Vax C91-P2 SERIES User manual

12
7 6
5
1
2
5
6
3
4
5
11
1. Parts Overview
The Unit
1On/Off Button
Insert the plug into the electrical outlet. Press the
on/off switch on the top of the vacuum cleaner, to
switch the vacuum cleaner on and press the button
again to turn the vacuum cleaner off.
2Post-motor filter cover
3Plug
4Floor tool parking slot
For convenience there is a parking slot located at the
rear of the vacuum cleaner where the Floor Tool can
be parked for carrying and storage.
5Pre-motor filter
Located inside the dirt bin.
6Dirt container
7Hose inlet
8Carry handle
Located on the top of the unit, used to move the
vacuum cleaner from room to room.
9Auto-Cord rewind
To rewind the power cord, press the cord rewind
button, located on the top of the vacuum cleaner
10 Variable power
Power can be increased or reduced for greater
suction control
11 Dirt bin quick release button
Hold the dirt container over a bin and press the
release button.
12 Dirt Container Carry Handle
Use the carry handle located on the front of the dirt
bin to carry the dirt container.
Retain this guide for future reference.
powerpower22
Bagless cylinder
Vax model number: C91-P2 & C90-P2 SERIES instruction manual
Vax Careline: (UK) 0844 412 8455
(ROI) 1-800 928 308
vax.co.uk
8
9
10
What is your vax’s model number?
C 9 P 2
--
What is your vax’s serial number?
(on the base of your cleaner)
-----
Note this down in case you need it in future
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 1

vax.co.uk
To replace or purchase parts for your vacuum
cleaner, please visit our website:
vax.co.uk
If your Vacuum Cleaner or Accessories are Damaged/Faulty
Please Call our Vax Careline on: 0844 412 8455
!
Your Filters:
2parts overview
Replacement filter kits are available at vax.co.uk
KEEP YOUR VAX LIKE NEW!
14
15
16
18
19
13
25
26
24
The Accessories
13 Hose
14 Dusting brush
For delicate surfaces.
15 Crevice tool
For crevices, corners and cracks
16 Upholstery tool
For carpet, upholstery and stairs etc.
17 TurboTool (Some models only)
Perfect for picking up pet hair
18 Combination floor tool (Some models only)
For carpet and rug cleaning: Press the rocker switch
on the Combination floor tool to raise the brushes.
For hard floor cleaning: Press the rocker switch on the
Combination floor tool to lower the brushes.
19 Telescopic extension tube
The telescopic tube can be lengthened or shorted by
pushing the button in and sliding the tube apart or
together as required. The small tools can be stored on
the telescopic tube.
20 TurboTool connector (Some models only)
I PORTANT: The connector must be added to
the hose handle before the TurboTool may be
attached.
21 Stretch Hose (Some models only)
For full height stair cleaning.
NOTE: This should not be used as the main hose.
The stretch hose is recommended to be used for stair
cleaning. The unit should always be positioned at the
bottom of the stairs
22 Hard Floor Tool (Some models only)
For parquet and laminate flooring.
23 Turbo Brush (Some models only)
NOTE: ot recommended for hard floors.
F or large carpeted areas.
24 HEPA pre-motor filter
25 Pre-motor filter mesh shroud
26 Foam post-motor (Some models only)
anti-bacterial filter (Some models only)
I PORTANT: The condition of the filters affects
the performance of your vacuum cleaner. Please
check and wash filters periodically (depending on level
of use). For full cleaning instructions see page 4-5.
I PORTANT: Do not use the vacuum cleaner
without all the filters in place.
!
!
17
!
20
23
21
22
PLEASE NOTE: some parts may vary according to model. Please check inside flap of box for more details.
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 2

WARNING: Always switch off and unplug the vacuum cleaner from the electrical outlet before assembling, opening
or emptying the dirt container, or before connecting/ disconnecting the attachments.
!
3
assembly / attachments / operation / storage
NOTE: Fully unwind the
power cord. A yellow mark on
the power cord indicates the
recommended cord length.
Do not exceed the cord
length beyond the red mark.
NOTE: When rewinding the power cord, guide the cord
with one hand, This will prevent the cord from whipping
which could cause damage or injury.
NOTE: For convenience there is a parking slot located at
the rear of the vacuum cleaner where the floor tool and
hose can be parked for carrying and storage.
CLICK!
19
19
18
2. Assembling your vacuum cleaner
3. Choose the attachments for the job:
4. Operating the appliance
5. Packing away and storage
I PORTANT: Always unplug the vacuum from the electrical outlet and rewind the power cord as directed before
storing.
!
Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 3

