VDH MC 795D User manual

Description: MC 795D Hygrostat Doc.nr.: 053682
Type: MANUAL Number of pages: 16 Version: V1.1
File: Do053621.wpd
Software: MC795D Version: V1.03 By: HN Date: 08-02-2007
VDH Products BV - Roden - Holland Signed: File: Doc'05
MC 795D
Operating Manual
wall and panel mounting

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 2 of 16
The information contained in this document is assumed to be accurate. However VDH Products BV accepts
no liability for eventual mistakes or errors and has the right to change this document without notice.
Table of contents
1Technical specifications. .......................................................3
2Functional specifications. .......................................................4
3Control of the thermostat. ......................................................5
4Programming internal settings. ..................................................6
5Operation relay outputs. ........................................................8
6Sensor calibration. ............................................................9
7Alarms. .....................................................................9
8Advanced Programming. ......................................................10
9Front views. ................................................................14
10 Connection diagrams. ........................................................15
11 Dimensions. ................................................................16

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 3 of 16
1 Technical specifications.
General
Type : MC 795D
Wall mounting:
Housing : Grey plastic
Material : Polystyrol 454h KG 2 natur BASF
Dimensions : 213 x 180 x 85mm (whd)
Front : Polycarbonate (IP-44)
Panel mounting:
Housing : Steel plate panel
Material : Steel in silvergrey
Dimensions : 217 x 155 x 85mm (whd)
Panel cutout : min. 208 x 146mm (wh)
Front : Polycarbonate (IP-44)
Range : 0/+100% RH
Supply : 230 Vac; 50/60 Hz (-10/+5%).
Used power : 9 VA
Store temperature : -20/+60°C
Operation temperature : -20/+50°C
Operating rel. humidity : 10/+90 % RH not condensing
Accuracy : ± 0,5 % of the range
Front
Display : 4-number digital display for humidty read-out
4-number digital display for the setpoint
LED : F1 = LED Hygrostat 1 active
F2 = LED Hygrostat 2 active
F3 = LED Hygrostat 3 active
F4 = LED Hygrostat 4 active
= LED Night mode active
= LED Alarm active
S1 = LED Setpoint 1 in display
S2 = LED Setpoint 2 in display
S3 = LED Setpoint 3 in display
S4 = LED Setpoint 4 in display
Keys : ON/OFF = On/Off key controller
SETP = Setpoint push button
= Up key
= Down key
PRG = Program key
SENS = Sensor read-out key

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 4 of 16
In- and outputs
Sensors : Humidity sensor 1 (3-wire, V+=12V, Sign.:0-1V, 0V)
Humidity sensor 2 (3-wire, V+=12V, Sign.:0-1V, 0V)
Humidity sensor 3 (3-wire, V+=12V, Sign.:0-1V, 0V)
Humidity sensor 4 (3-wire, V+=12V, Sign.:0-1V, 0V)
Digital inputs : Night offset input (potential free input contact)
External alarm input (potential free input contact)
Analog output : 2x 0/+10Vdc, Rbmin 10Kohm, programmable.
Relay outputs : RY1 Alarm (C/NO/NC, 250Vac/10A not inductive)
Normally C-NO is closed, at alarm C-NC is closed.
The next relays have a central common;
RY2 Relay 2 programmable (NO, 250Vac/10A not inductive)
RY3 Relay 3 programmable (NO, 250Vac/10A not inductive)
RY4 Relay 4 programmable (NO, 250Vac/10A not inductive)
RY5 Relay 5 programmable (NO, 250Vac/10A not inductive)
2 Functional specifications.
To the MC 795D hygrostat a maximum of four humidty sensors can be connected. These sensors can
be used as control sensor, info sensor or alarm sensor.
A maximum for four different setpoints can be programmed.
The MC 795D has the control functions dehumidifying or humidifying. Also has the controller an alarm
relay, which becomes active as soon as the alarm levels are exceeded, a sensor is broken or the
external alarm input is closed.
The MC 795D has two analog outputs with a range of 0/+10Vdc. The function of these outputs can be
programmed as measuring signal, setpoint signal or a P(I) control for dehumidifying or humidifying.
The controller has two digital input contacts. The first contact is used as night offset input, the second
contact as external alarm.
The above mentioned settings are made via the Internal Parameters.
To allow also other combinations between setpoints, sensor and relays, there is the Advanced
Programming. This mode is only advisable for advanced users.

