Vents VUT 160 PB EC User manual

VUT 160 PB EC
VUT 250 PB EC
VUT 350 PB EC
Heat recovery air handling unit
USER’S MANUAL

2
VUT 160/250/350 PB EC
www.ventilation-system.com
CONTENTS
Safety requirements..................................................................................................................................................................... 2
Purpose................................................................................................................................................................................................ 4
Delivery set........................................................................................................................................................................................ 4
Designation key.............................................................................................................................................................................. 4
Technical data.................................................................................................................................................................................. 5
Unit design and operating principle................................................................................................................................. 7
Installation and set-up................................................................................................................................................................ 10
Connection to power mains and unit control ............................................................................................................ 13
Technical maintenance.............................................................................................................................................................. 15
Storage and transportation regulations.......................................................................................................................... 16
Manufacturer’s warranty........................................................................................................................................................... 17
Certificate of acceptance.......................................................................................................................................................... 19
Seller information.......................................................................................................................................................................... 19
Installation certificate.................................................................................................................................................................. 19
Warranty card................................................................................................................................................................................... 19
This user’s manual is a main operating document intended for technical, maintenance, and operating staff.
Themanualcontains informationaboutpurpose, technicaldetails,operatingprinciple, design,and installation oftheVUT 160/250/350PBEC
unit and all its modifications.
Technical and maintenance staff must have theoretical and practical training in the field of ventilation systems and should be able to
work in accordance with workplace safety rules as well as construction norms and standards applicable in the territory of the country.
The information in this user’s manual is correct at the time of the document’s preparation.
The Company reserves the right to modify the technical characteristics, design, or configuration of its products at any time in order to
incorporate the latest technological developments.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means in any information
search system or translated into any language in any form without the prior written permission of the Company.

3
www.ventilation-system.com
UNIT INSTALLATION AND OPERATION SAFETY PRECAUTIONS
• Disconnect the unit from
power mains prior to any
installation operations.
• Unpack the unit with care.
• The unit must be grounded!
• While installing the unit, follow
the safety regulations specific
to the use of electric tools.
• Do not change the power
cable length at your own
discretion.
• Do not bend the power cable.
• Avoid damaging the power
cable.
• Do not put any foreign objects
on the power cable.
• Do not lay the power cable of
the unit in close proximity to
heating equipment.
• Do not use damaged
equipment or cables when
connecting the unit to power
mains.
• Do not operate the unit
outside the temperature range
stated in the user’s manual.
• Do not operate the unit
in aggressive or explosive
environments.
• Do not touch the unit controls
with wet hands.
• Do not carry out the
installation and maintenance
operations with wet hands.
• Do not wash the unit with
water.
• Protect the electric parts of the
unit against ingress of water.
SAFETY REQUIREMENTS
• Please read the user’s manual carefully prior to installing and operating the unit.
• All user’s manual requirements as well as the provisions of all the applicable local and national
construction, electrical, and technical norms and standards must be observed when installing
and operating the unit.
• The warnings contained in the user’s manual must be considered most seriously since they
contain vital personal safety information.
• Failure to follow the rules and safety precautions noted in this user’s manual may result in an
injury or unit damage.
• After a careful reading of the manual, keep it for the entire service life of the unit.
• While transferring the unit control, the user’s manual must be turned over to the receiving
operator.

4
VUT 160/250/350 PB EC
www.ventilation-system.com
• Do not allow children to
operate the unit.
• Disconnect the unit from
power mains prior to any
technical maintenance.
• Do not store any explosive or
highly flammable substances
in close proximity to the unit.
• When the unit generates
unusual sounds, odour, or
emits smoke, disconnect it
from power supply and contact
the Seller.
• Do not open the unit during
operation.
• Do not direct the air flow
produced by the unit towards
open flame or ignition sources.
• Do not block the air duct when
the unit is switched on.
• In case of continuous
operation of the unit,
periodically check the security
of mounting.
• Do not sit on the unit and
avoid placing foreign objects
on it.
• Use the unit only for its
intended purpose.
THE PRODUCT MUST BE DISPOSED SEPARATELY AT THE END OF ITS SERVICE LIFE.
DO NOT DISPOSE THE UNIT AS UNSORTED DOMESTIC WASTE.

