Vaportek VAPORTRONIC 2.0 Series User manual

1. Position Vaportronic 2.0 on wall where unit is to be mounted &
mark top of unit. Allow at least 3” clearance above unit for
hinged cover to lift open.
2. Measure 1.25" down from mark & drill top mounting hole using
3/16" drill bit.
3. Insert supplied anchor into hole & insert supplied screw into
anchor leaving a 1/8" protrusion.
4. Using supplied Allen wrench, open unit by removing bottom
screw. Open cover & hang unit on top mounting screw.
5. Mark bottom hole using hang hole in back panel, remove unit,
& drill bottom mounting hole using 3/16" drill bit. Insert
supplied anchor into hole.
6. Hang unit on top mounting screw & align with bottom
mounting hole. Insert supplied screw into anchor & securely
tighten.
7. Insert 2 AA batteries.
1. Open protective bag containing EZ-Disk by tearing at notch.
Gently press EZ-Disk down & back into slot(s) to prevent
element interference with fan.
2. Install 1-5 EZ-Disks depending on your cubic footage needs.
Each EZ-Disk treats 2,000 ft3.
3. Ensure slide switch is turned ON & adjusted to desired setting.
Use setting 1 when maximum dry vapor output is required.
4. Close lid & reinsert bottom screw using Allen wrench.
5. Wash hands with soap & water to remove any residue
from handling EZ-Disks.
DEODORIZING ELEMENT INSTRUCTIONS
WALL-MOUNTING INSTRUCTIONS
May be used free-standing
or wall-mounted.
USE AND OPERATING
INSTRUCTIONS FOR THE
VAPORTRONIC 2.0™
Vaportronic 2.0
Refillable, Electronic
Wall Cabinet System
0 - 0FF
Setting 1 - One minute ON, 5 minutes OFF
Setting 2 - One minute ON, 10 minutes OFF
Setting 3 - One minute ON, 15 minutes OFF

For service advice, contact your dealer or Vaportek.
#50-1228 Rev. 3/19
SPECIFICATIONS
IMPORTANT
1. Vaportek products use natural essential oils. If an allergic
reaction occurs, please discontinue use immediately.
2. Do not allow EZ-Disk to contact surfaces other than the housing
as contact may damage finished surfaces.
3. Ideal dry vapor release occurs at 50-80°F (10-27°C).
4. Replace EZ-Disks after 30 days of use.
5. Keep out of reach of children.
1. Blinking green LED operation indicator; blinking red when
battery change is required. Unit will blink red a minimum of 72
hours before it stops operating.
2. Tamper resistant.
3. Approx. Dimensions: 7”H x 3”W x 3”L.
4. Weighs less than one pound.
5. Uses 2 AA batteries; batteries last for a minimum of 30 days at
the highest setting.
Vaportek warrants this unit to be free from defects in workmanship
and materials, under normal use and service, for one year from date
of purchase by the original purchaser. If, at any time during the
warranty period, the product is found to be defective or
malfunctions, Vaportek will either repair or replace the defective
part(s) at its discretion. Warranty does not apply if it is shown by
Vaportek that the defect or malfunction was caused by unauthorized
modifications, neglect, or abuse by the consumer. Further, any costs
incurred by consumer due to unauthorized changes made to the
product will not be covered by Vaportek. This warranty does not
cover any other charges incurred by the consumer. Vaportek's sole
responsibility is to repair or replace products within the terms stated
above. This warranty applies only to products sold and used in the
United States and Canada. Goods submitted for repair under this
warranty must be sent freight prepaid to Vaportek, Inc. Call first for
a return authorization number.
ONE YEAR LIMITED WARRANTY
P: 800.237.6367 | F: 262.246.5065
www.vaportek.com | [email protected]m
Proudly made in the USA