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 5 of 16
3Control of the thermostat.
Normally the displays show the measured humidity and the selected setpoint.
Switching the thermostat on and off.
With the ON/OFF key the MC 795D can be switched on and off. Is the hygrostat switched off, all
displays are off. No control function is active.
Select and change humidity setpoint.
With the UP and DOWN keys the desired setpoint can be selected. The LED's next to the
setpoint display indicate which setpoint is shown.
By pushing the SETPOINT key, the setpoint starts flashing. With the UP and DOWN keys the
setpoint can be changed. By pressing the SETPOINT key again, the new setpoint is accepted.
Read-out and switching sensors on and off.
By pressing the SENS key the humidity of the first sensor is shown in the upper display.
The lower display shows the number of the sensor and of the sensor is switched on or off. 'S1on'
means that the humidityof sensor 1 is shown and that the sensor is switched on.
Sensors that are switched on are used for the control, switched off sensors not. If more sensors
for a hygrostat are switched on, the control is based on the average of those sensors.
If during the read-out of a sensor is pressed on the SETP key, a sensor can be switched on or
switched off.
By pressing the SENS key once again, the next sensor is shown. After all sensors are shown,
the average measured humidity and the setpoint are shown in the display.
Reset the alarm.
As soon as an alarm situation occurs and an error message appears on the display can, by
pressing the RESET ALARM key, the alarm be reset.
The error message remains in the display, until the cause of the error is solved.
Day/night input.
If the NIGHT input is closed, the MC 795D turns to the night mode. The NIGHT LED will light.
The setpoints are increased with the night offset.
External alarm input.
If the external alarm input is closed, an alarm message “FE” appears in the display. The alarm
relay is activated. By pressing the RESET ALARM key, the alarm be reset. The error message
remains in the display, until the cause of the error is solved.

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 6 of 16
4Programming internal settings.
By pressing the RESET ALARM and SENS key simultaneously for more than 5 seconds, the Internal
Parameter menu is entered. The humidity display shows a P with a number. With the UP and DOWN
keythe desired parameter can be selected.
The setpoint display shows the value of the parameter. By pressing the SETPOINT key simultaneously
with the UP or DOWN key, the value can be adjusted.
The parameter table shows the normal programming functions of the hygrostat. It is possible to make
other combinations between sensors, setpoints and relays. For these advanced programming function
please see chapter 8 'Advanced Programming'.
If during 30 seconds no key is touched, the display returns to the normal operating mode.
Parameter table.
Number Description Range Value Default
Function of the hygrostat
P 01 Function hygrostat
0 = 1 setp, 1 relay (D)
1 = 1 setp, 2 relay (D21)
2 = 2 setp, 2 relay (D22)
3 = 1 setp, 3 relay (D31)
4 = 3 setp, 3 relay (D33)
5 = 1 setp, 4 relay (D41)
6 = 4 setp, 4 relay (D44)
0..6 - 0
Settings of the sensors
P 11
P 12
P 13
P 14
P 15
P 16
P 17
P 18
Sensor 1
0 = absent
1 = present
Sensor 2
Sensor 3
Sensor 4
Offset humidity sensor 1
Offset humidity sensor 2
Offset humidity sensor 3
Offset humidity sensor 4
0..1
0..1
0..1
0..1
-10..+10
-10..+10
-10..+10
-10..+10
-
-
-
-
% RH
% RH
% RH
% RH
0
0
0
0
0.0
0.0
0.0
0.0
Setting of the relays
P 21
P 22
P 23
P 24
P 25
P 26
P 27
P 28
P 29
P 30
P 31
P 32
Function relay 2
0 = dehumdifying
1 = humdifying
Differential relay 2
Offset relay 2
Function relay 3
Differential relay 3
Offset relay 3
Function relay 4
Differential relay 4
Offset relay 4
Function relay 5
Differential relay 5
Offset relay 5
0..1
0.1..15.0
-15..+15
0..1
0.1..15.0
-15..+15
0..1
0.1..15.0
-15..+15
0..1
0.1..15.0
-15..+15
-
% RH
% RH
-
% RH
% RH
-
% RH
% RH
-
% RH
% RH
0
0.5
0.0
0
0.5
0.0
0
0.5
0.0
0
0.5
0.0