5
www.ventilation-system.com
VUT X P B EC LA14
Control
A11/A14/A21
Service side
L - left service side
R - right service side
Motor type
EC – electronically commutated
Additional components
B – bypass
Spigot orientation
P – suspended mounting, horizontal spigot
orientation
Rated air ow [m3/h]
Unit type
VUT – heat recovery air handling unit
DESIGNATION KEY
Air handling unit 1 pc.
User's manual 1 pc.
Control panel (only for units with A11 and A14 automation) 1 pc.
Mounting box for wall flush mounting (only for units with A14 automation) 1 pc.
Mounting box for wall surface mounting (only for units with A14 automation) 1 pc.
Fastening kit 1 pc.
Packing box 1 pc.
PURPOSE
The unit is designed to ensure continuous mechanical air exchange in houses, offices, hotels, cafes, conference halls, and other utility
and public spaces as well as to recover the heat energy contained in the air extracted from the premises to warm up the filtered stream
of intake air.
The unit is not intended for organizing ventilation in swimming pools, saunas, greenhouses, summer gardens, and other spaces with
high humidity.
Due to the ability to save heating energy by means of energy recovery, the unit is an important element of energy-efficient premises.
The unit is a component part and is not designed for stand-alone operation.
It is rated for continuous operation.
Transported air must not contain any flammable or explosive mixtures, evaporation of chemicals, sticky substances, fibrous materials,
coarse dust, soot and oil particles or environments favourable for the formation of hazardous substances (toxic substances, dust,
pathogenic germs).
THE UNIT SHOULD NOT BE OPERATED BY CHILDREN OR PERSONS WITH REDUCED
PHYSICAL, MENTAL, OR SENSORY CAPACITIES, OR THOSE WITHOUT
THE APPROPRIATE TRAINING.
THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY QUALIFIED
PERSONNEL AFTER THE APPROPRIATE BRIEFING.
THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORIZED
ACCESS BY UNATTENDED CHILDREN.
DELIVERY SET

6
VUT 160/250/350 PB EC
www.ventilation-system.com
TECHNICAL DATA
MODEL VUT 160 PB EC VUT 250 PB EC VUT 350 PB EC
Supply voltage, 50 (60) Hz [V] 1~ 220 – 240
Nominal power consumption [W] 50 101 170
Current [A] 0.4 0.8 1.3
Maximum air flow [m3/h] 190 270 410
RPM, min-1 3770 4480 3200
Sound pressure level at 3 m distance [dBA] 26 28 34
Transported air temperature [°C] from -25 up to +40
Casing material aluzinc steel
Insulation (mineral wool) [mm] 40 mm 40 mm 40 mm
Extract filter G4
Supply filter F7
Connected air duct diameter [mm] Ø 125 Ø 125 Ø 160
Weight [kg] 48 48 70
Heat recovery efficiency from 82 up to 94 % from 80 up to 98 % from 80 up to
91 %
Heat exchanger type counter-flow
SEC class A+ A A+
The unit is designed for indoor application with the ambient temperature ranging from +1 °C up to +40 °C and relative humidity up to 80 %.
In order to prevent condensation on the internal walls of the units, it is necessary that the surface temperature of the casing is 2-3 °C higher
than the dew point temperature of the transported air.
The unit is rated as a Class I electrical appliance.
Hazardous parts access and water ingress protection rating:
• IP22 for the unit connected to the air ducts
• IP44 for the unit motors
The unit design is constantly being improved, thus some models may be slightly different from those described in this manual.
TECHNICAL DATA

7
www.ventilation-system.com
RIGHT-HANDED MODIFICATION
LEFT-HANDED MODIFICATION
H1
H
A2
A
A1
B1 B3 ØD
Ø16
Ø10,2
8 holes
B2
B
AB
L3
L5 L L2
L4
A view (indoor connection)
B view (outdoor connection)
L4
L2 L1 L6
L3
L3
L5 L L2
L4
A view (outdoor connection)
B view (indoor connection)
L4
L2 L1 L6
L3
Model Dimensions [mm]
ØD A A1 A2 B B1 B2 B3 H H1 L L1 L2 L3 L4 L5 L6
VUT 160 PB EC 125 1008 1105 1073 754 822 480 410 320 361 386 293 245 31 128 123 216
VUT 250 PB EC 125 1008 1105 1073 754 822 480 410 320 361 386 293 245 31 128 123 216
VUT 350 PB EC 160 1138 1235 1203 1044 1112 680 610 320 361 555 417 345 40 119 144 282

