Vax V-112AA User manual

www.vax.co.uk lease read carefully before using this cleaner.
Always fully extend the mains cable before use.
Retain for future reference.
Vax careline
0870 6061248
instruction manual
Bagless cylinder
Vax model number:
V-112AA
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:49 Page 1

V-112AA
1. Diagram
www.vax.co.uk
2 parts overview
1
56
2 3 4 7
Fig.1/2
Fig.1/1
1 Dirt container handle
2 Cord rewind button
3 Variable power dial
4 On/off button
5 Dirt container
6 Wheel
7 Carry handle
8 Telescopic tube
9 Combination floor head
10 Dusting brush
11 Crevice tool
12 Upholstery tool
13 Flexible hose
8
13
9
11
10 12
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 2

3
Vax Careline 0870 606 1248
safety information
2. Safety Information
For Household Use Only
When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:
1. Only use the vacuum cleaner indoors on dry
surfaces.
2. Turn off the vacuum cleaner controls before
connecting or disconnecting from the mains supply.
3. Always unplug the vacuum cleaner before
connecting or disconnecting the vacuum hose and
accessories.
4. Children should be supervised to ensure that they
do not play with the appliance.
5. The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
6. Use only as described in this manual.
Use only the manufacturer’s recommended
attachments.
7. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the vacuum cleaner with a
damaged cord or plug. If the supply cord or plug is
damaged, return the vacuum cleaner to a Vax
Authorised Service Agent or suitably qualified
person for examination, repair or adjustment.
8. Do not pull or carry by the cord. Do not use the cord
as a handle, close a door on the cord or pull the cord
around sharp edges or corners. Do not run the
vacuum cleaner over the cord. Keep the cord away
from heated surfaces.
9. Do not handle the plug or vacuum cleaner with wet
hands. Do not use outdoors or on wet surfaces.
10. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.
12. Do not pick up hot coals, cigarette butts, matches or
any hot, smoking or burning objects.
13. Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc) or use in the
presence of explosive liquids or vapours.
14. Do not vacuum up harmful or toxic material (chlorine
bleach, ammonia, drain cleaner, etc).
15. Do not vacuum up hard or sharp objects such as
glass, nails, screws, coins, etc.
16. Do not use without the filters in place.
17. Take extra care when vacuuming stairs.
18. Keep vacuuming area well lit.
19. Store the vacuum cleaner indoors in a cool, dry area.
20. Turn off the on/off switch before unplugging the
vacuum cleaner.
21. Use only CE-approved 13 amp extension cords.
Non-approved extension cords may overheat. Care
should be taken to arrange the cord so that the cord
cannot be pulled or tripped over.
WARNING: Always switch off and unplug the
vacuum cleaner from the electrical outlet
before assembling, opening or emptying the dirt
container, or before connecting/disconnecting the
attachments.
CAUTION: The vacuum cleaner is a very
powerful unit. Before plugging the cord into
the electrical outlet, make sure the switch is in the
‘off’ position.
IM ORTANT: If the inlet, hose or telescopic
tube is blocked, switch off the vacuum cleaner
and remove the blockage(s) before re-starting the
vacuum cleaner.
IM ORTANT: Cleaning filters improves vacuum
performance. Make sure all the filters are
completely dry before inserting back into the vacuum
cleaner.
This vacuum cleaner is intended for household use only
and not for commercial or industrial use.
!
!
!
!
Motor Thermostat
IM ORTANT: The motor is equipped with a thermal
cut-out. If for any reason, the vacuum cleaner should
over-heat, the thermostat will automatically turn the
unit off. Should this occur, unplug the vacuum cleaner
from the electrical outlet and turn off the switch.
Remove the dirt container and empty. Clean the
filters. Allow the cleaner to cool for approximately one
(1) hour. To re-start, plug into an electrical outlet and
switch back on.
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 3

