Vents DVUT 300 HB User manual

DVUT/DVUE 300 HB/HBE/HBE2
DVUT 500 HB/HBE/HBE2
Single-room heat recovery air handling unit
USER’S MANUAL

2
DVUT/DVUE HB(E/E2) EC
www.ventilation-system.com
CONTENTS
Safety requirements..................................................................................................................................................................... 3
Purpose................................................................................................................................................................................................ 5
Delivery set........................................................................................................................................................................................ 5
Designation key ............................................................................................................................................................................ 5
Technical data.................................................................................................................................................................................. 6
Design and operating principle ........................................................................................................................................... 8
Mounting and set-up ................................................................................................................................................................ 10
Connection to power mains .................................................................................................................................................. 14
Technical maintenance.............................................................................................................................................................. 16
Troubleshooting............................................................................................................................................................................. 18
Storage and transportation regulations.......................................................................................................................... 18
Manufacturer’s warranty........................................................................................................................................................... 19
Certificate of acceptance.......................................................................................................................................................... 23
Seller information.......................................................................................................................................................................... 23
Installation certificate.................................................................................................................................................................. 23
Warranty card................................................................................................................................................................................... 23

3
www.ventilation-system.com
This user’s manual is a main operating document intended for technical, maintenance, and operating staff.
The manual contains information about purpose, technical details, operating principle, design, and installation of the
DVUT/DVUE HB(E/E2) EC unit and all its modifications.
Technical and maintenance staff must have theoretical and practical training in the field of ventilation systems and should be able to
work in accordance with workplace safety rules as well as construction norms and standards applicable in the territory of the country.
The information in this user’s manual is correct at the time of the document’s preparation.
The Company reserves the right to modify the technical characteristics, design, or configuration of its products at any time in order to
incorporate the latest technological developments.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means in any information
search system or translated into any language in any form without the prior written permission of the Company.
SAFETY REQUIREMENTS
• Please read the user’s manual carefully prior to installing and operating the unit.
• All user’s manual requirements as well as the provisions of all the applicable local and national
construction, electrical, and technical norms and standards must be observed when installing
and operating the unit.
• The warnings contained in the user’s manual must be considered most seriously since they
contain vital personal safety information.
• Failure to follow the rules and safety precautions noted in this user’s manual may result in an
injury or unit damage.
• After a careful reading of the manual, keep it for the entire service life of the unit.
• While transferring the unit control, the user’s manual must be turned over to the receiving
operator.
UNIT INSTALLATION AND OPERATION SAFETY PRECAUTIONS
• Disconnect the unit from power mains prior to any installation operations.
• Unpack the unit with care.
• The unit must be grounded!
• While installing the unit, follow the safety regulations specific to the use of electric tools.
• Do not change the power cable length at your own discretion.
• Do not bend the power cable.
• Avoid damaging the power cable.
• Do not put any foreign objects on the power cable.
• Do not lay the power cable of the unit in close proximity to heating equipment.
• Do not use damaged equipment or cables when connecting the unit to power mains.
• Do not operate the unit outside the temperature range stated in the user’s manual.
• Do not operate the unit in aggressive or explosive environments.
• Do not touch the unit controls with wet hands.
• Do not carry out the installation and maintenance operations with wet hands.
• Do not wash the unit with water.
• Protect the electric parts of the unit against ingress of water.
• Do not allow children to operate the unit.
• The unit is allowed to be used by children aged from 8 years oldand above and persons with
reduced physical, sensory, or mental capabilities or no experience and knowledge provided
that they have been given supervision or instruction regarding safe use of the unit and
understand the risks involved.

