Vaxcel F0092 User manual

PAGE: 1 / 9
210413
Model No.: F0092
ORIGINAL VAXCEL CEILING FAN LIMITED LIFETIME WARRANTY
The limited lifetime warranty covers this fan, for residential use by the original purchaser, against defects in material or
workmanship as follows:
If your fan motor fails at any time during the lifetime of the original purchaser due to defects in material or workmanship,
we will provide a replacement part free of charge.
If your fan motor fails at any time within one year after the original date of sale to the original purchaser due to defects
in material or workmanship, we will provide labor to repair the defect, with the exception of take down/reinstallation,
free of charge. The original purchaser will be responsible for all labor costs after this one year period.
If no replacement parts are provided for any part of your fan motor that fails at any time during your lifetime due to
defects in material or workmanship, we will refund the original purchase price of your fan.
If your fan blades, or any accessory, except glass globes and light bulbs, fails at any time within one year after the
original date of purchase due to a defect in material and workmanship, we will repair or, if we choose, replace the
defective blades, switch, or accessory free of charge, with the exception of take down/reinstallation services.
If the original purchaser ceases to own the fan, this warranty and any implied warranty, including but not limited to any
implied warranty of merchantability or fitness for a particular purpose, become void. This warranty and any implied
warranty, including but not limited to any implied warranty of merchantability or fitness for a particular purpose, do not
cover glass globes, light bulbs, or finish on any metal portions of the fan.
This warranty is in lieu of express warranties. The duration of any implied warranty of merchantability or fitness for a
particular purpose, with respect to any fan motor, blades, switch, or accessories, is expressly limited to the period of the
express warranty set forth above for such motor, blades, switch, or accessories.
This warranty excludes defects, malfunctions, or failures of any fan that are caused by repairs by persons not authorized
by us, use of parts or accessories not authorized by us, mishandling, improper installation, modifications or damage to
the fan while in your possession, or unreasonable use, including failure to provide necessary maintenance.
In no event shall VAXCEL be liable for consequential or incidental damages.
Some states do not allow the exclusion or limitation of consequential or incidental damages, in which case the above
limitation or exclusion may not apply.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
LIMITED LIFETIME WARRANTY

10 1211
25
78
9
6
34
Unpack your fan and check the contents. You should have the following items.
1.) Hanger Bracket
2.) Canopy
3.) Decorative Cap (Comes in a separate bag)
4.) Downrod Stand Cover
5.) Downrod Set (Included Hanger Ball, 6” Downrod, Hanger Pin & Lock Pin)
6.) Fan Motor Assembly with LED Module
7.) Fan Blades (8 PCS)
8.) Glass Shade
9.) Assembly Kit
10.) Remote Control Set (Included Transmitter & Batteries & Screws)
11.) Blade Balancing Kit
12.) Installation Instructions
Package Contents:
1
Dimension Reference (Installed with 6” Downrod):
A. 15” B. 11-1/2” C.68” D. 5”
C
B
D
A
X25
1.5V
1.5V
CCT
PAGE: 2 / 9
210413

Exploded View Detail
Downrod Mount
Slope Ceiling Mount (Up to 23 degrees)
Dual Mount Drawing
Hanger Bracket
Canopy
Downrod
Downrod Stand Cover
Hanger Ball
Hanger Pin
Decorative Cap
Collar
Lock Pin
Blade Holder
Glass Shade
Fan Blade
Fan Motor Assembly
LED Module
PAGE: 3 / 9
210413

