5mm combo audio jack is for connecting a headphone or an external
speaker/microphone for audio output or input, such as audio recording, voice call, etc.
Pin 1

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 15 www.vantrontech.com
2.4.8 J18 HDMI (8)
The Board has an HDMI 1.4 interface for image output, supporting a resolution up to 1920
x 1080.
2.4.9 J7 MIPI DSI (9)
VT-SBC-I350 offers a 4-lane MIPI DSI connector (1 x 31, 0.3mm) for connecting an external
display, supporting a resolution up to 1920 x 1080.
Pinout description:
No. Signal Type Level Description
1
VCC_LED0_A_MIPI
P
LED anode
2
VCC_LED0_A_MIPI
P
LED anode
3
VCC_LED0_A_MIPI
P
LED anode
4
NC
5
VCC_LED0_K_MIPI
P
LED cathode
6
VCC_LED0_K_MIPI
P
LED cathode
7
VCC_LED0_K_MIPI
P
LED cathode
8
VCC_LED0_K_MIPI
P
LED cathode
9
GND
P
GND
Ground
10
GND
P
GND
Ground
11
MIPI_DSI_D2P
O
MIPI DSI data 2 +
12
MIPI_DSI_D2N
O
MIPI DSI data 2 -
13
GND
P
GND
Ground
14
MIPI_DSI_D1P
O
MIPI DSI data 1 +
15
MIPI_DSID1N
O
MIPI DSI data 1 -
16
GND
P
GND
Ground
17
MIPI_DSI_CLKP
O
MIPI CSI clock +
18
MIPI_DSI_CLKN
I/O
MIPI CSI clock -
P
in 1
P
in 31

Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-SBC-I350 | User Manual 16 www.vantrontech.com
19
GND
P
GND
Ground
20
MIPI_DSI_D0P
O
MIPI DSI data 0 +
21
MIPI_DSI_D0N
O
MIPI DSI data 0 -
22
GND
P
GND
Ground
23
MIPI_DSI_D3P
O
MIPI DSI data 3 +
24
MIPI_DSI_D3N
O
MIPI DSI data 3 -
25
GND
P
GND
Ground
26
NC
27
LCD_RESET
O
1.8V
MIPI LCD reset output
28
NC
29
VCC1V8_LCD
P
1.8V
1.8V power output
30
VCC3V3_LCD
P
3.3V
3.3V power output
31
VCC3V3_LCD
P
3.3V
3.3V power output
2.4.10 J9/J10 MIPI CSI (9)
VT-SBC-I350 offers two 4-lane MIPI CSI connectors (1 x 31, 0.3mm) for connecting front
and rear cameras, supporting a resolution up to 13MP.
Pinout description of J9:
No.
Signal
Type
Level
Description
1
GND
P
GND
Ground
2
MIPI_CSI0_D3N
I
MIPI CSI data 3 -
3
MIPI_CSI0_D3P
I
MIPI CSI data 3 +
4
GND
P
GND
Ground
5
MIPI_CSI0_D2N
I
MIPI CSI data 2 -
6
MIPI_CSI_D2P
I
MIPI CSI data 2 +
7
GND
P
GND
Ground
8
MIPI_CSI0_D1N
I
MIPI CSI data 1 -
9
MIPI_CSI0_D1P
I
MIPI CSI data 1 +
10
GND
P
GND
Ground
11
MIPI_CSI0_D0N
I
MIPI CSI data 0 -
12
MIPI_CSI0_D0P
I
MIPI CSI data 0 +
13
GND
P
GND
Ground
P
in 1
P
in 31