4
DVUT/DVUE HB(E/E2) EC
www.ventilation-system.com
THE PRODUCT MUST BE DISPOSED SEPARATELY AT THE END OF ITS SERVICE LIFE.
DO NOT DISPOSE THE UNIT AS UNSORTED DOMESTIC WASTE.
• Disconnect the unit from power mains prior to any technical maintenance.
• Do not store any explosive or highly flammable substances in close proximity to the unit.
• When the unit generates unusual sounds, odour, or emits smoke, disconnect it from power
supply and contact the Seller.
• Do not open the unit during operation.
• Do not direct the air flow produced by the unit towards open flame or ignition sources.
• Do not block the air duct when the unit is switched on.
• In case of continuous operation of the unit, periodically check the security of mounting.
• Do not sit on the unit and avoid placing foreign objects on it.
• Use the unit only for its intended purpose.

5
www.ventilation-system.com
DELIVERY SET
DESIGNATION KEY
THE UNIT SHOULD NOT BE OPERATED BY CHILDREN OR PERSONS WITH REDUCED
PHYSICAL, MENTAL, OR SENSORY CAPACITIES, OR THOSE WITHOUT THE APPROPRIATE
TRAINING.
THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY QUALIFIED
PERSONNEL AFTER THE APPROPRIATE BRIEFING.
THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORIZED
ACCESS BY UNATTENDED CHILDREN.
NAME NUMBER
Air handling unit 1
User’s manual 1
Control panel (A14/A22/A25) 1
Key to a service panel 1
Packing box 1
DVUT 500 H B E DN EC Ax -1
Control panel location
__ : remote control panel
1: built-in control panel
Control
A14/A21/A22/A25
Motor type
EC: electronically commutated motors
Drain pump
_ : no drain pump
DN: integrated drain pump
Electric heaters
_ : no electric heater
E: integrated preheater
E2: integrated pre- and reheater
Bypass air damper
B: bypass damper included
Mounting features
H: floor mounting, horizontal spigots
Rated air capacity [m3/h]
Ventilation unit series
DVUT: single-room heat recovery ventilation unit
DVUE: single-room energy recovery ventilation unit
PURPOSE
The unit is designed to ensure continuous mechanical air exchange in houses, offices, hotels, cafes, conference halls, and other utility
and public spaces as well as to recover the heat energy contained in the air extracted from the premises to warm up the filtered stream
of intake air.
The unit is not intended for organizing ventilation in swimming pools, saunas, greenhouses, summer gardens, and other spaces with
high humidity.
Due to the ability to save heating energy by means of energy recovery, the unit is an important element of energy-efficient premises.
The unit is a component part and is not designed for stand-alone operation. It is rated for continuous operation.
Transported air must not contain any flammable or explosive mixtures, evaporation of chemicals, sticky substances, fibrous materials,
coarse dust, soot and oil particles or environments favourable for the formation of hazardous substances (toxic substances, dust,
pathogenic germs).

6
DVUT/DVUE HB(E/E2) EC
www.ventilation-system.com
UNIT OVERALL DIMENSIONS MM
W
H +20* A
W2 W1 W2
View А
H1
H2 +20*
L
D
L1
Model D W W1 W2 L L1 H H1 H2
DVUT 300 HB (E/E2) EC 200 620 230 195 470 520 1770 1476 294
DVUE 300 HB (E/E2) EC
DVUT 500 HB (E/E2) EC 250 750 290 230 535 585 2170 1833 337
* The unit height may be adjusted by means of levelling feet.
TECHNICAL DATA
The unit is designed for application with the ambient temperature ranging from +1 °C to +40 °C and relative humidity up to 80 %.
In order to prevent condensation on the internal walls of the unit, it is necessary that the surface temperature of the casing is 2-3 °C above
the dew point temperature of the transported air.
The unit is rated as a Class I electrical appliance.
Hazardous parts access and water ingress protection rating:
• IP22 for the unit connected to the air ducts
• IP44 for the unit motors
The unit design is constantly being improved, thus some models may be slightly different from those described in this manual.

