Vaxcel F0106 User manual

PAGE: 1 / 8
Model No.: F0106 F0107
ORIGINAL VAXCEL CEILING FAN LIMITED LIFETIME WARRANTY
The limited lifetime warranty covers this fan, for residential use by the original purchaser, against defects in material or
workmanship as follows:
If your fan motor fails at any time during the lifetime of the original purchaser due to defects in material or workmanship,
we will provide a replacement part free of charge.
If your fan motor fails at any time within one year after the original date of sale to the original purchaser due to defects
in material or workmanship, we will provide labor to repair the defect, with the exception of take down/reinstallation,
free of charge. The original purchaser will be responsible for all labor costs after this one year period.
If no replacement parts are provided for any part of your fan motor that fails at any time during your lifetime due to
defects in material or workmanship, we will refund the original purchase price of your fan.
If your fan blades, or any accessory, except glass globes and light bulbs, fails at any time within one year after the
original date of purchase due to a defect in material and workmanship, we will repair or, if we choose, replace the
defective blades, switch, or accessory free of charge, with the exception of take down/reinstallation services.
If the original purchaser ceases to own the fan, this warranty and any implied warranty, including but not limited to any
implied warranty of merchantability or fitness for a particular purpose, become void. This warranty and any implied
warranty, including but not limited to any implied warranty of merchantability or fitness for a particular purpose, do not
cover glass globes, light bulbs, or finish on any metal portions of the fan.
This warranty is in lieu of express warranties. The duration of any implied warranty of merchantability or fitness for a
particular purpose, with respect to any fan motor, blades, switch, or accessories, is expressly limited to the period of the
express warranty set forth above for such motor, blades, switch, or accessories.
This warranty excludes defects, malfunctions, or failures of any fan that are caused by repairs by persons not authorized
by us, use of parts or accessories not authorized by us, mishandling, improper installation, modifications or damage to
the fan while in your possession, or unreasonable use, including failure to provide necessary maintenance.
In no event shall VAXCEL be liable for consequential or incidental damages.
Some states do not allow the exclusion or limitation of consequential or incidental damages, in which case the above
limitation or exclusion may not apply.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
LIMITED LIFETIME WARRANTY
220407

Unpack your fan and check the contents. You should have the following items.
1.) Mounting Plate
2.) Fan Motor Assembly with Receiver of Remote Controller
3.) Fan Blades (4 PCS)
4.) Connect Plate of Light Kit
5.) Light Kit with LED Module
6.) Glass Shade
7.) Assembly Kit
8.) Installation Instructions
9.) Remote Control Set (Includes Transmitter & Battery & Screws & Remote Control Instructions)
Dimension Reference:
PAGE: 2 / 8
Package Contents:
1
2
3
4
7
6
5
89
Remote Control Instructions
Installation Instructions
X13
A
B
F
A. 11" B. 7-1/2" C. 9-1/2" D. 6" F. 52"
220407

Exploded View Detail
Mounting Plate
Fan Motor Assembly with
Receiver of Remote Controller
Fan Blade
Glass Shade
Connect Plate of Light Kit
PAGE: 3 / 8
Light Kit with LED Module
220407

Safety Instructions
READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN TO
INSTALL THE FAN AND SAVE INSTRUCTIONS.
All set screws of the fan must be checked and retightened where necessary before installation.
To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets,
balancing the blades or cleaning the fan. Do not insert foreign objects between rotating fan blades.
Before changing the fan direction, turn off the fan and wait for the fan blades to stop completely.
The safeguards provided by these safety instructions and by the separate installation
instructions are not meant to cover all possible conditions and situations that may occur. It must be
understood that common sense, caution and care are factors which can not be built into this product.
These factors must be supplied by the person(s) installing, caring for and operating the fan.
TO AVOID RISK OF ELECTRIC SHOCK, BE SURE TO SHUT OFF POWER AT THE MAIN
FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS
FIXTURE. TURNING OFF THE ELECTRICAL POWER BY USING THE LIGHT SWITCH
IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
TO REDUCE THE RISK OF INJURY, INSTALL THE FAN SO THAT THE BLADES ARE
AT LEAST 7 FEET (2.1 METERS) ABOVE THE FLOOR AND AT LEAST 18 INCHES
(0.5 METERS) FROM THE TIP OF THE BLADES TO THE WALL.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT
TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT" AND USE MOUNTING
SCREWS PROVIDED WITH THE OUTLET BOX.
THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL
CODE, ANSI/NFPA 70-1999 AND LOCAL CODES. IF YOU ARE UNFAMILIAR WITH THE
METHODS OF INSTALLING ELECTRICAL WIRING, SEEK THE SERVICES OF A
QUALIFIED LICENSED ELECTRICIAN.
WARNING
PAGE: 4 / 8 220407