www.vax.co.uk
4 assembly / operation
3. How to Assemble
IM ORTANT: Always unplug the vacuum cleaner
from the electrical outlet before assembling or
removing the accessories.
1. Insert the flexible hose into the inlet on the main body
of the vacuum cleaner. ush in until it clicks into
position (Fig.3/1).
2. ush the telescopic extension tube on to the end of
the handle (Fig.3/2).
3. The telescopic extension tube can be lengthened or
shortened by pushing the button in and sliding the
tube apart or together as required (Fig.3/3).
4. Fit the combination floor head by pushing onto the
extension tube (Fig.3/4).
4. How to Operate
Cord Release
Fully unwind the power cord. A yellow mark on the power
cord indicates the recommended cord length. Do not
exceed the cord length beyond the red mark.
On/Off Button
Insert the power plug into the electrical outlet. Ensure the
vacuum cleaner is switched off.
ress the on/off button located on the top of the vacuum
cleaner and press the button again to turn the vacuum
cleaner off.
Carpet Cleaning
For carpet and rug cleaning press the rocker switch on the
combination floor head to raise the brushes.
Hard floor cleaning
For hard floor cleaning, press the rocker switch on the
combination floor head to lower the brushes.
Cord Rewind
To rewind the power cord, press the cord rewind button,
located on the top of the vacuum cleaner, and guide the
power cord with one hand. This will prevent the cord from
whipping which could cause damage or injury.
Variable ower
Located between the cord rewind and the on/off button
there is a variable power dial. Rotate the dial clockwise to
increase the power and anti-clockwise to reduce.
Carry Handle
Use the carry handle located behind the cord rewind
button and on/off button to move the vacuum cleaner
from room to room.
Hose Storage
For convenience there is a slot located located on the rear
of the vacuum cleaner where the floor tool and hose can
be parked for carrying and storage.
Fig.3/1
Fig.3/2
Fig.3/3
Fig.3/4
!
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 4

5
Vax Careline 0870 606 1248
accessories / dirt container & filter
5. Accessories
The accessories can be attached directly to the handle by
removing the telescopic tube and pushing in the desired
accessory.
The accessories can also be attached to the telescopic
tube for extra reach. Remove the combination floor head
and push on the desired accessory.
Dusting brush: for delicate surfaces.
Upholstery tool: for carpets, upholstery, stairs, etc.
Crevice Tool: for crevices, corners and cracks, etc.
NOTE: For stair cleaning, the unit should always be
placed at the bottom of the stairs.
6. Dirt Container & Filter:
Removal and Replacement
WARNING: Always unplug the vacuum cleaner
from the electrical outlet before removing the
dirt container.
WARNING: Do NOT use the vacuum cleaner
without ALL of the filters in place.
NOTE: For best performance, replace filters annually.
Emptying the Dirt Container
ress the button located on the top of the dirt container
handle to pull out the dirt container (Fig.6/1)
osition the dirt container over a rubbish bin and press the
dirt container release catch as shown (Fig.6/2)
When all the dirt has fallen, close the dirt container bottom
and replace back in the unit until a click is heard.
Cleaning the Central Filter
Remove the dirt container as directed.
With the dirt container bottom open reach inside the dirt
container as shown for the central filter (Fig.6/3).
Fig.6/1
Fig.6/2
!
!
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 5

www.vax.co.uk
6 dirt container & filter
Rotate anti-clockwise and pull away from the dirt
container (Fig. 6/4). The dirt container may be wiped to
clean.
The central filter should then be cleaned with a soft brush
and wiped with a damp cloth (Fig.6/5).
Leave the central filter to completely dry before replacing.
IM ORTANT: The central filter should not be
submerged in water.
NOTE: Do NOT use any detergents or boiling water to
wash the filter. Vax recommends washing the filter
every time you empty the dust container.
Replace the filter back in the dirt container turning it
clockwise into lock position.
Replace the dirt container as directed.
Cleaning the re Motor Filter
Remove the dirt container as directed.
Remove the filter as shown (Fig.6/6).
Rinse the pre-motor and foam filter in warm water (max
40ºC) allow to air dry for at least 24 hours before replacing
(Fig.6/7).
Return the pre-motor filter to the dirt container and then
to the vacuum cleaner.
Cleaning the ost Motor Filter
NOTE: This is located at te rear of the vacuum cleaner.
Release the post-motor cover by pressing in the catch at
the top of the cover.
Remove the filter by pulling the filter away from the cover.
(Fig.6/8).
Fig.6/3
Fig.6/4
Fig.6/6
Fig.6/7
Fig.6/8
Fig.6/5
!
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 6