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 7 of 16
Number Description Range Value Default
Setting of the alarm
P 41
P 42
P 43
P 44
P 45
P 46
P 47
P 48
P 49
Type humidity alarm
0 = No alarm
1 = Absolute alarm
2 = Relative to setpoint
Minimum alarm value
Maximum alarm value
Minimum alarm delay
Maximum alarm delay
Humidity control off
during minimum alarm
Humidity control off
during minimum alarm
Humidity control off
if all sensors at fault
Control off during external alarm
0..2
-100..+100
0..+100
0..99
0..99
0 = no
1 = yes
0 = no
1 = yes
0 = no
1 = yes
0 = no
1 = yes
-
% RH
% RH
minutes
minutes
-
-
-
-
1
0.0
+100.0
0
0
0
0
0
0
Display and setpoint
P 51
P 52
P 53
P 55
Minimum setpoint value
Maximum setpoint value
Read-out per 0,1% RH
Offset night shift
0.0..+100.0
0.0..+100.0
0 = no
1 = yes
-15..+15
% RH
% RH
-
% RH
0.0
+100.0
0
0.0
Setting analog outputs
P 61
P 62
P 63
P 64
P 65
P 66
P 71
P 72
P 73
P 74
P 75
P 76
Function analog output 1
0 = Average control temp.
1 = Setpoint
2 = P(I) dehumidifying
3 = P(I) humidifying
0 V out at
10 V out at
Proportional band
Offset prop. band
Intergral value
(999 gives only P)
Function analog output 2
0 = Average control temp.
1 = Setpoint
2 = P(I) dehumidifying
3 = P(I) humidifying
0 V out at
10 V out at
Proportional band
Offset prop. band
Intergral value
(999 gives only P)
0..3
-100..+100
-100..+100
0.1..15
-15..+15
1..999
0..3
-100..+100
-100..+100
0.1..15
-15..+15
1..999
-
-
-
-
-
minutes
-
-
-
-
-
minutes
0
0.0
+100.0
1.0
0.0
999
0
0.0
+100.0
1.0
0.0
999
Production details
P 91
P 92
P 93
Software version number
Serial number
Production date
-
-
-
-
-
year/wk
-
-
-

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 8 of 16
5Operation relay outputs.
Function selection of the hygrostat.
With parameter P 01 the function of the hygrostat is selected.
0 (D) = 1-stage hygrostat with one setpoint and one relay output.
1 (D21) = 2-stage hygrostat with one setpoint and two relay outputs.
2 (D22) = 2 hygrostats each with his own setpoint and relay output.
3 (D31) = 3-stage hygrostat with one setpoint and two relay outputs.
4 (D33) = 3 hygrostats each with his own setpoint and relay output.
5 (D41) = 4-stage hygrostat with one setpoint and two relay outputs.
6 (D44) = 4 hygrostats each with his own setpoint and relay output.
All these hygrostats control on the average humidity off the active sensors.
Operation of the dehumidifying or humidifying.
For each relay the function dehumidifying or humidifying can be programmed.
The dehumidifying switches on if the humidity is higher than the setpoint + offset
dehumidifying + differential dehumidifying and switches off if the humidity is below setpoint
+ offset dehumidifying.
The heating switches on if the humidity is lower than the setpoint + offset humdifying -
differential humdidifying and switches off if the humidity is above setpoint + offset
humidifying.
Operation of the alarm.
A selection can be made between no alarm, absolute alarm and relative alarm (P 41).
At an absolute alarm an alarm message will follow as soon as one of the active sensor exceeds
the alarm levels. The time delay prevents that an alarm will follow if e.h. the door of the cold
room is opened shortly.
The relative alarm are linked to the setpoint. A relative maximum alarm follows if one of the
active sensors has a humidity which is higher than setpoint + maximum alarm value, taking
the time delay into account. A relative minimum alarm follows if one of the active sensors has a
humidity which is lower than setpoint - minimum alarm value, taking the time delay into
account.
Display and setpoint.
The range over which the setpoint can be set, can be limited with parameter P 51 and P52.
Also a read-out per 0,1% RH or per 1% RH can be selected.