Safety Instructions
READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN TO
INSTALL THE FAN AND SAVE INSTRUCTIONS.
All set screws of the fan must be checked and retightened where necessary before installation.
To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets,
balancing the blades or cleaning the fan. Do not insert foreign objects between rotating fan blades.
Before changing the fan direction, turn off the fan and wait for the fan blades to stop completely.
The safeguards provided by these safety instructions and by the separate installation instructions are
not meant to cover all possible conditions and situations that may occur. It must be understood that
common sense, caution and care are factors which can not be built into this product. These factors
must be supplied by the person(s) installing, caring for and operating the fan.
TO AVOID RISK OF ELECTRIC SHOCK, BE SURE TO SHUT OFF POWER AT THE MAIN
FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS
FIXTURE. TURNING OFF THE ELECTRICAL POWER BY USING THE LIGHT SWITCH
IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
TO REDUCE THE RISK OF INJURY, INSTALL THE FAN SO THAT THE BLADES ARE
AT LEAST 7 FEET (2.1 METERS) ABOVE THE FLOOR AND AT LEAST 18 INCHES
(0.5 METERS) FROM THE TIP OF THE BLADES TO THE WALL.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT
TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT" AND USE MOUNTING
SCREWS PROVIDED WITH THE OUTLET BOX.
THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL
CODE, ANSI/NFPA 70-1999 AND LOCAL CODES. IF YOU ARE UNFAMILIAR WITH THE
METHODS OF INSTALLING ELECTRICAL WIRING, SEEK THE SERVICES OF A
QUALIFIED LICENSED ELECTRICIAN.
WARNING
PAGE: 4 / 9
210413

NOTE: The fan weight is 23.59 lbs (10.7 kg). Be sure the outlet box you are using is securely attached to the building
structure and can support the full weight of the fan. Failing to do so can result in serious injury.
INSTALLATION INSTRUCTIONS
IMPORTANT:
BEFORE YOU BEGIN INSTALLING THE FAN, CAREFULLY READ ALL INFORMATION IN
SAVE ALL INSTRUCTIONS.
Thread the motor wires through the
downrod stand cover, decorative
cap (Making sure the smooth side
of decorative cap is facing
downward.), canopy and downrod.
Hanger Pin
Lock Pin
Remove the lock pin and take off
the hanger pin.
Fig.3
Loosen the collar screws out part way.
Insert the downrod into the collar.
Slide hanger pin through holes of
collar and downrod.
Hang the fan on hanger bracket, and
make sure the slot of hanger ball is
snapped into the chip of hanger
bracket exactly.
Note: For slope ceiling installation,
make sure the slot of hanger ball and
the chip of hanger bracket face down.
Tighten the two collar screws.
Slide lock pin into hanger
pin until it is locked into position.
Installation Steps :
Fig.1
Turn OFF the electric circuit at the
main fuse or circuit breaker box.
THE SAFETY
INSTRUCTIONS AND INSTALLATION INSTRUCTIONS. IF IN DOUBT, CONSULT A QUALIFIED
ELECTRICIAN.
Lock Pin
Fig.6
Collar Screws
Hanger Pin
Collar
Fig.5
Motor Wires
Downrod
Downrod Stand
Cover
Canopy
Decorative Cap
Collar
Fig.4
Motor Wires
Downrod
Downrod Stand
Cover
Canopy
Decorative Cap
PAGE: 5 / 9
Fig.7
Slot
Chip
Hanger Bracket
Ceiling
Hanger Bracket
Ceiling Joist
Wood Member
(2" x 4" Approx.)
Junction Box
Safety Cable Hook
Ceiling
Hanger Bracket
Ceiling Joist
Wood Member
(2" x 4" Approx.)
Junction Box
Fig.2
Tighten the hanger bracket to the outlet box with two mounting screws. (Make sure
the outlet box is securely installed so that it will be able to support at least the
fan weight.) Attach the safety cable hook to the ceiling and make sure the safety
cable hook is covered by the fan canopy.
Note: 1. For slope ceiling installation, make sure that the chip of the hanger
bracket is toward the floor.
2. The fan is too heavy, use this kind of hanger bracket only.
210413