7
www.ventilation-system.com
Model
DVUT 300 HB EC DVUT 300 HBE EC DVUT 300 HBE2 EC DVUE 300 HB EC DVUE 300 HBE EC DVUE 300 HBE2 EC DVUT 500 HB EC DVUT 500 HBE EC DVUT 500 HBE2 EC
Power supply voltage, 50 (60) Hz [V] 1~220-240
Unit power consumption excl. electric heater [W] 125 230
Preheater power consumption [W] - 1400 1400 - 1400 1400 - 1400 1400
Reheater power consumption [W] - - 1400 - - 1400 - - 2800
Maximum unit current excl. electric heater [A] 0.9 0.9 0.9 0.9 0.9 0.9 1.7 1.7 1.7
Maximum unit current incl. electric heater(s) [A] 0.9 7 13.1 0.9 7 13.1 1.7 7.8 20
Maximum air flow [m3/h] 320 320 320 320 320 320 580 580 580
Noise level, 1 m [dBA] 31 33
Noise level, 3 m [dBA] 21 23
Transported air temperature [˚C] -25...+40
Casing material painted steel
Insulation 40 mm mineral wool
Extract filter G4 x 2
Supply filter G4 + F8
Optional supply filter: material/size/filtration rate H11+ F8
Connected duct diameter [mm] 200 200 250
Weight [kg] 138±3% 139±3% 140±3% 136±3% 137±3% 138±3% 191±3% 193±3% 194±3%
Heat recovery efficiency [%] 78-92 73-89 75-94
Heat exchanger type counter-flow
Heat exchanger material polystyrene enthalpy polystyrene
SEC class A

8
DVUT/DVUE HB(E/E2) EC
www.ventilation-system.com
DESIGN AND OPERATING PRINCIPLE
The unit operation is as follows:
Warm extract air from the room flows into the unit and is cleaned in
the extract filters. Then the air is moved through the heat exchanger
and is exhausted outside through the air ducts with the extract fan.
Cold fresh air from outside flows into the unit, where it is cleaned with
the supply filters. Then the air flows through the heat exchanger and
is moved to the room with the supply fan. Supply air is heated in the
heat exchanger by transferring the heat energy of warm and humid
extract air to the cold fresh air. The air flows are fully separated while
flowing through the heat exchanger. Heat recovery minimizes heat
losses, which reduces the cost of space heating in the cold season.
The unit is a frame structure made of rigidly fixed steel panels. The
panels are made of painted steel sheets and a galvanized steel sheets
with a layer of mineral wool between for heat- and sound-insulation.
UNIT DESIGN
UNIT OPERATING PRINCIPLE
Supply filter
Extract filter
Control unit
Temperature sensor
Electric reheater
Heat exchanger
Bypass air damper actuator
Supply fan
Supply filter
Supply air damper
Extract fan
Electric preheater
Exhaust air damper
Extract air
Exhaust air
Intake air
Extract air
Supply air
The service door enables access for maintenance and service
operations.
The power cables and grounding conductors must be routed
through the cable glands to the terminal block located on the top
casing panel. The wiring diagram for wiring of the air handling unit
is shown on the inner side of the terminal box lid. The unit design
enables installation of a bypass duct with a bypass damper to route
the intake air stream without contacting the heat exchanger. The
unit has three automatic heat exchanger freeze protection modes,
depending on the unit model.
Units without heater: the supply fan turns off in case of a freezing
danger*.
Units with a reheater and no preheater: the bypass system is
activated in case of a freezing danger*.
Units with a preheater: the preheating is turned on in case of a
freezing danger*.
* danger of freezing appears when the exhaust air temperature
downstream of the heat exchanger is lower than +5 °C and intake
air temperature upstream of the heat exchanger is lower than -3 °C.
After increase of these temperatures the unit reverts to the
previous operation mode.
The supply and extract air temperature difference during heat
recovery may lead to condensate formation in the units with a
polystyrene heat exchanger. The condensate is collected in the drain
pan and is removed outside to the exhaust air duct through the drain
hose. No condensate is generated in the units with an enthalpy heat
exchanger as the air moisture is transferred from one air stream to
the other via the membrane.
The unit has options for connection of a humidity sensor, CO2sensor
or VOC (air quality) sensor for automatic keeping of set humidity
level, CO2or VOC concentration in the room.
SETUP MODE
button
(for units with
A21/A22/A25
automation)