8
VUT 160/250/350 PB EC
www.ventilation-system.com
The unit has the following operating logic: warm stale extract air from the room flows into the unit, where it is filtered by the extract filter,
then air flows through the heat exchanger and is exhausted outside by the extract fan. Cold fresh air from the outside flows into the unit,
where it is cleaned by the supply filter.
Then the air flows through the heat exchanger and is directed to the room with the supply fan. Heat energy of warm extract air is
transferred to clean intake fresh air from the outside and warms it up. The air flows are fully separated while flowing through the heat
exchanger. Heat recovery minimizes heat losses, which reduces the cost of space heating in the cold season.
The difference between the supply and extract air flow temperature leads to condensate generation. Condensate is collected in the drain
pan and is removed outside through the drain pipe.
UNIT DESIGN
1 10
11
12
10
13
14
2
3
4
5
9
6
7
8
1 – cable glands; 2 – supply fan; 3 – control unit; 4 – bypass damper; 5 – extract filter; 6 – counter-flow heat exchanger; 7 – drain pan; 8 –
detachable plates for technical maintenance of filters; 9 – drain pipe; 10 – duct electric preheater connector; 11 – extract fan; 12 – supply
filter; 13 – duct electric reheater connector (for VUT 160/250/350 PB EC A21 units); 14 – SETUP MODE button (for VUT 160/250/350 PB EC
A21 units).
Additional equipment (is not included in the delivery set, can be ordered separately)
Humidity sensor.
The HV2 humidity sensor is connected to the controller in VUT 160/250/350 PB EC A21 models, and to the terminal block in
VUT 160/250/350 PB EC A14 models. The HR-S humidity sensor is connected to the controller. The unit with the installed humidity sensor
maintains a set indoor humidity point. As the extract air humidity rises above the set point, the system automatically switches to the
maximum speed. As the humidity drops down below the set point the unit returns to the previous mode.
CO2sensor (connected to the controller)
Measures the level of concentration of carbon dioxide in the room and generates a signal that controls the performance of the fan. Air
capacity control based on CO2concentration is an efficient energy saving solution.
VOC sensor (connected to the controller)
Qualitative assessment of air saturation with contaminants (cigarette smoke, exhaled air, solvent and detergent vapours).
The sensor sensitivity can be adjusted with regards to the expected maximum level of air pollution.
Enables on-demand ventilation which results in considerable energy savings as air is exchanged only upon reaching the preset level of
pollution.
Duct preheater.
The heater maintains the duct air temperature at a point that prevents the heat exchanger freezing. Heater installation and connection
to the unit are described in the heater user’s manual.
Duct reheater.
The heater maintains the room temperature set by the user. Heater installation and connection to the unit are described in the heater
user’s manual.
UNIT DESIGN AND OPERATING PRINCIPLE

9
www.ventilation-system.com
Compatibility table of optional equipment and unit models
HV1 internal
humidity sensor
HV2 internal
humidity sensor
CO2-1 room sensor CO2-2 room sensor
Room humidity
sensor
VOC room sensor
(0-10 V)
CO2 room sensor
(0-10 V)
Room humidity
sensor (0-10 V)
Preheater
Reheater
VUT 160/250/350 PB EC A11 + — — — — — — — + —
VUT 160/250/350 PB EC A14 — + + + + — — — — —
VUT 160/250/350 PB EC A21 — + + + + + + + + +
RIGHT-HANDED AND LEFT-HANDED MODIFICATIONS
The figure below shows the arrangement of spigots for left- and right-handed modifications. Choosing the right arrangement can
improve the ease of installation, shorten the length of the ducts and reduce the number of air duct bends.
EXTRACT AIR EXTRACT AIR
LEFTHANDED MODIFICATION RIGHTHANDED MODIFICATION
SUPPLY AIR SUPPLY AIR
INTAKE AIR EXHAUST AIREXHAUST AIR INTAKE AIR

