VAST DWS-1113 User manual
Apple iOS devices / Android devices
Motion JPEG
about 10M from a WiFi connector device
2.4GHz band width
Ad hoc mode
WiFi IEEE802.11b/g/n(1T1R)
Li-Polymer 3000mA
3.7V/370mA(battery),5V/900mA(DC in)
5V/200mA(WiFi Dongle)
3.5 hrs with 3000mA Li-Polymer battery
170.2g with Battery
DWS-1113 WiFi Station
Specification
Contents
Components Names and Function
Compatible Host Devices
Support UVC camera video stream format
Camera operational range
Frequency
Access format
Transmission protocol
Battery
5V/2000 mA
Adapter
Power consumption
Continuous operation time
Weight
DWS-1113 WiFi Station x1
Power adapter x1
User Guide x1
WiFi Dongle
Reset Key
Power Switch
USB MJPEG Camera INPUT
Power Bank
Micro USB (For Charge)
LAN Port (For Firmware update)
1
Pad Holder For Use
LED Indicators
Getting started
iOS app operation
WiFi Dongle
Green: Power on and working.
Power Bank
Green: Normal with sufficient charge, or charging is complete
Blinking Red: Low battery. Please plug in power adapter or WiFi Station will be off after 60 seconds.
Orange: Battery is charging.
WiFi Dongle LED
Power Bank LED
1. Download the “S-Viewer” app from Apple App Store or Android ”Google Play”.
2. Turn on the power switch. WiFi Dongle LED will stay GREEN.
3. Connect your USB Microscope or USB camera to DWS-1113 WiFi Station.
4. Connect the mobile device to the WiFi network. (Please see the section on iOS/Android app operation)
1. Go to WiFi setting and choose WiFi setup
2. Select WiFi, and turn it on.
3. Select WiFi Station “SSID”
4. Key in the password. Connection is established.
5. Go back to main menu.
6. Find and hit the S-Viewer icon to access WiFi Station’s features.
Remark:
The initial SSID can be found on the label located on the bottom of the device.
The initial password is 12345678.
2
Remark:
The initial SSID can be found on the label located on the bottom of the device.
The defult password is 12345678.
Android app operation
1. Go to WiFi setting and choose WiFi setup.
2. Select WiFi, and turn it on.
3. Select WiFi Sation “SSID”.
4. Key in the password. Connection is established.
5. Go to the Home screen to show ALL apps.
6. Find and hit the S-Viewer icon to access WiFi Station’s features.
3 4
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it
also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in
accordance with provided instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter. End-users and installers must be provide with
antenna installation instructions and consider removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