9
www.ventilation-system.com
Additional equipment (is not included in the delivery set, can be ordered separately)
• Humidity sensor. The unit with the installed humidity sensor maintains a set indoor humidity point. As the extract air humidity rises
above the set point, the system automatically switches to the maximum speed. As the humidity drops down below the set point the
unit returns to the previous mode
• CO2sensor. Measures the level of concentration of carbon dioxide in the room and generates a signal that controls the performance
of the fan. Air capacity control based on CO2concentration is an efficient energy saving solution.
• VOC sensor. Qualitative assessment of air saturation with contaminants (cigarette smoke, exhaled air, solvent and detergent vapours).
The sensor sensitivity can be adjusted with regards to the expected maximum level of air pollution. Enables on-demand ventilation
which results in considerable energy savings as air is exchanged only upon reaching the preset level of pollution.

10
DVUT/DVUE HB(E/E2) EC
www.ventilation-system.com
MOUNTING AND SETUP
READ THE USER'S MANUAL BEFORE INSTALLING THE UNIT.
Sufficient service access to the unit for maintenance or repair operations must be provided.
The recommended minimum distances from the unit to the walls are shown below.
Make sure the unit has no foreign objects inside before starting it up.
The unit is designed for mounting to a horizontal surface adjacent to the wall with the ready-made holes for the air ducts. The fixing
brackets with a fastening hole enable fixation of the unit to the wall. The fixing brackets are not included in the delivery set.
min 3°
Ø D
min Amin Bmin B
290
329+20*
Condensate drain pipe
U-trap (hydraulic lock) Sewage system
min 100 mm
min 50 mm
min 3°
Pipe
MODEL A mm B mm D mm
DVUT 300 HB(E/E2) EC 600 350 225
DVUE 300 HB(E/E2) EC
DVUT 500 HB(E/E2) EC 800 350 275
* the dimension may be increased during adjustment of the unit
by means of the levelling feet
The levelling feet on the bottom of the unit ensure exact alignment
of the unit during mounting.
For alignment of the unit loosen the nuts and adjust position of the
support disc manually using a wrench. Then tighten the upper and
the lower nut.
To attain the best performance of the unit and to minimise
turbulence-induced air pressure losses, while mounting connect
straight air duct sections to the unit spigots.
Minimum straight air duct length:
• equal to 1 air duct diameter on intake side
• equal to 3 air duct diameters on outlet side
If the air ducts are too short or not connected at any unit spigot,
protect the unit inner parts from ingress of foreign objects by installing a protecting grille or other protecting device with mesh side
width not more than 12.5 mm to prevent uncontrollable access to the fans.
Fasteners for the unit mounting are not included into delivery set and should be ordered separately.
While selecting appropriate fasteners consider material of the mounting surface as well as the weigh of the unit, refer to the technical
data. For selection of the fasteners for unit mounting please refer to a service technician.

11
www.ventilation-system.com
The drain pan in the heat recovery section is equipped with a drain pipe for condensate removal.
Connect the pipe, the U-trap or U-trap of the other type (hydraulic lock) that is not included in the delivery set and a sewage system with
metal, plastic or rubber connecting hoses. While laying the connection pipes provide the slope of minimum 3° downwards.
Before starting operation of the unit make sure that the water flows freely into the sewage collection system, otherwise condensed water
may build up in the unit during the heat exchanger operation which, in turn, may cause equipment failure and water ingress into the
premises. Fill up the U-trap with water before using it. When using other U-trap systems read the installation instruction to prepare the
condensate drain system for operation.
For the units with a drain pump make sure that the flexible hose from the pump must is connected to the sewage system.
The drain pump provides timely pumping of the condensed water from the unit.
to sewage system
THE CONDENSATE DRAIN SYSTEM IS DESIGNED FOR USE IN PREMISES WITH AMBIENT
TEMPERATURE ABOVE 0 °C!
IF THE EXPECTED AIR TEMPERATURES ARE BELOW 0 °C, THE CONDENSATE DRAINAGE
SYSTEM MUST BE EQUIPPED WITH HEAT INSULATION AND PREHEATING FACILITIES.

