Ventev VenVolt2 802.3af User manual

PRODUCT SPECIFICATIONS:
• Ports:
• USB-C (In/ Out)
• USB-A (Out)
• 24V PoE (Out)
• LAN (In)
• PoE++ 802. af/at/b (Out) LAN (RJ45 Gigabit)
• PoE Output: 802. af/at/bt 24V Gigabit PoE
• USB-A Output: 5V/ A,9V/2A,12V/1.5A 18W (max.)
• LED: Battery Indicator Light (100%, 75%, 50%, 25%) USB-C
(Input/ Output)
• USB-C Input: 5V/ A, 9V/ A, 12V/ A, 15V/ A, 20V/ A
• USB-C Output: 5V/ A, 9V/ A, 12V/ A, 15V/ A, 20V/ A, PPS
. - 21V/ A
• Battery Type: Lithium Polymer Battery
• Battery Capacity: 26400mAh/ 98Wh Recharging Time: Hrs
VenVolt2 802.3af/at/bt
26 00 mAh Power Bank User Manual
www.ventev.com/infra [email protected] 800.851. 965

VenVolt2 802.3af/at/bt
26 00 mAh Power Bank User Manual
www.ventev.com/infra [email protected] 800.851. 965
APPLICATION
Output USB-C 48V PoE+Data
24V PoE+Data
Access
Point
Access
Point

VenVolt2 802.3af/at/bt
26 00 mAh Power Bank User Manual
www.ventev.com/infra [email protected] 800.851. 965
• The RP-98BT Power Bank is the perfect accessory for any WISP technician or wireless engineer. Power your devices
with USB-A, USB-C, 24V PoE, and PoE++ (802. bt).
• Carry 26400 mAh of power with you up a tower to remotely power your devices.
• The RP-98BT Power Bank is temperature resistant and also features protection from various factors such as input
overvoltage, output overvoltage, short circuit, and incorrect insertion.
OVERVIEW
USER INSTRUCTIONS

VenVolt2 802.3af/at/bt
26 00 mAh Power Bank User Manual
www.ventev.com/infra [email protected] 800.851. 965
USER INSTRUCTIONS
Operating guide
Use provided USB-C wall charger and USB-C to USB-C cable to connect VenVolt to USB-C charger. Be sure to fully
charge your VenVolt before your first use. The battery is shipped between 25 and 50% due to regulation requirements.
Charging typically takes to 4 hours to fully charge
Charging device PoE Device
To power a PoE device use your own ethernet cable to connect from VenVolt to your device.
Move select switch from Off to 4 for PoE++ port
Move select switch from Off to for 24V PoE port
USB-C port is disabled if switch is set to or 4
Charging laptop or phone with USB-C port:
To power a USB device use included cable or your own cable
Move select switch to Off
Battery will automatically detect a device has been connected and charging will begin.
Charging a device via the USB-A port:
The USB-A port is on when select switch is set to or 4. When the select switch is set to OFF only the USB-C port is
active.
Safety Precautions
Do not expose the product to fire or other high-temperature environments. The recommended usage temperature is
between 14 degrees F to 11 degrees F.
Do not expose the product to water
Stop using is any of the following conditions occur: electrolytic liquid leakage, overheating, color change, or other
unusual conditions.
Do not short circuit the positive (+) and negative (-).
Maintenance
Do not expose the VenteVolt2 to direct sunlight for long periods of time, or leave it any place with high temperature or
high humidity.
Discharge and recharge the VenVolt2 periodically if you don’t plan to use it for an extended period of time.

VenVolt2 802.3af/at/bt
26 00 mAh Power Bank User Manual
www.ventev.com/infra [email protected] 800.851. 965
USER INSTRUCTIONS
FCC Part 15 Text
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. This Class B device complies with
Canadian ICES- (B)/NMB- (B). Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions,may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures. Reorient or relocate the receiving antenna. Increase the separation
between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Third line I would remove number in the middle column. Update number 5 at the end to add to make sure
selector switch is set to “USB-C” for USB-C port or switch is set to “ ” or “4” for USB-A port. Delete
number from corrective actions as well.
For the last line let’s change problem to The LED’s on the VenVolt are flashing. Change number 2 in
correct actions to: “remove cable if the cable is faulty, switch the selector button to a different setting and
then back to setting you want to use”
LED Battery Level Indicator

VenVolt2 802.3af/at/bt
26 00 mAh Power Bank User Manual
www.ventev.com/infra [email protected] 800.851. 965
TROUBLESHOOTING GUIDE
Problem Possible Causes Corrective Actions
The VenVolt2 cannot be fully
charged.
1. The charging time is not
enough.
2. The power source is defective
1. With no devices attached,
charge the VenVolt2 for min.
hours.
2. Contact Ventev customer
service.
The remaining power in the
VenVolt2 cannot be read. The capacity is fully depleted.
1. Recharge the VenVolt2.
2. Contact Ventev customer
service
The VenVolt2 fails to supply
power to devices.
1. The capacity is very low.
2. Poor connection between
components.
. The VenVolt2 may not charge
certain devices.
4. Check that the VenVolt2 is
turned on.
5. Make sure selector switch is
set to “USB-C” for USB-C port
or switch is set to “ ” or “4” for
USB-A port.
1. Recharge the VenVolt2
2. Reconnect or replace the
cable and/or connector.
. Contact Ventev customer
service.
The VenVolt2 goes into
alarm mode, all of the LED
lights are flashing.
Electrical protection has been
triggered.
1. Reconnect or replace the
cable and/or connector.
2. Press the on/off button to
reset.