For LED module replacement only:
Separate the male from female terminals on the wires connecting the LED module to motor.
Take a new LED module and connect the white (neutral) wire from fan motor assembly to
the white (neutral) wire from the LED module and connect the blue (hot) wire from fan motor
assembly to the black (hot) wire from LED module.
Fig.8
Connect the white (neutral)
wire from motor to the white
(neutral) wire from the
outlet box with a wire
connector.
Connect the black (hot) wire
(This is for fan and light control)
from motor to the black (hot) wire
from outlet box with a wire
connector.
Bla
Black
ck
Green
White
White
Grounding
Green
*** After making the wire connections, the wires should
be spread apart. The white (neutral) conductor and
green (grounding) conductor on one side and the
black (hot) conductor on the other side of the outlet
box.
*** The wire connection points should be turned upward
and pushed carefully up into outlet box.
Connect three
ground wires (Green
or bare copper) coming
from outlet box,
downrod and hanging
bracket with a wire
connector.
Slide the canopy up to ceiling and over the two
canopy screws on hanger bracket. Rotate canopy
clockwise, next, while holding the canopy with one
hand, slide the canopy cover over the screws and
rotate counterclockwise until tight.
Note: Adjust the canopy screws as necessary
until the canopy and canopy cover are snug.
Tighten blades to blade brackets by using blade holder screws and washers.
Note: The blades shape should be same with the blade holders shape. (Fig.11a)
Canopy Screw
Hanger Bracket
Canopy
Canopy Cover
Fig.10
Blade Holder
Blade
Washers
Blade Holder
Screws
Fig.11
PAGE: 6 / 9
Fan Motor
Assembly
LED Module
LED Module
Screw
Female Terminal
Male Terminal
Fig.12
Hang the safety cable into the safety cable hook, tighten the safety
cable to the safety cable hook by using the zip-tie.
Fig.11a
Safety Cable Hook
Safety Cable Zip-tie
Fig.9
210413

Turn ON the electric circuit at the
main fuse or circuit breaker box.
Attach the glass shade to the plastic
holder by aligning studs and slots,
and then turn it clockwise until it is
locked in place.
Fig.14
Transmitter
Wall Bracket
Anchor
Screw
Fig.16
CCT
Install the transmitter wall bracket in wall by two anchors and two screws
and hang transmitter in it carefully .
PAGE: 7 / 9
Glass
Shade
Slot
Plastic
Holder
Fig.13
1
3
6
2
4
5
7
8
Fig.15
Remote Control Transmitter
CCT
Remote controller
Install two 1.5 volt batteries (type AAA, included) to the remote controller.
The remote buttons instruct as below:
1. " " Reverse button:
Press this button to control fan direction.
The lateness of reverse function is normal, Please wait for a moment.
2. Fan speed:
1 = minimum speed 2 = low speed
3 = medium low speed 4 = medium speed
5 = medium high speed 6 = high speed
3. " " Button:
Press this button to turn the fan off.
4. Timer Control:
Press "1H","4H" or "8H" button to stop the fan speed after that period.
Press fan off button to stop the timer control, and fan also will be turn off.
5. " " button:
Press this button quickly to turn on or turn off the light. Press and hold this button to
dim or brighten lights to the desired level then release, and the brightness level will be
memorized.
6. " " Breese button:
Press breese button to control the fan speeds automatic cycle between 1 to 6 speeds with a 20-second frequency. And any other fan
speed button can be stop this function.
7. Vacation mode button: Press vacation mode button to turn on the light 5 minutes each 2 hours, any other button can be stop this
function.
8. " " button:
Press this button to change color temperature of fan light, there are total 5 levels color changing from 2700K,3000K,3500K,4000K
to 5000K.
Note:
1. This remote controller has memory function setting. The fan will operate at the same speed and the fan light will stay at the
same brightness as the last time the power supply was turned off.
2. Included transmitter matched with receiver in the motor.
3. One transmitter can be compatible with 4pcs ceiling fan and every ceiling fan can be compatible with new transmitter
according press and hold the fan off button with 5 seconds until you hear the indicator sound of swoosh from the transmitter
and this step should be done within 30 seconds time frame after the main power is turned on.
210413