12
DVUT/DVUE HB(E/E2) EC
www.ventilation-system.com
MOUNTING OF SENSORS FOR UNITS WITH A14 AUTOMATION NOT INCLUDED IN THE DELIVERY SET
The humidity sensor must be attached inside of the extract air duct.
Attach the sensor to the insert. Open the unit, remove the upper part of the protective casing and install the insert with the sensor on
the bracket located on the wall of the exhaust duct. Connect the sensor connector to the connector with the cable from the control unit
(installed by the manufacturer).
After connecting the humidity sensor, it is necessary to change the control configuration in the controller. Contact the product Seller for
doing that.
The CO2sensor must be installed in the exhaust air duct upstream of the heat exchanger. Open the unit, remove the upper part of the
protective cover. Using a screwdriver remove the screw on the bracket holding the insert. Then use a small screwdriver to disconnect
the connector. Disassemble the CO2sensor in accordance with the instructions supplied with it and connect it in accordance with the
provided diagram. Reassemble the sensor in the reverse order and install it on the bracket inside the unit.
Update the control configuration after connection of the humidity sensor. Contact the product Seller for doing that.
1
3
2
CO2sensor connection
+U 24 V AC / DC
GND
0-10 VDC
From the unit
controller

13
www.ventilation-system.com
MOUNTING OF SENSORS FOR UNITS WITH A21 AUTOMATION NOT INCLUDED IN THE DELIVERY SET
Brackets for installing humidity, CO2and VOC sensors are located on the wall of the exhaust duct upstream of the heat exchanger.
12
The bracket 1 is designed for installing a humidity sensor or VOC sensor. The bracket 2 is designed for installing a humidity sensor or CO2
sensor.
To install the humidity sensor on the bracket 2, remove the insert by unscrewing the screw on the bracket.
Screw the humidity sensor to the desired bracket and connect the sensor connector to the cable connector from the control unit
(installed by the manufacturer).
To install the CO2/VOC sensor, disassemble the sensor in accordance with the instructions supplied with it. To install the CO2sensor,
remove the insert by unscrewing the screw on the bracket.
Connect the sensor to the controller in accordance with the diagram in the User’s manual for the control system.
Reassemble the sensor in the reverse order and fasten it to the bracket.

14
DVUT/DVUE HB(E/E2) EC
www.ventilation-system.com
CONNECTION TO POWER MAINS
POWER OFF THE POWER SUPPLY PRIOR TO ANY OPERATIONS WITH THE UNIT.
THE UNIT MUST BE CONNECTED TO POWER SUPPLY BY A QUALIFIED ELECTRICIAN.
THE RATED ELECTRICAL PARAMETERS OF THE UNIT ARE GIVEN ON THE
MANUFACTURER’S LABEL.
ANY TAMPERING WITH THE INTERNAL CONNECTIONS IS PROHIBITED
AND WILL VOID THE WARRANTY.
DO NOT LAY THE CABLE IN CLOSE PROXIMITY TO THE CONTROL
PANEL CABLE!
WHILE ROUTING THE CONTROL PANEL CABLE DO NOT COIL THE
EXTRA LENGTH.
Route the cables to the control unit through the sealed cabled glands in the unit.
All the electric connections must be performed in compliance with external wiring diagram and wired through the terminal block X1
in the control unit. Extra control units may be optionally connected to the unit. Extra connected control units are not included in the
delivery set and must be ordered separately. Extra connections are shown in dotted lines in the wiring diagram.
The unit is rated for connection to 1~230 V/50 (60) Hz power mains. The unit must be
connected to power mains using insulated electric cables with a wire cross section of
at least 2.5 mm2and with a cable length of up to 50 m. The conductors’ cross section
value is indicative. The actual wire cross section selection must be based on the type
of wire, its maximum allowable heating, insulation, length and installation method.
The external power input must be equipped with an automatic circuit breaker built
into the stationary wiring to open the electric circuit in case of overload or short-
circuit. The circuit breaker installation place must provide quick access for emergency
shutdown of the unit.The trip current of the automatic circuit breaker must correspond
to the current consumption of the unit (refer to the technical data table).
To access the terminal block, unscrew the screws of the control unit cover and remove
it.