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 9 of 16
6Sensor calibration.
With the parameters P15 to P18 the humidity sensors can be calibrated. Indicates humidity sensor 1
e.g. 2% Rh too much, the offset (P 15) should be set at -2% RH.
7Alarms.
In normal position the alarm relay is on and drops during alarm. This to give an alarm if there is a
power failure. During alarm the alarm LED on the front flashes. Depending on the settings of the
Internal Parameters the control will stop or continue.
An alarm can be caused by:
Humidity alarm : rLO = Minimum alarm humidity
rHI = Maximum alarm humidity
External alarm : FE = External alarm
Sensor failure : F1 = No Humidity sensor on Hygrostat-1
F2 = No Humidity sensor on Hygrostat-2
F3 = No Humidity sensor on Hygrostat-3
F4 = No Humidity sensor on Hygrostat-4
E1 = Humidity sensor 1 broken
E2 = Humidity sensor 2 broken
E3 = Humidity sensor 3 broken
E4 = Humidity sensor 4 broken
EA = All control sensors at fault
By pressing the RESET ALARM key, the alarm relay is reset. The error message will remain in the
display until the alarm is solved. Also the alarm LED will remain flashing.

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 10 of 16
8Advanced Programming.
By pressing the SETP. and SENS key simultaneously for more than 5 seconds, the Advanced
Parameter menu is entered. The humidity display shows an A with a number. With the UP and DOWN
keythe desired parameter can be selected. At first A001 must be set to 1 to make the Advanced
Programming active.
Now all A... parameters can be set. All P... parameters are not active, they can’t be looked at or
changed (Only as A001 =0 the P.. Parameters can be set or shown again).
The setpoint display shows the value of the parameter. By pressing the SETPOINT key simultaneously
with the UP and DOWN key, the value can be adjusted.
If during 30 seconds no key is touched, the display returns to the normal operating mode.
Unless stated else, 0 = NO and 1 = YES.
Parameter table.
Number Description Range Value Default
General
A 001
A 002
A 003
A 004
Advanced programming active
Software version number
Serial number
Production date
0..1
-
-
-
-
-
-
year/wk
0
-
-
Number of hygrostats
A 010
A 011
A 012
Number of hygrostats
Hygrostat 1 is used as
differential hygrostat
Hygrostat 2 is used as
differential hygrostat
1..4
0..1
0..1
-
-
-
1
0
0
Sensor assignment
A 110
A 120
A 130
A 140
Sensor 1
0 = not present
1 = hygrostat 1
2 = hygrostat 2
3 = hygrostat 3
4 = hygrostat 4
5 = hygrostat 1 & 2
6 = hygrostat 1 & 3
7 = hygrostat 1 & 4
8 = hygrostat 2 & 3
9 = hygrostat 2 & 4
10 = hygrostat 3 & 4
11 = hygrostat 1, 2 & 3
12 = hygrostat 1, 2 & 4
13 = hygrostat 1, 3 & 4
14 = hygrostat 2, 3 & 4
15 = hygrostat 1, 2, 3 & 4
Sensor 2
Sensor 3
Sensor 4
0..15
0..15
0..15
0..15
-
-
-
-
1
1
1
1
When Hygrostat 1 is used as differential hygrostat it controls on the differential humidity of
sensor 1 minus sensor 2.
When Hygrostat 2 is used as differential hygrostat it controls on the differential humidity of
sensor 3 minus sensor 4.
The sensor has to be assigned accordantly.