vax.co.uk
4dirt container / filters
6. Dirt Container: Maintenance
Emptying the Dirt Container
Cleaning the dirt bin
7. The Filters: Maintenance
Cleaning the HEPA Pre- otor Filter
I PORTANT : Always switch off and unplug the vacuum cleaner from the electrical outlet before removing the Dirt
Container.
!
I PORTANT : Do OT use the
vacuum without ALL of the
filters in place.
Vax recommends that the pre- and
post-motor filter should be checked and
cleaned periodically depending on the
frequency of use and the volume of dirt
being picked up on each occasion.
NOTE : Both Pre- and Post-Motor Filters
can be rinsed in warm water (max 40°C).
Allow to air dry for 24 hours before
replacing. Do OT use any detergents or
boiling water to wash the filters.
I PORTANT: Your vax vacuum cleaner is fitted with high performance filters it is essential that these are well
maintained and cleaned according to the following instructions.
!
!
24
TAP
1
2
TAP
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 4

5
filters / clearing blockages
Cleaning the Post- otor Filter NOTE : This is located at the rear of the vacuum cleaner.
8. Clearing Blockages
Hose Blockages
The flexible hose may be disconnected from the vacuum
cleaner. Carefully remove any blockages found and
reconnect hose securely.
Clearing debris from the TurboTool (Some models only)
OTE: Switch the cleaner off and disconnect the power
plug from the electrical outlet.
Removing debris from the TurboBrush (Some models only)
The brushbar will stop rotating if it is blocked during
operation by vacuuming up foreign objects, or if strands of
carpet are wrapped around it.
Switch the vacuum cleaner off and disconnect the power
plug from the electrical outlet.
Lay the TurboBrush floor head on a flat surface and turn
over to expose the brushbar. Using a pair of scissors, cut
through any threads or hairs caught by the brushbar that
have wrapped around the guides (Fig.7/4).
Accessory Blockages
Remove accessory from hose handle/ tube. Carefully
remove the blockage and return to the cleaner.
24
WARNING : To reduce the risk of electric shock, the power cord must be
disconnected before performing maintenance/ troubleshooting checks.
Turn the vacuum cleaner off and unplug from the electrical outlet.
!
TAP
locking ring
tabs
Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 5

vax.co.uk
6FAQ
WARNING: to reduce the risk of personal injury, unplug the vacuum cleaner before performing
maintenance/troubleshooting checks.
!
9. FAQs
Is there an accessory missing?
• Check the ‘Parts Overview’ page in this guide to make
sure that the part is definitely included with your unit.
• If it is missing, please call our Vax Careline to order a
replacement: 0844 412 8455 or visit vax.co.uk to order
online.
Why won’t the vacuum cleaner pick up?
• The filters may be clogged: Refer to ‘The Filters:
Maintenance’ (Page 4).
• The Dirt Container is full or blocked: Refer to ‘Dirt
Container: Maintenance’ (Page 4).
• The Dirt Container may be incorrectly installed: Refer to
‘Dirt container: Maintenance’ (Page 4).
Why is dust escaping from the vacuum?
• The filters may not be installed correctly. Refer to ‘The
Filters: Maintenance’ (Page 4).
• The Dirt container may be incorrectly installed: Remove
the Dirt Container from the unit by lifting the Dirt
Container release handle (12) and reattach it to the unit,
ensuring it is locked firmly back into place.
• The filters may be clogged: Refer to ‘The Filters:
Maintenance’ (Page 4).
What do I do if an accessory/the unit becomes
damaged or broken?
• Visit vax.co.uk for parts and spares.
• Please call our Vax Careline to purchase new spares or
order a replacement:
0844 412 8455
Why won’t the accessories pick up properly?
• The accessory may be blocked: Refer to ‘Cleaning
Blockages’ (Page 5).
• The accessory may be faulty: call our Vax Careline to
order a replacement:
0844 412 8455
Why will the vacuum cleaner not run?
• It may not be plugged into the electrical outlet correctly:
Ensure that the plug is pushed into the electrical outlet
securely.
• The electrical outlet may not be working: Check the fuse
or breaker and consult an electrician.
• The motor Thermostat may have tripped: Switch off and
unplug the vacuum cleaner. Leave for one hour before
switching the vacuum cleaner back on.
If none of these questions apply to you, or for further
assistance please call our Vax Careline team on:
0844 412 8455
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 6