15
www.ventilation-system.com
EXTERNAL WIRING DIAGRAM FOR THE UNITS WITH A14 AUTOMATION
11 10 9 87654321
+U Rx Tx
brown yellow green white
Control
panel
GND
C NO PK PK PE N L
PE N L
QF
+U Rx Tx
GND
C NO PK PK PE N L
NO contact of the
external control unit
(RH/CO2/VOC sensor)
PK: fire alarm panel
min. current 1 A (remove
the jumper during connection)
Connection of the re alarm panel (PK) contact
While connecting the fire alarm panel contact remove the jumper between the terminals 4 and 5. In this case, the connection relies on
a normally closed dry contact. In case of fire, the normally closed dry contact opens the control circuit from the central fire alarm panel
and cuts off power supply to the unit.
Connecting of the external control unit contact, such as RH/CO2/VOC sensor (NO, C).
Connect the CO2sensor to the terminals 6 and 7. In this case, connection relies on a normally open dry contact. Once the contact is
closed, the unit starts to run with the maximum speed.
The cable for connection of the control panel to the air handling unit must be of 4x0.25 mm2type and have the maximum length 10 m.
EXTERNAL WIRING DIAGRAM FOR THE UNITS WITH A21 AUTOMATION
L1 N N PE PE 1 2 C NC C NO GND A B +24V C NO
1 2 1 2 3 4 5 6 7 8 9 10
X1 X2
12
PK1 *
12 12 12
Boost*
GND A B +24V
P1*
CCU*
L1 N N
Power input 230 VAC
brown
yellow
green
white
Designation Name Type Wire Note
PK1* Contact from a fire alarm panel NC 2 x 0.75 mm2remove jumper
CCU* Cooler control NO 2 x 0.75 mm23 A, 30 V DC/~250 AC
P1* External control panel 4 x 0.25 mm2
Boost* Boost mode contacts On/Off NO 2 x 0.75 mm2
*Not included in the delivery set.
Output parameters: terminals 9-10 – 3 A, 30 V DC/~250 V AC (dry contact).
— ELECTRIC SHOCK HAZARD!

16
DVUT/DVUE HB(E/E2) EC
www.ventilation-system.com
TECHNICAL MAINTENANCE
Maintenance operations of the unit are required 3-4 times per year. Maintenance includes general cleaning of the unit and the following
operations:
1. Filter maintenance.
Clogged filters increase air resistance in the system and reduce supply air volume.
Clean the filters as required, but not less than 3-4 times per year.
Upon elapsing of the set time for filter replacement a signal for filter replacement or cleaning is generated. In this case clean or replace
the filters and reset the operating hours.
The filter timer must be reset by a service engineer.
Filter cleaning with a vacuum cleaner is allowed.
After two consecutive cleanings the filters must be replaced.
For new filters of the type stated in the technical data, please contact to the unit Seller.
Steps for removal of the filters:
• Disconnect the unit from power supply.
• Open the service door using the key.
• Press slightly and pull the fixing latches to remove the supply filters.
• Pull the filters to remove. Install the filters in the reverse order.
2. Heat exchanger maintenance (once per year).
Press the xing latches
to release the supply lters
DISCONNECT THE UNIT FROM POWER SUPPLY BEFORE
ANY MAINTENANCE OPERATIONS!