Troubleshooting Guide
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation
or wiring. If you experience any faults, please check this Troubleshooting Guide. If a problem cannot be
remedied or you are experiencing difficulty in installation, please call our Customer Service Department
(1-800-887-6326).
PROBLEM
1. If fan does not start:
2. If fan sounds noisy:
3. If fan wobbles:
4. If light does not work:
1. Check main and branch circuit fuses or circuit breakers.
2. Make sure that the wall control is turned "ON".
1. Make sure all screws in motor housing are snug. (not over tightened)
2. Make sure the screws which attach the fan blade holders to the motor are tight.
3. Make sure wire nut connectors at the back of light kit. are not rattling against each
other or against the interior wall of the back of light kit.
CAUTION: Make sure main power is turned off before accessing light kit.
4. Check to be sure the light kit is secured on motor tightly.
5. Some fan motors are sensitive to signals from Solid State variable speed
controls.
6. Allow "break-in" period of 24 hours. Most noises associated with a new fan will
disappear after this period.
All blades are weighed and grouped by weight. Natural woods vary in density
which could cause the fan to wobble even though all blades are weight-matched.
The following procedures should eliminate most of the wobble. Check for wobble
after each step.
1. Check that all blades are screwed firmly into blade holders.
2. Check that all blade holders are tightened securely to motor.
3. Make sure that canopy and hanger bracket are tightened securely to ceiling
outlet box and outlet box is mounted firmly to ceiling joist.
4. Most wobble problems of fan are caused when blades are not in equal level. To
check the blade levels, select a point on the ceiling above the tip of any blade.
Measure the distance from the ceiling to the blade tip, to an accuracy of 1/8
inch. Rotate the blades until the next blade is in the measuring position. Repeat
measurement for each blade. If all blade levels are not equal, you can adjust
blade levels by the following procedure. To adjust a blade tip down, insert a
washer (not supplied) between the blade and blade bracket at the screw
closest to the motor. To adjust a blade tip up, insert washer (not supplied)
between the blade and blade bracket at the two screws farthest from the motor.
5. Interchanging two adjacent blades could redistribute the weight and possibly result
in smoother operation.
1. Check blue wire from fan to make sure it is connected to hot wire from supply wire
coming out of the ceiling.
2. Check for loose or disconnected wires in fan light kit.
SUGGESTED REMEDY
PAGE: 8 / 9
210413

DYNAMIC BLADE BALANCING KIT
PREFACE
Your ceiling fan may sometimes have wobbling problems when operating due to irregularity in the
blades or the blade brackets. Improper assembly in the mounting system may cause some additional
problems. This balancing kit can be used to fix wobbling problems.
DYNAMIC BLADE BALANCING KIT FOR CEILING FANS
1. Make sure that all blades are firmly screwed into the blade brackets.
2. Make sure that all blade brackets are firmly secured to the motor housing.
3. By looking up at the fan from below, check and be certain that none of the blade brackets are bent
and that none of the blades are out of position.
4. Use a yardstick to check the blade tracking. Put the yardstick up against the ceiling vertically and
against the outside leading edge of a blade. Note the distance of the edge of blade to the ceiling.
Carefully turn the blades slowly by hand to check the remaining blades. All distances should be
the same.
Operate the fan ten minutes. After following all the steps and if the wobbling problem is not solved, a
dynamic balancing needs to be done with balancing kit. Follow the procedure listed below:
● Turn the fan off. Select one blade and place the plastic clip on it, with the plastic clip located
halfway between the blade bracket and the blade tip on the edge of the blade.
Caution: The plastic clip should be placed on the windward edge of the blade for fear of
clip flying off.
● Turn the fan on (set the speed that causes the wobble most). Observe if the wobble is better or
worse. Turn the fan off and move the clip to the next blade. Do the same for all blades and note
on which blade the clip reduces the wobble most. Place the clip on the blade which showed the
most improvement. Move the clip inward and outward on this blade and operte the fan to find
the position where the clip gives the most improvement.
Caution: Stay clear of the blades. If the clip, for any reason, is not secure, injury could result.
● Once the exact position is determined, place a weight on the top of the blade, on its centerline and
as close as possible to the clip. Peel the paper off of the back of the weight and press firmly to
ensure that it is securely attached to the blade. Remove the clip.
Caution: Clean the surface of fan blade before placing the balancing weight so that the
balancing weight will be firmly attached to it.
BALANCING WEIGHT
MEASURING
POINT
YARDSTICK
PLASTIC CLIP
CENTERLINE
COUNTER-
CLOCKWISE
1
2
3
4
5
6
7
8
9
PAGE: 9 / 9
210413
Table of contents
Other Vaxcel Fan manuals
Popular Fan manuals by other brands

Monte Carlo Fan Company
Monte Carlo Fan Company Jovie 3JVR52 Series Owner's guide and installation manual

Applica
Applica WCF600 Use and care book

Klimawent
Klimawent STRONG-5000-S Use and maintenance manual

S&P
S&P PCD110XP quick start guide

Munters
Munters WM36KCB-6PK Series instruction manual

Panasonic
Panasonic FV-0510VSC1 Service manual