10
VUT 160/250/350 PB EC
www.ventilation-system.com
UNIT OPERATION MODES
Heat recovery mode: warm stale extract air from the room flows into the unit, where it is filtered by the extract filter, then air flows
through the heat exchanger and is exhausted outside by the extract fan.
Cold fresh air from the outside flows into the unit, where it is cleaned by the supply filter.
Then the air flows through the heat exchanger and is directed to the room with the supply fan.
Supply air is heated in the heat exchanger by transferring the heat energy of warm and humid extract air to the cold fresh air. The air
flows are fully separated while flowing through the heat exchanger. Heat recovery minimizes heat losses, which reduces the cost of space
heating in the cold season.
EXTRACT AIR
SUPPLY AIR
INTAKE AIR
EXHAUST AIR
Freeze protection (danger of freezing appears when the exhaust air temperature downstream of the heat exchanger is lower than
+5 °C and intake air temperature upstream of the heat exchanger is lower than -3 °C for the units with preheating, and when exhaust
temperature downstream of the heat exchanger is lower than +3 °C for the units without preheating). To protect the heat exchanger from
freezing in the cold season, the unit has a Frost Protection mode based on the temperature sensor readings.
The sensor is installed in the exhaust air duct downstream of the heat exchanger.
The Frost Protection mode is activated at an exhaust air temperature of +3 ˚С.
After temperature increase the unit returns to the previous operation mode.
In VUT 160/250/350 PB EC A11 units the frost protection mode must be activated, see the User’s manual of the control panel. In case of
freezing danger, the supply fan is turned off in VUT 160/250/350 PB EC A14 units. After temperature increase the unit returns to the previous
operation mode. The VUT 160/250/350 PB EC A21 units have three frost protection modes: - gradual reduction of the supply fan speed
- with the bypass - with the electric preheater (if the unit is equipped with a duct preheater). Mode selection and settings are described
in the User’s manual for the control system.
EXTRACT AIR
SUPPLY AIR
INTAKE AIR
EXHAUST AIR

11
www.ventilation-system.com
Summer Cooling mode: the bypass damper is opened, the intake air that is supplied to the premises bypasses the heat exchanger. The
intake air temperature remains constant.
EXTRACT AIR
SUPPLY AIR
INTAKE AIR
EXHAUST AIR

12
VUT 160/250/350 PB EC
www.ventilation-system.com
INSTALLATION AND SETUP
HUMIDITY SENSOR MOUNTING
Remove the service panel and install the humidity sensor into the mount from the side of the extract air duct and connect the humidity
sensor connector to the respective contact socket coming from the control unit.
HV1 sensor:
HV2 sensor:
Install the service panel back to the unit.
READ THE USER'S MANUAL BEFORE INSTALLING THE UNIT.

13
www.ventilation-system.com
UNIT INSTALLATION
To attain the best performance of the unit and to minimise turbulence-induced air pressure losses connect the straight air duct section
to the spigots on both sides of the unit while mounting.
Minimum straight air duct length:
• equal to 1 air duct diameter on the intake side
• equal to 3 air duct diameters on the outlet side
If the air ducts are too short or not connected, protect the unit parts from ingress of foreign objects. To prevent uncontrollable access to
the fans, the spigots may be covered with a protecting grille or other protecting device with mesh width not more than 12.5 mm.
While installing the unit, ensure convenient access for subsequent maintenance and repair.
Fasteners for ceiling mounting are not included in the delivery set and should be ordered separately. While choosing fasteners consider
the material of the mounting surface as well as the weigh of the unit, refer to the Technical data section. Fasteners for unit installation
should be selected by a qualified technician.
Wall and ceiling mounting examples
Nut
Washer
Vibration absorbing rubber
CONDENSATE DRAINAGE
Connect the drain pipe to the sewage system using the SG-32 U-trap kit (available upon separate order). The pipe slope downwards
must be at least 3°.
min 3°
min 3°
Drain hose
U-trap
Sewage system
Drain pipe
Drain hose

14
VUT 160/250/350 PB EC
www.ventilation-system.com
U-trap
Sewage system Drain pipe
Drain hose Drain hose
min 3°
min 3°
The condensate drainage system is designed for normal operation in premises with air temperatures above 0 °C!
If the expected ambient air temperatures are below 0 °C, the condensate drainage system must be equipped with heat insulation and
pre-heating facilities.