7
safety information
10. Safety Information
For Household Use Only
When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:
1. Only use the vacuum cleaner indoors on dry surfaces.
2. Turn off the vacuum cleaner controls before
connecting or disconnecting from the mains supply.
3. Always unplug the vacuum cleaner before connecting
or disconnecting the vacuum hose and accessories.
4. Children should be supervised to ensure that they do
not play with the appliance.
5. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
6. Use only as described in this manual.
Use only the manufacturer’s recommended
attachments.
7. Do not use the vacuum cleaner if it has been dropped,
damaged, left outdoors or dropped into water. Do not
use the vacuum cleaner with a damaged cord or plug.
If the supply cord or plug is damaged, it must be
replaced by the manufacturer or a recommended
Service Agent to avoid hazard and invalidating the
guarantee.
8. Do not pull or carry by the cord. Do not use the cord as
a handle, close a door on the cord or pull the cord
around sharp edges or corners. Do not run the vacuum
cleaner over the cord. Keep the cord away from heated
surfaces.
9. Do not handle the plug or vacuum cleaner with wet
hands. Do not use outdoors or on wet surfaces.
10.Do not put any objects into openings. Do not use with
any openings blocked and do not restrict air flow. Keep
all openings free of dust, lint, hair or anything that may
reduce airflow.
11.Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.
12.Do not pick up hot coals, cigarette butts, matches or
any hot, smoking or burning objects.
13.Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc) or use in the
presence of explosive liquids or vapours.
14.Do not vacuum up harmful or toxic material (chlorine
bleach, ammonia, drain cleaner, etc).
15.Do not vacuum up hard or sharp objects such as glass,
nails, screws, coins, etc.
16.Do not use without the filters in place.
17.Take extra care when vacuuming on stairs.
18.Keep vacuuming area well lit.
19.Store the vacuum cleaner indoors in a cool, dry area.
20.Turn off the on/off switch before unplugging the
vacuum cleaner.
21.Use only CE-approved 13 amp extension cords. on-
approved extension cords may overheat. Care should
be taken to arrange the cord so that the cord cannot
be pulled or tripped over.
WARNING: Always switch off and unplug the
vacuum cleaner from the electrical outlet
before assembling, opening or emptying the dirt
container, or before connecting/disconnecting the
attachments.
CAUTION: The vacuum cleaner is a very powerful
unit. Before plugging the cord into the electrical
outlet, make sure the switch is in the ‘off’ position. Hold
the vacuum cleaner firmly when starting and in use.
I PORTANT: If the inlet, hose or telescopic tube is
blocked, switch off the vacuum cleaner and remove
the blockage(s) before re-starting the vacuum cleaner.
I PORTANT: Washing filters improves vacuum
performance. Make sure all the filters are
completely dry before inserting back into the vacuum
cleaner.
This vacuum cleaner is intended for household use only
and not for commercial or industrial use.
!
!
!
!
otor Thermostat
I PORTANT: The motor is equipped with a
thermal cut-out. If for any reason, the vacuum
cleaner should over-heat, the thermostat will
automatically turn the unit off. Should this occur,
unplug the vacuum cleaner from the electrical outlet
and turn off the switch. Remove the dirt container
and empty. Clean the filters. Allow the cleaner to cool
for approximately one (1) hour. To re-start, plug into
an electrical outlet and switch back on.
!
Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 7

11. UK Service & Help
(UK) 0844 412 8455
(ROI) 1-800 928 308
onday-Friday 8.30am to 6.30pm
Saturday-Sunday 9.00am to 5.00pm
Any queries or concerns about using your Vax, call the Vax Careline. Please make a note of the model number and serial
number of your Vax before calling. For the nearest Vax Service Agent, please call the Vax Careline or visit vax.co.uk
11. Consumables
To purchase spares and accessories, please visit vax.co.uk
Filter Kit (1-9-128628-00)
12. Technical Specification
Voltage: 220 - 240 ~ 50 Hz
Wattage: 2000W / 2200W (depending on model)
Capacity: 2.6 litres
Filters: HEPA pre-motor filter – washable
Pre-motor filter mesh shroud - washable
Anti-bacterial filter - washable (some models only)
Foam post-motor filter - washable (some models only)
Cord Length: 6m (approx)
Weight: 6.4 Kg (approx)
Subject to technical change without notice
13. EEC Statement of Compliance
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
C90-P2/C91-P2 Power 2 Series is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
E C: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
vax.co.uk
8uk service / technical specification / eec statement
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 8

9
This page has been left intentionally blank
Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 9

vax.co.uk
10
This page has been left intentionally blank
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 10

11
This page has been left intentionally blank
Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 11

ppower
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: inf[email protected]o.uk - website: vax.co.uk
C91-P2 & C90-P2 Series User Guide.q d:C91-P2 Series User Guide 29/1/10 14:44 Page 12