17
www.ventilation-system.com
Some dust may accumulate on the heat exchanger even in case of regular maintenance of the filters. Regular cleaning of the heat
exchanger is required to maintain high heat recovery efficiency. To clean the heat exchanger, pull it out of the unit and clean it with
compressed air or a vacuum cleaner. After cleaning install the heat exchanger back in the unit.
Steps for removal of the heat exchanger:
• Disconnect the unit from power supply.
• Open the service door using the key.
• Remove the 6 screws that retain the upper protective housing and take it off.
• Loosen the hand screws to release the heat exchanger, then pull the heat exchanger to remove.
• After completion of maintenance install the heat exchanger in the reverse order.
3. Fan maintenance (once a year).
Even in case of regular maintenance of the filters, some dust may accumulate inside the fans and reduce the fan performance and supply
air flow. Clean the fans with a soft cloth, brush or compressed air.
Loosen the hand screws
on the heat exchanger that
retain the heat exchanger.
Do not use water, aggressive solvents or sharp objects as they may damage the impeller.
4. Maintenance of air intake devices (twice per year).
The supply grille may get clogged with leaves and other objects, which reduces the unit performance and supply air delivery. Check the
supply grille twice per year and clean it as required.
5. Air duct system maintenance (every 5 years).
Even regular fulfilling of all the maintenance operations described above may not completely prevent dust accumulation in the air ducts,
which reduces the unit performance. Duct maintenance means regular cleaning or replacement.
6. Control unit maintenance (as required).
The control unit is located inside of the unit casing. For accessing the control unit remove the fixing screws on the panel and remove the
control unit lid.

18
DVUT/DVUE HB(E/E2) EC
www.ventilation-system.com
STORAGE AND TRANSPORTATION REGULATIONS
• Store the unit in the manufacturer’s original packaging box in a dry closed ventilated premise with temperature range
from +5 ˚C to +40 ˚C and relative humidity up to 70 %.
• Storage environment must not contain aggressive vapors and chemical mixtures provoking corrosion, insulation, and sealing
deformation.
• Use suitable hoist machinery for handling and storage operations to prevent possible damage to the unit.
• Follow the handling requirements applicable for the particular type of cargo.
• The unit can be carried in the original packaging by any mode of transport provided proper protection against precipitation and
mechanical damage. The unit must be transported only in the working position.
• Avoid sharp blows, scratches, or rough handling during loading and unloading.
• Prior to the initial power-up after transportation at low temperatures, allow the unit to warm up at operating temperature for at least
3-4 hours.
TROUBLESHOOTING
TROUBLE POSSIBLE REASONS Troubleshooting
The fan(s) do(es) not get
started during activation of
the unit.
No power supply. Make sure the power supply line is connected correct.
Otherwise troubleshoot a connection error.
Motor or impeller clogging. Turn the unit off. Troubleshoot the fan clogging. Clean
the blades. Restart the unit.
System failure. Turn the unit off. Contact the product Seller.
Automatic circuit breaker
tripping after the unit start-
up.
Overcurrent as a result of short circuit in the
electric circuit. Turn the unit off. Contact the product Seller.
Low air flow.
Low set fan speed. Set higher speed.
Clogged filters, fans or heat exchanger. Clean or replace the filters. Clean the fans and the heat
exchanger.
Clogged or damaged air ducts, diffusers,
louver shutters, grilles or other ventilation
system components.
Clean or replace the air ducts, diffusers, louver shutters,
grilles or other ventilation system components.
Low supply air temperature. Clogged extract filter. Clean or replace the extract filter.
Noise, vibration.
The impeller(s) is soiled. Clean the impeller(s).
The fan or casing screw connection is loose. Tighten the screw connection of the fans or the casing
all the way.
No anti-vibration connectors on air duct
pipe flanges. Install anti-vibration connectors.
Water leakage for the
CIVIC EC LB(E/E2) 300 models. Drain lime is clogged, damaged or installed
incorrect.
Clean the drain line. Check the drain line slope. Make
sure that the U-trap is filled with water and that drain
hoses are frost protected.
The alarm indicator
glows on the control panel
(for the units with A14 control
panel).
Communication loss (cable or wire
breakdown) between the control panel and
the ventilation unit.
Check the power and connection cables and wires
between the control panel and the air handling
unit for integrity using a multimeter. If unassisted
troubleshooting fails, please contact the product Seller.
Wrong cable installation.
Make sure the cable installation is completed according
to the requirements stated in the user’s manual for the
control panel. Otherwise install the cable as required.
System failure. Contact the product Seller.