Installation Steps :
Fig.1
Turn OFF the electric power at the
main fuse or circuit breaker box.
Left fan motor assembly
and hang on mounting
plate with hook provided,
through one of the two
holes in canopy. This will
allow for hands-free wiring.
CAUTION: Use only a side
with hole in canopy, not
hook slot.
PAGE: 5 / 8
INSTALLATION INSTRUCTIONS
NOTE: The fan weight is 15.65 lbs (7.1 kg). Be sure the outlet box you are using is securely attached to the building
structure and can support the full weight of the fan. Failure to do so can result in serious injury.
Screw the safety cable hook to the ceiling outlet box. (Make sure the outlet box
is securely installed so that it will be able to support at least the fan weight.)
Pull the wires from outlet box through the center hole of mounting plate. Attach the
mounting plate to the outlet box by using two washers and mounting screws.
WARNING: MOUNT ONLY TO AN OUTLET BOX MARKED "ACCEPTABLE
FOR FAN SUPPORT"!
.
Fig.2
Safety Cable Hook
Ceiling
Mounting Plate
Outlet Box
Washer
Mounting Screw
Fig.3
Mounting Plate
Fan Motor
Assembly
Fig.4
IMPORTANT:
BEFORE YOU BEGIN INSTALLING THE FAN, CAREFULLY READ ALL INFORMATION N THE SEPARATE
SHEET "SAFETY INSTRUCTIONS" AS WELL AS THE FOLLOWING "INSTALLATION INSTRUCTIONS". IF IN
DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
SAVE ALL INSTRUCTIONS.
Fig.6a Antenna
SUR Switch
Transmitter
Receiver
SUR
ON
ON SUR
Pull the safety cable
out of fan motor
assembly and
through the center
hole of mounting
plate, then hang it
into the safety cable
hook.
Safety Cable
Hook
Mounting
Plate
Fan Motor
Assembly
Fig.5
Safety Cable
ON SUR
Fan Motor
Assembly
Receiver
Fig.6
Note: The ceiling fan may work abnormally if there is interference from other remote controls.
Both the transmitter and receiver have a 4-key
unit code on each SUR Switch (Fig.6) and by
default, all keys are pre-set to the "off" position.
This means that the transmitter and receiver are
already paired together. However, if you have
multiple fans and remote controls and want to
avoid interference between them, you can "pair"
other transmitters and receivers together by
adjusting the SUR switches, so the same
numbered keys are in the "ON" position
on both (Fig.6b).
220407

Make wire connections:
1). The white motor wire to the
white wire from the outlet box
with a wire connector.
2). The black motor wire to the
black wire from the outlet box
with a wire connector.
3).The ground wire from the
outlet box to the ground
wire from the mounting
plate with a wire connector.
PAGE: 6 / 8
There are four mounting plate screws
and lock washers. Remove two screws
and lock washers from the mounting
plate (one from each side) and loosen
the other two remaining screws. Align
the “L shaped” slots of the canopy
with the two remaining screws on the
mounting plate and push the motor
assembly upwards to engage the slots
and turn clockwise to lock in place.
Tighten the screws and install the other
two mounting plate screws and lock
washers into the remaining holes of
the canopy and tighten.
Insert the fan blade through the slot
on the fan motor assembly and
fasten fan blade to the fan motor
assembly with screws. Repeat for
remaining fan blades.
Attach the glass shade to the connect
plate of light kit by aligning studs and
slots, and then turn it clockwise until it
is locked in place.
Remove three screws from
connect plate of light kit first.
Then connect the female
terminals from fan motor
assembly to male terminals
from LED module. Connect
the white (neutral) wire from
the light kit to white(neutral)
wire from connect plate of
light kit; connect the blue
(hot) wire from light kit to
Fan Blade
Fig.9 Blade Screw
Fan Motor
Assembly
Fig.12
Code example:
1-ON 2-OFF 3-ON 4-OFF on
both SUR Switches.
Note: If you have two ceiling fans
with 2 remote control units, set 2
different codes for each set of
transmitter / receivers.
Fig.6b
Remove one screw and loosen another
two screws from fan motor assembly first,
then thread the fan motor assembly wires
through connect plate of light kit, then
push the connect plate of light kit upwards
until the fan motor assembly screws insert
into the key hole slots of connect plate of
light kit, then rotate the connect plate of
light kit until it’s fixed on the fan motor
assembly bottom. Finally, secure the
connect plate of light kit to the fan motor
assembly bottom with previous screw
which was removed. Tighten the other
two fan motor assembly screws.
Wire Connector
Fig.7
Fan Motor
Assembly
Mounting Plate Mounting Screw
Fig.8
Fan Motor Assembly
Fig.11
Male Connector
Female
Connector
LED Module
Screw
blue (hot) wire from connect plate of light kit. Carefully put the
wires into the connect plate of light kit, then attach the light kit
onto the connect plate of light kit with the connect plate screws.
Glass Shade
Slot
Stud
Connect
Plate of
Light Kit
Fan Motor
Assembly
Fix Screw
Connect
Plate of
Light Kit
Fig.10
220407