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 11 of 16
Number Description Range Value Default
Sensor offset
A 210
A 220
A 230
A 240
Offset humidity sensor 1
Offset humidity sensor 2
Offset humidity sensor 3
Offset humidity sensor 4
-10..+10
-10..+10
-10..+10
-10..+10
% RH
% RH
% RH
% RH
0.0
0.0
0.0
0.0
Relay assignment
A 310
A 320
A 330
A 340
Relay 2
0 = not assigned
1 = hygrostat 1
2 = hygrostat 2
3 = hygrostat 3
4 = hygrostat 4
5 = hygrostat 1 & 2
6 = hygrostat 1 & 3
7 = hygrostat 1 & 4
8 = hygrostat 2 & 3
9 = hygrostat 2 & 4
10 = hygrostat 3 & 4
11 = hygrostat 1, 2 & 3
12 = hygrostat 1, 2 & 4
13 = hygrostat 1, 3 & 4
14 = hygrostat 2, 3 & 4
15 = hygrostat 1, 2, 3 & 4
Relay 3
Relay 4
Relay 5
0..15
0..15
0..15
0..15
-
-
-
-
1
1
1
1
Function of hygrostats
A 410
A 420
A 430
A 440
A 510
A 511
A 520
A 521
A 530
A 531
A 540
A 541
Function hygrostat 1
0 = dehumidifying
1 = humidifying
Function hygrostat 2
Function hygrostat 3
Function hygrostat 4
Differential hygrostat 1
Offset hygrostat 1
Differential hygrostat 2
Offset hygrostat 2
Differential hygrostat 3
Offset hygrostat 3
Differential hygrostat 4
Offset hygrostat 4
0..1
0..1
0..1
0..1
0.1..15.0
-15..+15
0.1..15.0
-15..+15
0.1..15.0
-15..+15
0.1..15.0
-15..+15
-
-
-
-
% RH
% RH
% RH
% RH
% RH
% RH
% RH
% RH
0
0
0
0
0.5
0.0
0.5
0.0
0.5
0.0
0.5
0.0

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 12 of 16
Number Description Range Value Default
Setting of the alarms
A 610
A 611
A 612
A 613
A 614
A 615
A 616
A 620
A 621
A 622
A 623
A 624
A 625
A 626
A 630
A 631
A 632
A 633
A 634
A 635
A 636
A 640
A 641
A 642
A 643
A 644
A 645
A 646
A 650
A 651
Alarm setting hygrostat 1
0 = No alarm
1 = Absolute alarm
2 = Relative alarm
Minimum alarm value
Maximum alarm value
Minimum alarm delay
Maximum alarm delay
Control off at minimum alarm
Control off at maximum alarm
Alarm setting hygrostat 2
Minimum alarm value
Maximum alarm value
Minimum alarm delay
Maximum alarm delay
Control off at minimum alarm
Control off at maximum alarm
Alarm setting hygrostat 3
Minimum alarm value
Maximum alarm value
Minimum alarm delay
Maximum alarm delay
Control off at minimum alarm
Control off at maximum alarm
Alarm setting hygrostat 4
Minimum alarm value
Maximum alarm value
Minimum alarm delay
Maximum alarm delay
Control off at minimum alarm
Control off at maximum alarm
Humidity control off if all
control sensors at fault
Humidity control off at
external alarm
0..2
-100..+100
0..+100
0..99
0..99
0..1
0..1
0..2
-100..+100
0..+100
0..99
0..99
0..1
0..1
0..2
-100..+100
0..+100
0..99
0..99
0..1
0..1
0..2
-100..+100
0..+100
0..99
0..99
0..1
0..1
0..1
0..1
-
% RH
% RH
minutes
minutes
-
-
-
% RH
% RH
minutes
minutes
-
-
-
% RH
% RH
minutes
minutes
-
-
-
% RH
% RH
minutes
minutes
-
-
0
0.0
+100.0
0
0
0
0
0
0.0
+100.0
0
0
0
0
0
0.0
+100.0
0
0
0
0
0
0.0
+100.0
0
0
0
0
0
0
Display and setpoint
A 710
A 711
A 712
A 713
A 720
A 721
A 722
A 723
Minimum setpoint hygrostat 1
Maximum setpoint hygrostat 1
Read-out per 0,1% RH
Offset night mode hygrostat 1
Minimum setpoint hygrostat 2
Maximum setpoint hygrostat 2
Read-out per 0,1% RH
Offset night mode hygrostat 2
0..+100
0..+100
0..1
-15..+15
0..+100
0..+100
0..1
-15..+15
% RH
% RH
-
% RH
% RH
% RH
-
% RH
0.0
+100.0
0
0.0
0.0
+100.0
0
0.0
A 730
A 731
A 732
A 733
A 740
A 741
A 742
A 743
Minimum setpoint hygrostat 3
Maximum setpoint hygrostat 3
Read-out per 0,1% RH
Offset night mode hygrostat 3
Minimum setpoint hygrostat 4
Maximum setpoint hygrostat 4
Read-out per 0,1% RH
Offset night mode hygrostat 4
0..+100
0..+100
0..1
-15..+15
0..+100
0..+100
0..1
-15..+15
% RH
% RH
-
% RH
% RH
% RH
-
% RH
0.0
+100.0
0
0.0
0.0
+100.0
0
0.0