15
www.ventilation-system.com
CONNECTION TO POWER MAINS
• The unit is rated for connection to 1~230 V/50 (60) Hz power mains according to the wiring diagram.
• The connection must be made using durable, insulated and heat-resistant conductors (cables, wires). The actual wire cross section
selection must be based on the maximum load current, maximum conductor temperature depending in the wire type, insulation,
length and installation method.
• The external power input must be equipped with a automatic circuit breaker built into the stationary wiring to open the circuit in
the event of overload or short-circuit. The position of the circuit breaker must ensure free access for quick unit power-off. The trip
current of the automatic circuit breaker must exceed the maximum current consumption of the unit (refer to the“Technical data”
section or to the unit label). The recommended trip current of the circuit breaker is the next current in the standard trip current row
following the maximum current of the connected unit.
• The automatic circuit breaker is not included in the delivery set and can be ordered separately.
To access the control unit, remove the service panel.
External wiring diagram for VUT 160/250/350 PB EC A11 units
ССU
(no-contact)
Power input 230 VAC
Х1
1
L
2
N
3
PE
4
L
5
N
6
c
7
no
8
c
9
no
10
+12V
11
GND
12
B
13
A
14
+5V
15
GND
16
Vo
SM1*
12
NL
SM2*
12
NL
PK1*
21
P1
Gnd AB
+12V
t °C
TE1
Gnd Vo+5V
White
Green Brown Yellow
Designation Name Model Wire**
CCU* DX cooler N0 2x0.75 mm2
S1* Supply air damper actuator LF 230 2x0.75 mm2
S2* Extract air damper actuator LF 230 2x0.75 mm2
1* Contact from a fire alarm panel N0 2x0.75 mm2
1 Control panel
1 Outdoor temperature sensor The sensor is installed by the manufacturer in the intake air duct.
*Is not included in the delivery set ** Maximum connecting cable length is 20 m!
ELECTRIC SHOCK HAZARD!
DISCONNECT THE UNIT FROM POWER MAINS PRIOR TO ANY OPERATIONS.
THE UNIT MUST BE CONNECTED TO POWER MAINS BY A QUALIFIED ELECTRICIAN.
THE RATED ELECTRICAL PARAMETERS OF THE UNIT ARE GIVEN ON THE
MANUFACTURER’S LABEL.
ANY TAMPERING WITH THE INTERNAL CONNECTIONS IS PROHIBITED
AND WILL VOID THE WARRANTY.

16
VUT 160/250/350 PB EC
www.ventilation-system.com
External wiring diagram for VUT 160/250/350 PB EC A14 units
The unit has an option of additional external controls connection to the X2 terminal block, which is located on the hinged electrical
mounting plate of the control unit. Extra connections to the unit are shown in dotted lines in the External wiring diagram.
Power input 230 VAC
11
L
22
N
33
PE PK PK +U +U0-10V
44 5 6 7 8910 11 12 13
White
Green
Brown
Yellow
External device
NO (CO2sensor))
Control panel
-Tx Rx +
Tx Rx
3
2
1
GND
+U
0 -10V
GND GNDNО C
X1 X2
SM-L SM-N
Humidity sensor
Electric actuators
of the external air dampers
SM1
supply
L1 N
SM2
exhaust
L1 N
PK fire alarm panel
(remove the jumper while connecting the contact)
ELECTRIC SHOCK HAZARD!
External wiring diagram for VUT 160/250/350 PB EC A21 units
GNDGND
X1
L LPE
N
NONO
A BN NC C
NONO C C NO C NO C
+24V+24V
L N 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
0-10V
GND А В +24V
12
PK1 *
12 12
P1*
12 12 12
CCU*
Boost*
12
SM1*
12
SM2*
U**U**
CO2*
GND 0-10V +24V
Brown
Yellow
Green
White
Power input 230 VAC
Designation Name Contact
type Wire** Note
SМ1* Supply air damper actuator NO 2 x 0.75 mm23 A, 30 V DC/~250 AC
SМ2 * Exhaust air damper actuator NO 2 x 0.75 mm23 A, 30 V DC/~250 AC
РК1* Contact from fire alarm control panel NC 2 x 0.75 mm2
CCU* Cooler control NO 2 x 0.75 mm23 A, 30 V DC/~250 AC
Р1* External control panel 4 x 0.25 mm2
Boost* Contacts ON/OFF Boost NO 2 x 0.75 mm
CO2* External CO2sensor 3 x 0.75 mm
* Not included in the delivery set.
** The U supply voltage of the SM1, SM2 external dampers is selected depending on the type of dampers.
*** Maximum connecting cable length is 20 m!
Output parameters: terminals 17-22 — 3 A, 30 V DC / ~ 250 VAC («dry contact»).
— ELECTRIC SHOCK HAZARD!