19
www.ventilation-system.com
MANUFACTURER’S WARRANTY
The product is in compliance with EU norms and standards on low voltage guidelines and electromagnetic compatibility. We hereby
declare that the product complies with the provisions of Electromagnetic Compatibility (EMC) Directive 2014/30/EU of the European
Parliament and of the Council, Low Voltage Directive (LVD) 2014/35/EU of the European Parliament and of the Council and CE-marking
Council Directive 93/68/EEC. This certificate is issued following test carried out on samples of the product referred to above.
The manufacturer hereby warrants normal operation of the unit for 24 months after the retail sale date provided the user's observance
of the transportation, storage, installation, and operation regulations. Should any malfunctions occur in the course of the unit operation
through the Manufacturer's fault during the guaranteed period of operation, the user is entitled to get all the faults eliminated by the
manufacturer by means of warranty repair at the factory free of charge. The warranty repair includes work specific to elimination of faults
in the unit operation to ensure its intended use by the user within the guaranteed period of operation. The faults are eliminated by means
of replacement or repair of the unit components or a specific part of such unit component.
The warranty repair does not include:
• routine technical maintenance
• unit installation/dismantling
• unit setup
To benefit from warranty repair, the user must provide the unit, the user's manual with the purchase date stamp, and the payment
paperwork certifying the purchase. The unit model must comply with the one stated in the user’s manual. Contact the Seller for warranty
service.
The manufacturer’s warranty does not apply to the following cases:
• User’s failure to submit the unit with the entire delivery package as stated in the user’s manual including submission with missing
component parts previously dismounted by the user.
• Mismatch of the unit model and the brand name with the information stated on the unit packaging and in the user's manual.
• User’s failure to ensure timely technical maintenance of the unit.
• External damage to the unit casing (excluding external modifications as required for installation) and internal components caused
by the user.
• Redesign or engineering changes to the unit.
• Replacement and use of any assemblies, parts and components not approved by the manufacturer.
• Unit misuse.
• Violation of the unit installation regulations by the user.
• Violation of the unit control regulations by the user.
• Unit connection to power mains with a voltage different from the one stated in the user's manual.
• Unit breakdown due to voltage surges in power mains.
• Discretionary repair of the unit by the user.
• Unit repair by any persons without the manufacturer’s authorization.
• Expiration of the unit warranty period.
• Violation of the unit transportation regulations by the user.
• Violation of the unit storage regulations by the user.
• Wrongful actions against the unit committed by third parties.
• Unit breakdown due to circumstances of insuperable force (fire, flood, earthquake, war, hostilities of any kind, blockades).
• Missing seals if provided by the user’s manual.
• Failure to submit the user’s manual with the unit purchase date stamp.
• Missing payment paperwork certifying the unit purchase.
FOLLOWING THE REGULATIONS STIPULATED HEREIN WILL ENSURE A LONG AND
TROUBLEFREE OPERATION OF THE UNIT.
USER’S WARRANTY CLAIMS SHALL BE SUBJECT TO REVIEW ONLY UPON
PRESENTATION OF THE UNIT, THE PAYMENT DOCUMENT AND THE USER’S MANUAL
WITH THE PURCHASE DATE STAMP.

20
DVUT/DVUE HB(E/E2) EC
www.ventilation-system.com