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 13 of 16
Number Description Range Value Default
Analog output 1
A 810
A 811
A 812
A 813
A 814
A 815
A 816
Function analog output 1
0 = Control temp. hygrostat 1
1 = Control temp. hygrostat 2
2 = Control temp. hygrostat 3
3 = Control temp. hygrostat 4
4 = Setpoint hygrostat 1
5 = Setpoint hygrostat 2
6 = Setpoint hygrostat 3
7 = Setpoint hygrostat 4
8 = Humidity sensor 1
9 = Humidity sensor 2
10 = Humidity sensor 3
11 = Humidity sensor 4
12 = P(ID) dehumidifing hygrostat 1
13 = P(ID) dehumidifing hygrostat 2
14 = P(ID) dehumidifing hygrostat 3
15 = P(ID) dehumidifing hygrostat 4
16 = P(ID) humidifing hygrostat 1
17 = P(ID) humidifing hygrostat 2
18 = P(ID) humidifing hygrostat 3
19 = P(ID) humidifing hygrostat 4
0 V out at
10 V out at
Proportional band
Offset proportional band
Integral value (999 = P)
Differential value
0..19
-100..+100
-100..+100
0.1..15
-15..+15
1..999
0..999
-
-
-
-
-
minutes
minutes
0
0.0
+100.0
1.0
0.0
999
0
Analog output 2
A 820
A 821
A 822
A 823
A 824
A 825
A 826
Function analog output 2
0 = Control temp. hygrostat 1
1 = Control temp. hygrostat 2
2 = Control temp. hygrostat 3
3 = Control temp. hygrostat 4
4 = Setpoint hygrostat 1
5 = Setpoint hygrostat 2
6 = Setpoint hygrostat 3
7 = Setpoint hygrostat 4
8 = Humidity sensor 1
9 = Humidity sensor 2
10 = Humidity sensor 3
11 = Humidity sensor 4
12 = P(ID) dehumidifing hygrostat 1
13 = P(ID) dehumidifing hygrostat 2
14 = P(ID) dehumidifing hygrostat 3
15 = P(ID) dehumidifing hygrostat 4
16 = P(ID) humidifing hygrostat 1
17 = P(ID) humidifing hygrostat 2
18 = P(ID) humidifing hygrostat 3
19 = P(ID) humidifing hygrostat 4
0 V out at
10 V out at
Proportional band
Offset proportional band
Integral value (999 = P)
Differential value
0..19
-100..+100
-100..+100
0.1..15
-15..+15
1..999
0..999
-
-
-
-
-
minutes
minutes
0
0.0
+100.0
1.0
0.0
999
0

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 14 of 16
9 Front views.
Front view MC 795D wall mount drawing 981714
Front view MC 795D panel mount drawing 981700

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 15 of 16
10 Connection diagrams.
Connection diagram MC 795D wall mount drawing 981715

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 16 of 16
Connection diagram MC 795D panel mount drawing 981702

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 17 of 16
11 Dimensions.
Dimensions wall mount drawing 940024

Operation Manual Document nr. : 053682 Version : V1.1
MC 795D Client : General Page : 18 of 16
Dimensions Panel mount drawing 961271
-.-.-.-.-.-.-.-.-.
@