17
www.ventilation-system.com
Maintenance operations of the unit are required 3-4 times per year. Maintenance includes general cleaning of the unit and the following
operations:
1. Filter maintenance (3-4 times per year).
Dirty filters increase air resistance in the system and reduce supply
air volume. The filters require cleaning not less than 3-4 times per
year. Vacuum cleaning is allowed. After two consecutive cleanings
filters must be replaced. For new filters, contact the Seller.
To clean or replace the filters, detach the removable plates located
on the service side of the unit. After cleaning install the filters and
the detachable plates in the reverse order.
2. Heat exchanger maintenance (once per year).
Some dust may accumulate on the heat exchanger even in case
of regular maintenance of the filters. To maintain the high heat
recovery efficiency, regular cleaning is required.
The heat exchanger is connected with the drain pan by the fixing
bands that should be removed only in case of heat exchanger
replacement.
The drain pan is fixed to the unit casing using three screws.
To clean the heat exchanger pull it and the drain pan out, drain the
water through the pipes, then flush the heat exchanger with warm
detergent solution. After cleaning install the dry heat exchanger
with the drain pan back to the unit.
DISCONNECT THE UNIT FROM POWER SUPPLY BEFORE
ANY MAINTENANCE OPERATIONS!
TECHNICAL MAINTENANCE

18
VUT 160/250/350 PB EC
www.ventilation-system.com
3. Fan maintenance (once per year).
Even in case of regular maintenance of the filters, some dust may accumulate inside the fans and reduce the fan performance and supply
air flow. Clean the fans with a soft brush or cloth. Do not use water, aggressive solvents, or sharp objects as they may damage the impeller.
4. Technical maintenance of condensate drainage system (once a year).
The condensate drainage (drain line) may get clogged by dirt and dust particles contained in the exhaust air. Pour some water inside the
drain pan to check the pipe for clogging. Clean the U-trap and the drain pipe if required.
5. Ductwork system maintenance (once in 5 years).
Even regular fulfilling of all the maintenance operations prescribed above may not completely prevent dirt accumulation in the air ducts,
which leads to air pollution and reduces the unit capacity. Duct maintenance means regular cleaning or replacement.
6. Control unit maintenance (if necessary).
The control unit is positioned inside the unit casing. For accessing the control unit remove the fixing screws on the service panel and
remove it.
CAUTION! The control unit maintenance must be performed by an expert qualied for unassisted operations with electrical
installations with the voltage up to 1000 V after careful reading of the user’s manual.
TROUBLESHOOTING
Problem Possible reasons Troubleshooting
The fan(s) do(es) not get
started. No power supply.
Make sure the power supply line is connected
correctly, otherwise troubleshoot a connection
error.
Low air flow. Filters, fans or the heat exchanger are soiled. Clean or replace the filters, clean the fans, and the
heat exchanger.
The ventilation system is soiled or damaged. Make sure the air ducts are clean and intact.
Noise, vibration.
The fan impeller is soiled. Clean the impellers.
Fan screw connection is loose. Check tightening torques.
Water leakage. The drainage system is soiled, damaged, or
installed incorrectly.
Clean the drain line if necessary. Check the drain
line slope angle. Make sure that the U-trap is filled
with water and the drain pipes are frost protected.