7
Vax Careline 0870 606 1248
dirt container & filter / clearing blockages
The post motor filter can be rinsed in warm water (max
40ºC). Allow to air dry for at least 24 hours before
replacing.
NOTE: Do not use any detergents or boiling water to
wash the filter. Vax reccommends washing the filter
every 4 weeks).
Replace the post motor filter in the case and re-fit to the
back of the vacuum cleaner.
7. Clearing Blockages
WARNING: To reduce the risk of electric shock,
the power cord must be disconnected before
performing maintenance or troubleshooting checks.
Turn the vacuum cleaner off and unplug from the electrical
outlet.
The flexible hose can be disconnected from the vacuum
cleaner by pushing in the button on the hose and pulling
away from the machine. Remove any blockages found then
re-connect the hose securely.
8. Storage
IM ORTANT: Always unplug the vacuum cleaner from
the electrical outlet and rewind the power cord as
directed before storing.
NOTE: Always store the vacuum cleaner base down.
!
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 7

www.vax.co.uk
8 clearing blockages / storage
9. Troubleshooting
WARNING: To reduce the risk of personal injury, unplug
the vacuum cleaner before performing maintenance or
troubleshooting checks.
ROBLEM: Vacuum cleaner won't run
Cause: Not properly plugged into electrical outlet.
Solution: lug in securely.
Cause: No electricity in the electrical outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: ush on/off switch to ‘on’.
Cause: Motor thermostat has tripped.
Solution: Switch off and unplug the vacuum cleaner.
Leave for one (1) hour before switching the
vacuum cleaner back on.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
ROBLEM: Cleaner won’t pick up/loss of suction.
Cause: Dirt container not installed properly.
Solution: Review dirt container replacement.
Cause: Dirt container full or blocked.
Solution: Empty dirt container.
Cause: Clogged filters.
Solution: Remove, clean and replace filters.
ROBLEM: Accessories won’t pick up.
Cause: Accessories are not attached correctly.
Solution: Refer to section 5.
Cause: TurboBrush / TurboTool is clogged.
Solution: Refer to section 7.
Cause: Hose / Stretch Hose is not installed correctly.
Solution: Refer to section 7.
ROBLEM: Dust escaping from the vacuum cleaner.
Cause: Dirt container full.
Solution: Empty dirt container.
Cause: Dirt container not installed correctly.
Solution: Review dirt container replacement.
Cause: Hose / Stretch Hose is not installed correctly.
Solution: Review installation.
Cause: Filter not installed completely.
Solution: Remove, clean and replace filters.
!
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 8

10. UK Service & Help
Vax Care 0870 6061248
Monday-Friday 9.00am to 8.00pm.
Any queries or concerns about using the Vax, call the Vax
Careline. Calls are charged at the UK national rate.
lease make a note of the serial number and model
number of the carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For the
nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
11. Technical Specification
Voltage: 220-240V ~50Hz
Wattage: 2000W
Capacity: 1.9 litres approx
Filters: Central filter - wipe clean
re-motor filter - washable
ost-motor filter - washable
Cord length: 4.3m approx
Weight: 5.6kg
Subject to technical change without notice.
9
Vax Careline 0870 606 1248
troubleshooting
!
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 9

www.vax.co.uk
10
This page has been left intentionally blank
uk service & help / technical specification
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 10

11
Vax Careline 0870 606 1248
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 11

---
EEC STATEMENT OF COM LIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that
the V-112AA Ultrixx Range is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
EMC: 204/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. lease recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: [e-mail] - website: www.vax.co.uk
Vax V-0112AA User Guide:V-112AA User Guide 15/12/2008 09:50 Page 12