Turn ON the electric power at the
main fuse or circuit breaker box.
Fig.14
PAGE: 7 / 8
Fig.15
Transmitter
Wall Bracket
Screw
Fig.16
Install the battery (9V, included) into the transmitter.
* Press "HI" button to turn on the fan at high speed.
* Press "MED" button to turn the fan in medium speed.
* Press "LOW" button to turn the fan in low speed.
* Press "FAN OFF" button to turn off the fan.
* Press "LIGHT ON/OFF" button to turn on or turn off the light.
* Press and hold the "DIMMER" button to dim or brighten lights to the desired level and
release, and the brightness level will be memorized. Turn on the light again, then fan light
will be restored to the brightness-level at which it was dimmed last time.
Note:
1. This remote controller has a memory function setting. The fan will operate at the same
speed and the fan light will stay at the same brightness-level as the last time the power
supply was turned off.
2. Compatible Wall Switch: Lutron SKU# S2-LFSQH-WH.
Install the transmitter wall bracket on the wall with two screws and place transmitter in it carefully.
Fig.13
Slide Switch
Reverse
Forward
The slide switch on connect plate of light kit
sets direction of fan rotation. Select the desired
direction of fan rotation. Push the slide switch
left for " Forward" and right for "Reverse”.
Note: Wait for fan to stop before reversing
the direction of blade rotation.
220407

PAGE: 8 / 8
Troubleshooting Guide
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation
or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any
faults, please check this Troubleshooting Guide. If a problem cannot be remedied or you are
experiencing difficulty in installation, please call our Customer Service Department (1-800-482-9235).
PROBLEM
1. If fan does not start:
2. If fan sounds noisy:
3. If fan wobbles:
4. If light does not work:
1. Check main and branch circuit fuses or circuit breakers.
2. Check line wire connections to fan and switch wire connections in switch
housing.
CAUTION: Make sure main power is turned off.
3. Make sure forward/reverse switch is firmly in left or right position. Fan will not
operate when switch is in the middle.
4. Make sure that the wall control is turned "ON".
1. Make sure all screws in motor housing are snug. (not too tight)
2. Make sure the screws which attach the fan blade bracket to the motor are tight.
3. Make sure wire connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before accessing switch
housing.
4. Some fan motors are sensitive to signals from Solid State variable speed
controls. DO NOT USE a Solid State variable speed control.
5. Allow "break-in" period of 24 hours. Most noises associated with a new fan will
disappear after this period.
All blades are weighed and grouped by weight. Natural woods vary in density
which could cause the fan to wobble even though all blades are weight-matched.
The following procedures should eliminate most of the wobble. Check for wobble
after each step.
1. Check that all blades are screwed firmly into blade brackets.
2. Check that all blade brackets are tightened securely to motor.
3. Make sure that canopy and mounting bracket are tightened securely to ceiling
junction box and junction box is mounted firmly to ceiling joist.
4. Most fan wobble problems are caused when blades are not equally level. To
check the blade levels, select a point on the ceiling above the tip of any blade.
Measure the distance from the ceiling to the blade tip, to an accuracy of 1/8
inch. Rotate the blades until the next blade is in the measuring position. Repeat
measurement for each blade. If all blade levels are not equal, you can adjust
blade levels by the following procedure. To adjust a blade tip down, insert a
washer (not supplied) between the blade and blade bracket at the screw
closest to the motor. To adjust a blade tip up, insert washer (not supplied)
between the blade and blade bracket at the two screws farthest from the motor.
5. If blade wobble is still noticeable, interchanging two adjacent (side by side)
blades can redistribute the weight and possibly result in smoother operation.
1. Check blue wire from fan to make sure it is connected to hot wire from house.
2. Check for loose or disconnected wires in fan switch housing.
3. Check for loose or disconnected wires in light kit.
4. Check for faulty the LED module.
CAUTION: Make sure main power is turned off before accessing switch
housing.
SUGGESTED REMEDY
220407