19
www.ventilation-system.com
STORAGE AND TRANSPORTATION REGULATIONS
• Store the unit in the manufacturer’s original packaging box in a dry closed ventilated premise with temperature range
from +5 ˚С to +40 ˚С and relative humidity up to 70 %.
• Storage environment must not contain aggressive vapors and chemical mixtures provoking corrosion, insulation, and sealing
deformation.
• Use suitable hoist machinery for handling and storage operations to prevent possible damage to the unit.
• Follow the handling requirements applicable for the particular type of cargo.
• The unit can be carried in the original packaging by any mode of transport provided proper protection against precipitation and
mechanical damage. The unit must be transported only in the working position.
• Avoid sharp blows, scratches, or rough handling during loading and unloading.
• Prior to the initial power-up after transportation at low temperatures, allow the unit to warm up at operating temperature for at
least 3-4 hours.

20
VUT 160/250/350 PB EC
www.ventilation-system.com
FOLLOWING THE REGULATIONS STIPULATED HEREIN WILL ENSURE A LONG AND
TROUBLEFREE OPERATION OF THE UNIT.
USER’S WARRANTY CLAIMS SHALL BE SUBJECT TO REVIEW ONLY UPON
PRESENTATION OF THE UNIT, THE PAYMENT DOCUMENT AND THE USER’S MANUAL
WITH THE PURCHASE DATE STAMP.
MANUFACTURER’S WARRANTY
The product is in compliance with EU norms and standards on low voltage guidelines and electromagnetic compatibility. We hereby
declare that the product complies with the provisions of Electromagnetic Compatibility (EMC) Directive 2014/30/EU of the European
Parliament and of the Council, Low Voltage Directive (LVD) 2014/35/EU of the European Parliament and of the Council and CE-marking
Council Directive 93/68/EEC. This certificate is issued following test carried out on samples of the product referred to above.
The manufacturer hereby warrants normal operation of the unit for 24 months after the retail sale date provided the user's observance
of the transportation, storage, installation, and operation regulations. Should any malfunctions occur in the course of the unit operation
through the Manufacturer's fault during the guaranteed period of operation, the user is entitled to get all the faults eliminated by the
manufacturer by means of warranty repair at the factory free of charge. The warranty repair includes work specific to elimination of faults
in the unit operation to ensure its intended use by the user within the guaranteed period of operation. The faults are eliminated by means
of replacement or repair of the unit components or a specific part of such unit component.
The warranty repair does not include:
• routine technical maintenance
• unit installation/dismantling
• unit setup
To benefit from warranty repair, the user must provide the unit, the user's manual with the purchase date stamp, and the payment
paperwork certifying the purchase. The unit model must comply with the one stated in the user’s manual. Contact the Seller for warranty
service.
The manufacturer’s warranty does not apply to the following cases:
• User’s failure to submit the unit with the entire delivery package as stated in the user’s manual including submission with missing
component parts previously dismounted by the user.
• Mismatch of the unit model and the brand name with the information stated on the unit packaging and in the user's manual.
• User’s failure to ensure timely technical maintenance of the unit.
• External damage to the unit casing (excluding external modifications as required for installation) and internal components caused
by the user.
• Redesign or engineering changes to the unit.
• Replacement and use of any assemblies, parts and components not approved by the manufacturer.
• Unit misuse.
• Violation of the unit installation regulations by the user.
• Violation of the unit control regulations by the user.
• Unit connection to power mains with a voltage different from the one stated in the user's manual.
• Unit breakdown due to voltage surges in power mains.
• Discretionary repair of the unit by the user.
• Unit repair by any persons without the manufacturer’s authorization.
• Expiration of the unit warranty period.
• Violation of the unit transportation regulations by the user.
• Violation of the unit storage regulations by the user.
• Wrongful actions against the unit committed by third parties.
• Unit breakdown due to circumstances of insuperable force (fire, flood, earthquake, war, hostilities of any kind, blockades).
• Missing seals if provided by the user’s manual.
• Failure to submit the user’s manual with the unit purchase date stamp.
• Missing payment paperwork certifying the unit purchase.